All Glass Horizontal Sliding Walls

SECTION 08490

ALL GLASS HORIZONTAL SLIDING WALLS

Display hidden notes to specifier. (Don't know how? Click Here)

** NOTE TO SPECIFIER ** DORMA; Architectural door hardware products.
.
This section is based on the products of DORMA, which is located at:
Dorma Dr. Drawer AC
Reamstown, PA 17567-0411
Toll Free Tel: 800-523-8483
Tel: 717-336-3881
Fax: 800-274-9724
Email:request info ()
Web:
[Click Here] for additional information.
Elegance, Versatility & Beauty, these are qualities that make DORMA the leading designer and manufacturer of accessories and hardware systems for tempered glass entrances.
With an eye on aesthetics and beauty, architects and interior designers focused on incorporating the elegance of glass into their plans want accessories and hardware systems that are aesthetically pleasing and compatible with their designs. This is DORMA.
This specification includes DORMA All Glass Sliding Walls and Sliding Doors, Horizontal Sliding Walls and Sliding Door systems. DORMA also manufactures Structural Glass Curtain Wall components and All Glass Entrance and Storefront components. Contact DORMA for additional information.
See our SpecWizard:Click Here

PART 1 GENERAL

1.1 SECTION INCLUDES

** NOTE TO SPECIFIER ** Delete items below not required for project.

A. All glass sliding doors and sidelights.

B. All glass sliding stacking walls.

C. All glass folding horizontal sliding walls.

D. Horizontal folding slings glass walls fully framed.

1.2 RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

A. Section 05100 - Structural Metal Framing: Door Frames.

B. Section 07900 - Caulking

C. Section 08450 - All Glass Entrances and Storefronts.

D. Section 08710 - Door Hardware: Cylinder locks.

E. Section 08800 - Glass and Glazing: General glazing requirements.

F. Section 08970 - Structural Glass Curtainwalls.

G. Section 09620 - Gypsum Board Assemblies: Adjacent construction for recessed frames and closers.

H. Section 16120 - Electrical Supply and Termination.

1.3 REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

A. ANSI Z97.1 Safety Glazing Materials Used in Buildings - Safety Performance Specifications and Methods of Tests.

B. ASTM C 1036 Specification for Flat Glass

C. ASTM C 1048 Specification for Heat-Treated Flat Glass - Kind FT

D. CPSC 16 CFR 1201 Architectural Glazing Standards and Related Materials.

1.4 DESIGN / PERFORMANCE REQUIREMENTS

A. Wind Loads: Design and size components to withstand dead loads and live loads caused by positive and negative wind loads acting normal to plane of wall, including building corners.

1. Design Wind Load: As calculated in accordance with applicable code, as measured in accordance with ASTM E 330.

B. Deflection: Limit deflection to flexure limit of glass with full recovery of glazing materials.

1.5 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's data sheets on each product to be used, including:

1. Preparation instructions and recommendations.

2. Storage and handling requirements and recommendations.

3. Installation methods.

4. Operation and maintenance data.

C. Shop Drawings:

1. Include plans, elevations, sections, details, attachments to other construction, and accessories. Indicate dimensions, weights, conditions at openings and at storage areas, and required installation, storage, and operating clearances.

2. Indicate details of track and door connections, rail sections, fittings and hardware components.

3. Indicate glass type, sizes and details.

4. Indicate location and installation requirements for hardware and track including floor tolerances required and direction of travel. Indicate blocking to be provided by others.

5. Setting Drawings: Show imbedded items and cutouts required in other work, including support beam punching template.

D. Verification Samples: For each finish product specified, two samples, representing actual product finishes. Show the full range of color and texture variations expected.

1. Aluminum extrusions: 6-inch (150 mm) long sections of rails and other items.

2. Glass: Sample nominally 12 inched by 12 inches (305 mm by 305 mm) of color and thickness desired showing exposed-edge finish.

E. Manufacturer's Certificates: Certify products meet or exceed specified requirements.

F. Manufacturers warranties.

G. Contract Closeout: Submit

1. As-Built Record Documents showing actual installation conditions and wiring.

2. Manufacturer's Warranty.

3. Parts lists and maintenance instructions including data on operating hardware, lubrication requirements, and inspection procedures related to preventative maintenance.

