Changes in the program version 16.0 compared with the 15.0 program version

1. New slat AER44m/S is introduced in the programme.

2. New slat PD/77 is introduced in the programme.

3. New guide rails GR83x33/eco and GR83x33I/eco are introduced in the programme.

4. New end slats ESL9x50/eco and ESL9x50I/eco are introduced in the programme.

5. Tube support FS18/APB in introduced in the programme (it may be included in the roller shutter specification manually).

6. Mounting box MB/IP55 is introduced in the programme (it may be included in the roller shutter specification manually only).

7. One channel radio control Radio 8113 micro is introduced in the programme.

8. The article one-channel radio control Radio 8113-IP has been changed for Radio 8113 IP65M-sensor.

9. The algorithm to calculate the tube length for roller shutter with ‘Springs’ suspension system is corrected.

10. The values of parameter “Length” are changed for the following electric motors: “NR2/100-12“, “NR2/140-8“, “NR2/60-12“ and “NR2/80-12“.

11. The algorithm for length calculation has been changed for end slats "ES/P9" and "ES/P14".

12. The algorithm of calculation of maximal load capacity of octagonal tubes for combined systems with unified control has been corrected.

13. The algorithm of calculation of parameter “Required torque moment” (used in the process of roller shutter calculation at choice of the electric motor) for combined roller shutter systems with unified control has been corrected.

14. The algorithm of calculation of parameter “Required load capacity” has been corrected for combined roller shutter systems. It is used in the process of roller shutter calculation at choice of strap coiler, rope coiler, cord coiler, pulley, gear and push-up springs.

15. For combined roller shutter systems the conditions of a warning message has been revised – “The maximal curtain weight (35 kg) for roller shutters with the chosen suspension (

Security lock”) is exceeded!”

16. It is not allowed to change the parameters of the roller shutter – “The position of the tube” for combined systems that has been calculated.

17. Calculation of combined systems is possible with shutter boxes 137 and 150 mm.

18. Calculation of combined systems is possible with the following box types: “Half-round”, “Round”, “Extruded half-round” and “Extruded round”.

19. End caps “SF165/D“, “SF165/I“, “SF180/D“, “SF180/I“, “SF205/D“ and “SF205/I“ are not available.

20. New end caps “SF45/137/D“, “SF45/150/D“, “SF45/165/D“, “SF45/180/D“ and “SF45/205/D“ are available.

21. New end caps "SF45/137/I", "SF45/150/I", "SF45/165/I", "SF45/180/I" and "SF45/205/I" are available.

22. New end caps "SF45/150/IQ", "SF45/165/IQ", "SF45/180/IQ" and "SF45/205/IQ" are available.

23. New end caps “SF-R/137/D“, “SF-R/150/D“, “SF-R/165/D“, “SF-R/180/D“ and “SF-R/205/D“ are available.

24. New end caps “SF-R/137/I“, “SF-R/150/I“, “SF-R/165/I“, “SF-R/180/I“ and “SF-R/205/I“ are available.

25. New end caps “SF-R/150/IQ“, “SF-R/165/IQ“, “SF-R/180/IQ“ and “SF-R/205/IQ“ are available.

26. New end caps “SF-QR/137/D“, “SF-QR/150/D“, “SF-QR/165/D“, “SF-QR/180/D“ and “SF-QR/205/D“ are available.

27. New end caps “SF-QR/137/I“, “SF-QR/150/I“, “SF-QR/165/I“, “SF-QR/180/I“ and “SF-QR/205/I“ are available.

28. New end caps “SF-QR/150/IQ“, “SF-QR/165/IQ“, “SF-QR/180/IQ“ and “SF-QR/205/IQ“ are available.

29. New tube support “S/IQ” is available.

30. Ball bearing support “SBB12/30“is available.

31. Suspension type “Security lock” is available for roller shutter with a mosquito net.

32. AER42 as basic profile is available for roller shutters with a mosquito net.

33. New operation manual “R7010104” is available.

34. Additional parameter (flag) is introduced – “When calculating a roller shutter allow the choice of the sticker "R7010563", that allows/prohibits the choice of sticker (article "R7010563") when calculating roller shutters (see programme section “Parameters”).

35. Additional parameter (flag) is introduced – "When calculating a roller shutter allow the choice of the product passport - "R7010111",that allows/prohibits the choice of the passport (article "R7010111") when calculating roller shutters (see programme section “Parameters”).

36. Additional parameter (flag) is introduced – "When calculating a roller shutter allow the choice of the operation manual - "R7010104", that allows/prohibits the choice of the operation manual (article "R7010104") when calculating roller shutters (see programme section “Parameters”).

37. Found mistakes are corrected.