Metal Clad Wood Patio Doors

SECTION 08557

METAL CLAD WOOD PATIO DOORS

(JELD-WEN W-2500 Series)

Display hidden notes to specifier by using “Tools”/”Options”/“View”/”Hidden Text”.

(Specifier Note: The purpose of this guide specification is to assist the specifier in correctly specifying JELD-WEN®W-2500 Clad Wood Sliding Patio Doors and their installation. The specifier needs to edit these guide specifications to fit the needs of each specific project. Contact a JELD-WEN representative to assist in appropriate product selections. Throughout the guide specification, there are Specifier Notes to assist in the editing of the file. The term Architect is used throughout these guide specifications and may be revised to read “Design Professional,” ” Engineer,” “Owner” or other appropriate designation as required for specific projects).

** NOTE TO SPECIFIER ** JELD-WEN, Inc.; aluminum clad wood patio doors.
This section is based on the products of JELD-WEN, Inc., which is located at:
3737 Lakeport Blvd.
Klamath Falls, OR 97601
Toll Free Tel: 888-535-3936
Tel: 541-850-2606
Fax: 541-851-4333
Web:
As a JELD-WEN customer, you can count on us to provide reliable products and service. We are a comprehensive source for dependable wood, vinyl and aluminum windows; wood and wood composite interior doors; and wood, steel, wood composite and fiberglass exterior doors.

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Aluminum Clad Wood Windows of the Following Types: (JELD-WEN W-2500 Series)

1. Sliding aluminum-clad wood patio doors.

1.2 RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

A. Section 07920 - Joint Sealants.

1.3 REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

A. American Architectural Manufacturer Association (AAMA):

1. ANSI/AAMA/NWWDA 101/I.S.2 /NAFS; Voluntary Specifications for Aluminum, Vinyl (PVC) and Wood Windows and Glass Doors.

2. AAMA 2603; Voluntary Specification, Performance Requirements and Test Procedures for Pigmented Organic Coatings on Aluminum Extrusions and Panels.

B. National Fenestration Rating Council (NFRC):

1. NFRC 100; Procedure for Determining Fenestration Thermal Properties.

2. NFRC 200; Solar Heat Gain Coefficient and Visible Transmittance.

C. Window & Door Manufacturers Association (WDMA):

1. WDMA I.S.4; Water Repellent Preservative Non-Pressure Treatment for Millwork.

1.4 DESIGN REQUIREMENTS

A. Provide windows complying with requirements indicated, based on testing manufacturer's window that are representative of those specified and that are of test size required by AAMA/WDMA/CSA/101/I.S.2/A440.

** NOTE TO SPECIFIER ** Include window design pressure (DP) ratings as part of the performance requirements. Required DP will vary dependent on project site, the location in the building and window size. Coordinate DP with the Structural Engineer. DP ratings and related window size and style are available at or by contacting a JELD-WEN representative. Insert value or refer to drawing information.

B. Structural Requirements: Provide windows complying with requirements indicated:

1. Design pressure: As indicated on drawings.

2. Design pressure: ______.

** NOTE TO SPECIFIER ** Include NFRC ratings as part of the performance requirements. NFRC ratings qualifying for the Energy Star program are based on the performance of the whole window assembly. Qualifying windows vary to fit the needs of different regions throughout the country. NFRC ratings and related JELD-WEN window size and styles are available at or by contacting a JELD-WEN representative. Insert values.

C. NFRC Requirements:

1. Provide windows complying with the following total window ratings:

a. U-Factor: ______in accordance with NFRC 100.

b. Solar Heat Gain Coefficient (SHGC): ______in accordance with NFRC 200.

c. Visible Transmittance (VT): ______in accordance with NFRC 200.

1.5 SUBMITTALS

A. Submit under provisions of Section

B. Product Data: Manufacturer's data sheets on each product to be used, including:

1. Preparation instructions and recommendations.

2. Storage and handling requirements and recommendations.

3. Installation methods.

C. Shop Drawings: Submit shop drawings indicating details of construction, flashings and relationship with adjacent construction.

D. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

E. Quality Assurance Submittals:

** NOTE TO SPECIFIER ** Delete Design Data, Test Reports submittal requirements when propriety specification is used and can be held. MAINTAIN Design Data, Test Reports submittal requirement when other products may be submitted as substitution.)

1. Design Data, Test Reports: Provide manufacturer test reports indicating product compliance with indicated requirements.

F. Closeout Submittals: Refer to Section

1.6 QUALITY ASSURANCE

A. Installer Qualifications: Minimum 2 years installing similar assemblies.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

B. Mock-Up: Provide a mock-up for evaluation of installation techniques and workmanship.

1. Window mock-up shall incorporate surrounding construction, including wall assembly fasteners, flashing, and other related accessories installed in accordance with window manufacturer's approved installation methods.

2. Do not proceed with remaining work until workmanship is approved by Architect.

3. Rework mock-up as required to produce acceptable work.

** NOTE TO SPECIFIER ** Delete provision not required.

4. Mock-up may not remain as part of the work.

5. Mock-up may remain as part of the work.

C. Pre-installation Meeting: Conduct pre-installation meeting on-site two weeks prior to window installation start.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Deliver windows materials and components in manufacturer's original, unopened, undamaged containers with identification labels intact.