1.6 QUALITY ASSURANCE

A. Manufacturer Qualifications: Glass door manufacturer to have minimum five years documented experience in the fabrication of glass doors of the type required for this project and be capable of providing field service representation during installation.

B. Installer Qualifications: Experienced installer to have minimum five years documented experience in the work of this section and who has specialized in the installation of work similar to that required for this project.

1.7 DELIVERY, STORAGE, AND HANDLING

A. Store products in manufacturer's unopened packaging until ready for installation.

B. Protect materials from damage and exposure to moisture.

1.8 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

B. Field Measurements: Verify opening dimensions of all-glass entrances by field measurements before fabrication and indicate the measurements on Shop Drawings. Coordinate fabrication schedule with construction progress to avoid delaying the Work.

1.9 WARRANTY

A. Provide written warranty signed by the fabricator of the glass doors and glass door systems agreeing to provide a two year warranty covering replacements of those doors that develop manufacturing defects defined as any defect materially obstructing vision through the glass, and any mechanical failure of hardware which prevents the proper operation of the doors and appropriate installation.

1.10 COORDINATION

A. Coordinate Work with other operations and installation of adjacent surfaces to avoid damage to installed materials.

B. Coordinate work with adjacent floor, wall, and ceiling construction to accommodate frame anchorage, panel track, and concealed hardware.

C. Coordinate work with concrete floors and floor finishes for adequate tolerances and clearances between door panels and floor finish.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: DORMA, which is located at: Dorma Dr. Drawer AC; Reamstown, PA 17567-0411; Toll Free Tel: 800-523-8483; Tel: 717-336-3881; Fax: 800-274-9724; Email:request info (); Web:

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 GLASS PRODUCTS

A. General:

1. Safety Glazing Standard: Provide fully tempered glass, Kind FT, compiling with ASTM C 1036 and ASTM C 1048 requirements, including glass indicated by reference to type, class, quality.

2. Sizes: Fabricate glass to size required for openings indicated, with edge clearances and tolerances complying with recommendations of glass and hardware manufacturer.

3. Provide glass types and thickness as indicated on the Drawings.

** NOTE TO SPECIFIER ** The following paragraphs include glass door and sidelight systems for DORMA Agile 150, Agile 150 Syncro, RS120 and RS40. This product is typically used in retails and commercial building as all glass doors and sidelight or room dividers. Select models required and delete if not required. If more than one type is required clearing indicate the location of each on the Drawings.

2.3 ALL GLASS SLIDING DOOR AND SIDELIGHT COMPONENTS

A. DORMA AGILE 150 Sliding Doors and Entrance:

1. Configuration:

** NOTE TO SPECIFIER ** Select one or more of the following configuration paragraphs and delete the paragraphs not required. If more than one type is required clearing indicate the location of each on the Drawings.

a. Single Panel Side Sliding.

b. Single Panel Side Sliding with Side Panel.

c. Bi-Parting Side Sliding.

d. Bi-Parting Side Sliding with Side Panels.

e. As indicated on the Drawings.

** NOTE TO SPECIFIER ** The following paragraph for DORMA Agile 150 Syncro is optional. Select if required and delete if not required. If more than one type is required clearing indicate the location of each on the Drawings.

2. Synchronized Operation: Provide double-paneled sliding door sets with a concealed cable and pulley return system to open and close as bi-parting doors when just one of the panels is operated.

3. Track: Anodized extruded aluminum, full width track with end caps.

** NOTE TO SPECIFIER ** Select one of the following two mounting paragraphs and delete the paragraphs not required.

a. Ceiling Hung Track. Size 2-1/2 inches (63 mm) high by 2-1/8 (54 mm) wide.

b. Wall Mounted Track. Size 2-1/2 inches (63 mm) high by 2-1/4 (57 mm) wide.

c. Side Screen Track. Size 2-1/2 inches (63 mm) high by 2-7/8 (72 mm) wide.

d. Top track:

e. Provide with an adjustable integrated end of travel stop contained within the top track.

f. Finish:

** NOTE TO SPECIFIER ** Select one of the following finish paragraphs and delete the paragraphs not required.

1) Clear anodized aluminum.

