Chabot College Spring 2007
Course Outline for Automotive Technology 68
CAIFORNIA BAR BASIC AND ADVANCED CLEAN AIR CAR COURSE
Catalog Description:
68 - California BAR Basic and Advanced Clean Air Car Course 5 units
(May be repeated three times)
Motor vehicle emission inspection and maintenance. Includes the Bureau of Automotive Repair (BAR) requirements for the Basic Clean Air Car Course (BCACC) and the Advanced Clean Air Car Course (ACACC). The BCACC includes BAR regulations, Smog Check test procedures, an overview of emissions control devices, and current OBDII requirements and updates. The ACACC includes the Dyno Transition and Advanced Emissions Diagnosis requirements. Required for eligibility to take the State Licensing exam at completion of the course: one year trade experience in emissions/tune up, or nine semester units (13 quarter units) in Automotive Technology, or 180 hours at an accredited automotive school. Automotive Service Excellence (ASE) certification in the Electrical (A6), Engine Performance (A8), and Advanced Engine Performance (L1) also required in order to take the State Exam. The BAR A6, A8, and L1 ASE alternative courses are not included in this course. 4 hours lecture, 4 hours laboratory.
[Typical contact hours: lecture 70, laboratory 70]
Prerequisite Skills:
None
Expected Outcomes for Students:
Upon completion of the course, the student should be able to:
1. perform a three day calibration on the designated Emissions Analyzer;
2. perform two (2) training mode smog inspections meeting BAR and instructor requirements;
3. pass with a minimum of 70% correct, the material required in the California BAR Basic and Advanced Clean Air Car Course;
4. apply either through manipulative, oral, or written assignments and/or discussion, any materials covered or assigned by the instructor;
5. understand the concepts, techniques, principles, and legal requirements for shop and agency requirements;
6. meet the requirements for verification of completion for those individuals subject to Citation compliance.
Course Content:
1. Overview of the Clean Air Car course modules
2. Introduction to automotive emissions and State I/M Program
3. Cause and effect of emissions
4. Fundamentals of the internal combustion engine and combustion theory
5. Infrared exhaust analyzer and diagnostics
6. Evaporative and crankcase emission control systems
7. Thermostatic air clean systems
8. Exhaust gas recirculation systems
9. Secondary air management systems
10. Catalytic converter systems
Chabot College
Course Outline for Automotive Technology 68, Page 2
Spring 2007
11. Computer control technologies
12. Smog Check inspection and repair procedures
13. Dyno operation and safety procedures
14. Advanced emissions diagnosis
15. OBDII operation
16. Advanced Evaporative Emissions diagnosis
17. Scanner Mode 6 operation
18. CAN bus systems
19. Shop and agency practices
20. Hazardous material handling
21. Shop safety
Methods of Presentation:
1. Lecture and demonstration
2. Laboratory
3. Video tapes, slides, overhead projections, computer/internet
4. Guest speakers
Assignments and Methods of Evaluating Student Progress:
1. Typical Assignments
a. Read assigned sections of the Laws & Regs book and be prepared to discuss
b. Complete worksheet utilizing information from lecture
c. Demonstrate use of 4 or 5 gas analyzer
d. Demonstrate use of the of the Emissions Information System (Smog Check Machine)
2. Methods of Evaluating Student Progress
a. Class participation
b. Mandatory completion of BAR attendance criteria
c. Performance in the laboratory projects
d. Laboratory work sheets
e. Homework assignments
f. Quizzes
g. BAR required exams on each section of the class
Textbook(s) (Typical):
Smog Check Manual, Bureau of Automotive Repair, 1993
Clean Air Packet, Bureau of Automotive Repair, 1993
Laws and Regulations, Bureau of Automotive Repair, 2004
Write it Right, Bureau of Automotive Repair, 2003
Napa OBDII, Napa Automotive, 1996
Advanced Emissions Diagnosis, Aspire, 2004
Advanced Evaporative Emissions & Mode 6 operation (To be announced)
Motor Magazine extracts
Chabot College
Course Outline for Automotive Technology 68, Page 3
Spring 2007
Special Student Materials:
1. Safety glasses
2. Shop/safety clothing
3. Special packet of books and supplies available at the bookstore
sas 09/2006
AT 68 course outline