Price/Proposal No. 65– Disk Dated 5-01-2011 Prices and specifications subject to change without notice.

PA 10/3

STANDARD SPARTAN MODEL PA 10/3 HEAVY-DUTY, HIGH SPEED, HYDRAULIC, HORIZONTAL, METAL CUTTING BANDSAW WITH 5 H.P. AND 1-1/4” BLADE

Capacity: 8” x 11.5” Rectangle (200 x 300mm), 10” Round (250mm).

Blade: 1.25” x .042” x 11’ 6” (32 x 1.07 x 3505mm).

Blade Tension: Hydraulically controlled tension (30,000 psi) provides consistent square cutting accuracy. Includes a motion detector that will shut the machine off should the blade break or stall.

SpeedRange: 70 - 330 SFPM (21 - 101 m/min) variable through a frequency inverter drive and heavy-duty worm gear transmission. The broad speed range allows for optimum cutting of a large spectrum of materials. Aread out on the operator’s touch screen assures accurate speed setting.

Hydraulic Down Feed: Feed rate and down pressure can be controlled independently for fast, accurate cutting. Setup is made easy through the color-coded dial allowing the operator to select the optimum setting for the type of material being cut. Both settings are made at the operator’s station.

Hydraulic Shuttle Feed: Length settings of 0 - 16” are selected with a hand-wheel and displayed on a digital counter. The shuttle comes to positive stops at both ends of the index, assuring cutoff length accuracy. Repeatability is + .005 per index. Up to 9 cycles are possible using the multi-index system.

Motors: Blade Drive: 5 H.P. (3.75 kW). Hydraulic Pump Motor: 1 H.P. (.75 kW). Coolant Pump Motor: 1/8 H.P.

(0.09 kW). Machines are available with either 230 or 460 volt, 3 ph., 60 Hz. Electrics. Voltage must be specified on original order. (208 VOLTS, AVAILABLE WITH OPTION V10/SP2095 FOR AN ADDITIONAL $1,645.00).

Operator’s Control Panel is conveniently mounteded on the left hand side of the machine and offers full control of all machine functions such as; Vises, Blade Speed, Saw Frame, Bundle Clamping, Parts Counter, Shuttle Advance & Retract, Coolant and Work Light. (A stand alone operator’s control console is available as an option).

Piece Counter: The machine will stop the automatic cycle when the pre-set number of cuts has been reached.

Out-of-Stock Switch: The machine will shut off automatically when material is no longer present in the rear vise.

Blade Guides: The combination roller bearing and carbide blade guides reduce heat and blade stress providing longer blade life and accuracies of + .002 per inch of cut material.

Fast Approach: Work height is automatically set allowing the head to rise just enough to clear the workpiece, reducing cycle time and allowing for faster cutting performance.

Automatic Chip Removal: The chip auger rotating in the coolant return removes chips quickly and efficiently, freeing the operator to perform more productive operations. Coolant is allowed to drain back to the tank before the chips are removed from the machine

Chip Brush: Powered from the main drive shaft of the saw, the brush changes speed along with the blade to assure that chips are being removed from each gullet of the blade, improving cutting performance and blade life.

Full Stroking Hydraulic Vise Jaws: The front vise jaws are split to reduce the remnant to as little as 2”. The split vise jaws also help to reduce burrs left on the material and are ideal for bundle cutting. Holding the workpiece on both sides of the blade reduces vibration, providing more accurate cuts and longer blade life.

Work Light: Positioned directly over the work area to provide better illumination of the cutting area, the work light can be turned on and off independently from the operator’s control panel.

PRICE: Complete machine, ready to operate including motors and controls…………………………. $ 26,250.00

Note: The Spartan PA10 is also available with a Touch Screen Programmable Control, Model No. PA10/3/EPC.

PA10/3 – Page 2.

OPTIONAL EQUIPMENT:

Hydraulic Hold Downs: Option Code P10/G1 - Nesting fixtures for vertical clamping are designed for high-production multiple cutting of bundles and shapes. Vertically mounted hydraulic clamps located on each vise jaw apply downward pressure to hold multiple bar work or structural shapes. Min. capacity: 1-1/2” x 5-1/2”. Max. capacity: 4-3/4” x 8”.………………..…………………………………………………..………….….$ 1,895.00

Variable Vise Pressure: Option CodePA10/M9A Hydraulic clamping pressure to the work holding jaws can be adjusted as required to hold solid or thin wall material, allowing the piece to be held securely and without distortion……………………………………………………………………………….………………………$ 1,175.00

Free Standing Control Console: Replaces standard control console mounted to machine base with a free standing pedestal and flexible electrical and hydraulic lines…………………………………………….$ 1,500.00

MATERIAL HANDLING CONVEYORS:

First Section Dead Roller Table: PA10/F055 5’ (1524mm) long. Table is constructed from 4” x 5.4 lb. Channel with five 2.5” (63mm) diameter ball bearing rollers on 12” Centers. This is the first table required for either the loading or discharge side of the machine………………………………………..………...…..$ 705.00

Extension Roller Table: PA10/X055 5’ (1524mm) long. Table is constructed from 4” x 5.4 lb. Channel with five 2.5” (63mm) diameter ball bearing rollers on 12” Centers. For use as extension to first section …..$ 535.00

Coolant Pan: Option Code PA10/E11 Fitting PA10/X055 & F055 roller conveyors, the coolant pan collects and returns coolant back to machine. Included is the pan, V-trough, and hangers………..………….$ 275.00

WARRANTY: Marvel Manufacturing Company, Inc. warrants to the original user for a period of (2) years parts, (1) year labor from date of factory shipment, that every new Spartan metal sawing machine is free from defect in material and workmanship. During that period, we will, at our option, repair or replace any part which, upon examination, we find defective. This warranty will not apply to alterations or modifications made upon Spartan metal sawing machines without our written consent, or to machines which have been subject to willful abuse.

Prices: NET F.O.B. Factory. All prices contained herein are subject to change without notice and are further subject to an increase equal to the amount of any Federal, State, or Local Tax that may be imposed.

Marvel Manufacturing Company, Inc. also reserves the right to make design changes and/or modifications on machines without prior notice.

No officer, employee, representative, or agent is authorized to bind the company to acceptance of any order in the field. All orders are subject to acceptance by the company at its home office in Oshkosh, Wisconsin. Delivery dates given are estimates only, based on prevailing conditions and available information, and are subject to conditions and contingencies beyond our control.

Marvel Manufacturing Company, Inc. • 3501 Marvel Drive • Oshkosh, WI 54902 • U.S.A.

Phone: (920) 236-7200 (800) 472-9464 Fax: (920) 236-4156

Sales & Service Centers/Warehouses

OSHKOSH, WI • 1 800 472-9464 • FAX: 1 920 236-4156

FT. WORTH, TX • 1 817 535-2183 • FAX: 1 817 531-1163

LONGVIEW, WA • 1 360 575-9917 • FAX: 1 360 575-9706

BIRMINGHAM, AL • 1 205 916-2828 • FAX: 1 205 916-2827

District Sales Managers and Technical Specialists in Major Cities