2) Brushed similar to Satin Brushed #4 Stainless Steel.

3) As selected by the Architect from manufacturer's standard finishes..

4. Carriers: Concealed clamp-on roller carriers, two per panel, adhesively bonded.

5. Door Panels: Maximum weight 240 pounds (110 kg).

6. Hardware:

a. Floor Guide: Provide as required.

b. Single Door or Active Leaf Locksets: Manufacturer's standard patch dead-bolt locksets:

** NOTE TO SPECIFIER ** Select one of the following two location and function locking paragraphs and delete the paragraph not required.

1) Location and Function: Bottom patch fitting dead bolt. Dead bolt operated by key outside and thumb-turn inside and engaging a dust proof strike.

2) Location and Function: Center lock housing with hook bolt engaging into a matching strike housing or wall strike with aluminum lever handles.

** NOTE TO SPECIFIER ** Select one of the following two inactive leaf locking paragraphs and delete the paragraph not required.

3) Inactive-Leaf Locksets: Manufacturer's standard hook-bolt locksets.

4) Inactive-Leaf Locksets: Bottom patch fitting dead bolt engaging a dust proof strike. Dead bolt operated by key outside and thumb turn inside.

5) Cylinders: As specified in Section 08710 Door Hardware.

c. Hardware Finish:

** NOTE TO SPECIFIER ** Select one of the following finish paragraphs and delete the paragraphs not required. Consult factory for bronze clad and custom powder coat finishes available.

1) Clear anodized aluminum.

2) Brushed similar to Satin Brushed #4 Stainless Steel.

3) As selected by the Architect from manufacturer's standard finishes..

7. Door Panel Glazing:

a. Clear Glass: Conforming to the requirements of Section 08800.

1) ASTM C1048, Kind FT (fully tempered), Condition A (uncoated surfaces), Type I (transparent), Class 1 (clear) requirements.

2) Provide products that have been tested for surface and edge compression according to ASTM C 1048 and for impact strength according to CPSC 16 CFR, part 1201 for Category II materials.

b. Thickness:

** NOTE TO SPECIFIER ** Select paragraph for thickness required and delete the paragraph not required.

1) 3/8 inch (10 mm).

2) 1/2 inch (12 mm).

c. Exposed Edges: Flat polished.

d. Butt Edges: Flat ground.

e. Corner Edges: Mitered.

8. Sidelight Glazing:

a. Clear Glass: Conforming to the requirements of Section 08800.

1) ASTM C1048, Kind FT (fully tempered), Condition A (uncoated surfaces), Type I (transparent), Class 1 (clear) requirements.

2) Provide products that have been tested for surface and edge compression according to ASTM C 1048 and for impact strength according to CPSC 16 CFR, part 1201 for Category II materials.

b. Thickness:

** NOTE TO SPECIFIER ** Select paragraph for thickness required and delete the paragraphs not required.

1) 3/8 inch (10 mm).

2) 1/2 inch (12 mm).

c. Exposed Edges: Flat polished.

d. Butt Edges: Flat ground.

e. Corner Edges: Mitered.

f. Sidelights captured by anodized extruded aluminum U channels integral to the top track assembly.

g. Bottoms are held within anodized extruded aluminum U channels or glass clamps.

h. Aluminum Finish:

** NOTE TO SPECIFIER ** Select one of the following finish paragraphs and delete the paragraphs not required.

1) Clear anodized aluminum.

2) Brushed similar to Satin Brushed #4 Stainless Steel.

3) As selected by the Architect from manufacturer's standard finishes..

B. DORMA RS120 Sliding Doors and Entrance:

1. Configuration:

a. Single Panel Side Sliding with Side Panel.

b. Bi-Parting Side Sliding with Side Panels.

c. As indicated on the Drawings.

