Thermacure paint
Thermacure High Temperature Paint is suitable for woodburning stoves, multifuel stoves, metal chimineas, barbecues, firepits, firebaskets and fireplace trims, withstanding temperatures of up to 650degrees C.
Thermacure paint is available in aerosols or in tins for brush on application.
Guide to Spray-on high temperature paint application
Directions for use
· For best results this product should be used on bare metal.
· Allsurfaces should be clean, dry and free from dust and grease.
· Existing painted surfaces should be prepared to provide a good key for the new paint to adhere to.
· In order to check for compatibility between paints you should always test the paint on a small inconspicuous area first, and follow the heat up procedure outlined below. We cannot guarantee compatibility with all paints so this procedure must be followed.
· Before applying the paint all surfaces should be cold and all forms of ignition turned off.
· Shake can vigorously for 2 minutes after mixing ball rattles.
· Ensure work area is well-ventilated and you are not spraying near naked flames or incandescent materials.
· Spray towards object 300-375mm (12-15”) from surface.
· Press spray firmly and use steady even strokes.
· Gently replace nozzle with a twisting motion pointing away from you.
· For cleaning purposes invert can and spray for a few seconds until only clear solvent escapes.
· During the spraying process, whilst drying, and for the first three times you use the appliance you should open windows and doors, and if necessary use fans, to provide a fresh airflow as the paint may give off fumes and smoke.
· Use kindling only on the first couple offires after applying the paint, burning for 15-20 minutes with the second burn being started whilst the appliance is still warm.
· A full fire should be burnt for 45-60 minutes again, starting whilst the appliance is still warm, then allowed to cool naturally. This will finish the curing process, no further fumes or odour should now be produced and the paint will have reached it's maximum hardness.
Guide to Brush-on high temperature paint application
Thermacure High Temperature Paint is suitable for woodburning stoves, multifuel stoves, metal chimeneas, barbecues, firepits, firebaskets and fireplace trims, withstanding temperatures of up to 650degrees C.
Directions for use
· For best results this product should be used on bare metal
· Any surface should be clean, dry and free from dust and grease.
· Existing painted surfaces should be prepared to provide a good key for the new paint to adhere to.
· In order to check for compatibility between paints you should always test the paint on a small inconspicuous area first and follow the heat up procedure outlined below. We cannot guarantee compatibility with all paints so this procedure must be followed.
· Before applying the paint all surfaces should be cold and all forms of ignition turned off.
· Stir contents thoroughly to allow paint to mix prior to use.
· Ensure work area is well-ventilated and you are not using the paint near naked flames or incandescent materials.
· If you are using the paint in a spray gun direct towards object 300-375mm (12-15”) from surface and use steady even strokes.
· This product is a one-coat paint and if more than one-coat is required the second coat should be applied whilst the first coat is still wet.
· Do not apply more paint than is necessary. If the paint is applied too thickly this can result in blistering.
· During the painting process, whilst drying and for the first three times you use the appliance open windows, doors and if necessary use fans to provide a fresh airflow as the paint may give off fumes and smoke.
· Use kindling only on the first 2 fires burning for 15-20 minutes with the second burn being started whilst the appliance is still warm.
· A full fire should be burnt for 45-60 minutes again starting whilst the appliance is still warm, then allowed to cool naturally.
Warnings
· Thermacure is a one-coat paint and if more than one-coat is required the second coat should be applied whilst the first coat is still wet.
· Do not apply more paint than is necessary.
· If the paint is applied too thickly this can result in blistering.
· If a blockage occurs remove nozzle with a twisting motion and clean.
· Never stick sharp objects into the can.
· Thermacure high temperature paint cannot be used on vitreous enamelled surfaces and is suitable only for metal substrates.
· We cannot confirm its suitability on any other surfaces or materials.
· Please contact us should you have any additional questions relating to this product.