B. Store windows as recommended by manufacturer.

1.8 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.9 WARRANTY

A. Manufacturer standard warranty indicating that the patio door unit will be free from material and workmanship defects from the date of substantial completion for the time periods indicated below:

1. Window Unit: 20 years.

2. Cladding Finish: 10 years against peeling, checking, cracking caulk or color change.

3. Insulated Glass: 20 years against seal breakage.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: JELD-WEN, Inc., which is located at: 3737 Lakeport Blvd.; Klamath Falls, OR 97601; Toll Free Tel: 888-535-3936; Tel: 541-850-2606; Fax: 541-851-4333; Web:

B. Requests for substitutions will be considered in accordance with provisions of Section

2.2 ALUMINUM-CLAD WOOD PATIO DOOR ASSEMBLlES

A. Basis of Design: Metal-clad wood patio door assemblies as manufactured by JELD-WEN, Inc.

1. Patio Door Type: Sliding patio doors, clad wood construction.

B. Patio Door Fabrication:

1. Panels: Corners machine clamped, joined with finger-joint-pur corners.

2. Glass: Mounted using silicone glazing compound on exterior and retainer held bead on interior.

3. Cladding: Aluminum corners are jointed and sealed.

C. Frames:

1. Material: Select kiln-dried pine AuraLast treated wood.

2. Jamb Width: 4-9/16 inches (116 mm).

3. Cladding 0.050 inch (1.27 mm) extruded aluminum.

** NOTE TO SPECIFIER ** Number of panels per patio door unit varies by door size. Include number of panels under "Size" in Part 3 Schedule Article.

D. Panels:

1. Materials: Select kiln-dried pine AuraLast treated wood and engineered wood substrate. Select members have a LVL core.

2. Cladding: 0.055 inch to 0.100 inch (1.4 mm to 2.5 mm) extruded aluminum, finish to match exterior finish.

3. Thickness: 1-3/4 inches (44.5 mm).

4. Layout: 3-11/32 inches (85 mm) stiles and rails face width.

E. Exterior Trim:

1. Nailing Fins and Drip Caps: Integral extruded aluminum on head and jambs.

2. Frame Expanders: 1-7/8 inches (48 mm).

3. Frame Expanders: 3-1/4 inches (83mm).

4. Mull Expanders: 2-1/8 inches (54 mm).

F. Extension Jambs: Applied at head and sides of frame interior in wall depths up to 12 inches.

G. Weatherstripping:

1. Head: Ivory colored rigid vinyl parting stop with pile weatherstripping and aluminum track at operating head.

2. Meeting Stiles: Ivory colored fiberglass interlock sealed with dense pile weatherstripping.

3. Side Jambs: Ivory colored rigid vinyl parting stop with pile weatherstripping.

4. Sill: Pile weatherstripping.

H. Sills: Standard one-piece pultruded fiberglass and stainless steel track.

I. Sills: Provide optional molded ABS plastic sill pan.

J. Hardware:

1. Sliding System: Two sets of adjustable steel single steel ball bearing rollers.

K. Glazing for Patio Doors:

1. Strength: Tempered glass.

2. Glazing Type: Insulated glass.

a. Description: Two panes of glass utilizing continuous roll formed stainless steel spacer and dual seal sealants.

b. Overall Nominal Thickness: 3/4 inch (19 mm).

c. Coating on No. 2 Surface: Standard, Low-E.

3. Glazing Type: Monolithic glass.

** NOTE TO SPECIFIER ** Fill in blank below with value between 1/8 inch (3.2 mm) and 1/4 inch (6.4 mm) as applicable or insert the phrase 'As scheduled and indicated on Drawings'. Delete option for overall nominal thickness not required.

a. Overall Nominal Thickness: ______

L. Exterior Sliding Insect Screens:

1. Material: Charcoal fiberglass mesh screen cloth (18 by 16 mesh) set in .040 inch (1 mm) extruded aluminum frame with adjustable steel rollers.

M. Grilles:

1. Type: Simulated Divided Lites (SDL).

a. Exterior Muntins:

1) Material: Extruded aluminum permanently applied to exterior of insulating glass unit.

2) Pattern: As scheduled and indicated on Drawings.

b. Interior Muntins

1) Material: Clear pine permanently bonded to interior of insulating glass unit.

2) Width: Match exterior muntin.

2. Type: Full Surround Wood Grilles.

a. Material: Unfinished clear pine.

b. Profile: Modified OGEE.

c. Pattern: As scheduled and indicated on Drawings.

d. Size: 7/8 inch (22 mm).

3. Type: Grilles Between the Glass (GBG).

a. Material: Made of roll formed aluminum suspended within the air cavity.

b. Pattern: As scheduled and indicated on Drawings.

PART 3 EXECUTION

3.1 EXAMINATION

A. Inspect window prior to installation. Inspect rough opening for compliance with window manufacturer recommendations. Verify rough opening conditions are within recommended tolerances.

3.2 PREPARATION

A. Prepare windows for installation in accordance with manufacturer's recommendations.

3.3 INSTALLATION

A. Install windows in accordance with manufacturer's installation guidelines and recommendations Comply with manufacturer's published instructions for installation type. Install in proper relationship with adjacent work.

3.4 FIELD QUALITY CONTROL

A. Manufacturers' Field Services: Field inspections.

3.5 CLEANING

A. Remove Preserve film from glass. Clean the exterior surface and glass with mild soap and water.

3.6 PROTECTION

A. Protect installed windows from damage.

** NOTE TO SPECIFIER ** Sample schedule for specific project. When a single type of window is utilized on a project, specifier may elect to delete the schedule in its entirety. When schedules are included on the drawings, schedule should be deleted from the specification.

3.7 SCHEDULES

A. Window Type A:

1. Style:

2. Operation:

3. Size:

4. Exterior Finish:

5. Interior Wood:

6. Interior Finish:

7. Exterior Trim:

8. Extension Jamb:

9. Hardware:

10. Hardware Finish:

11. Glazing:

12. Grilles:

13. Insect Screen:

14. Screen Frame Finish:

END OF SECTION

08557-1