2. Track: Anodized extruded aluminum, full width track with end caps.

** NOTE TO SPECIFIER ** Select one of the following two mounting paragraphs and delete the paragraph not required.

a. Ceiling Hung Track. Size 1.65 inches (42 mm) high by 1.87 (47.5 mm) wide.

b. Wall Mounted Track. Size 1.65 inches (42 mm) high by 1.87 (47.5 mm) wide.

** NOTE TO SPECIFIER ** Select one of the following two track cover paragraphs and delete the paragraph not required.

c. Track Cover: Size 5-1/2 inches (140 mm) high.

d. Side Track Cover: Size 5-1/2 inches (1400 mm) high.

e. Provide with an adjustable integrated end of travel stop contained within the top track.

f. Finish:

1) Clear.

3. Carriers: Concealed clamp-on roller carriers, two per panel.

4. Door Panels:

** NOTE TO SPECIFIER ** Select one of the following weight paragraphs and delete the paragraphs not required.

a. Maximum weight 265 pounds (120 kg) with two carriers.

b. Maximum weight 330 pounds (150 kg) with three carriers.

5. Hardware:

a. Floor Guide: Provide as required.

b. Locksets: Manufacturer's standard patch dead-bolt locksets:

** NOTE TO SPECIFIER ** Select one of the following two location and function locking paragraphs and delete the paragraph not required.

1) Location and Function: Bottom patch fitting dead bolt. Dead bolt operated by key outside and thumb-turn inside and engaging a dust proof strike.

2) Location and Function: Center lock housing with hook bolt engaging into a matching strike housing or wall strike with aluminum lever handles.

** NOTE TO SPECIFIER ** Select one of the following two inactive leaf locking paragraphs and delete the paragraph not required.

3) Inactive-Leaf Locksets: Manufacturer's standard hook-bolt locksets.

4) Inactive-Leaf Locksets: Bottom patch fitting dead bolt engaging a dust proof strike. Dead bolt operated by key outside and thumb turn inside.

5) Cylinders: As specified in Section 08710 Door Hardware.

c. Hardware Finish:

** NOTE TO SPECIFIER ** Select one of the following finish paragraphs and delete the paragraphs not required. Consult factory for bronze clad and custom powder coat finishes available.

1) Clear anodized aluminum.

2) Polished stainless steel.

3) Brushed stainless steel.

4) As selected by the Architect from manufacturer's standard finishes..

6. Door Panel Glazing:

a. Clear Glass: Conforming to the requirements of Section 08800.

1) ASTM C1048, Kind FT (fully tempered), Condition A (uncoated surfaces), Type I (transparent), Class 1 (clear) requirements.

2) Provide products that have been tested for surface and edge compression according to ASTM C 1048 and for impact strength according to CPSC 16 CFR, part 1201 for Category II materials.

b. Thickness:

** NOTE TO SPECIFIER ** Select paragraph for thickness required and delete the paragraph not required.

1) 3/8 inch (10 mm).

2) 1/2 inch (12 mm).

c. Exposed Edges: Flat polished.

d. Butt Edges: Flat ground.

e. Corner Edges: Mitered.

7. Sidelight Glazing:

a. Clear Glass: Conforming to the requirements of Section 08800.

1) ASTM C1048, Kind FT (fully tempered), Condition A (uncoated surfaces), Type I (transparent), Class 1 (clear) requirements.

2) Provide products that have been tested for surface and edge compression according to ASTM C 1048 and for impact strength according to CPSC 16 CFR, part 1201 for Category II materials.

b. Thickness:

** NOTE TO SPECIFIER ** Select paragraph for thickness required and delete the paragraph not required.

1) 3/8 inch (10 mm).

2) 1/2 inch (12 mm).

c. Exposed Edges: Flat polished.

d. Butt Edges: Flat ground.

e. Corner Edges: Mitered.

f. Sidelights captured by anodized extruded aluminum U channels integral to the top track assembly.

g. Bottoms are held within anodized extruded aluminum U channels or glass clamps.

h. Aluminum Finish:

1) Clear.

2.4 ALL GLASS SLIDING STACKING GLASS WALL COMPONENTS

A. DORMA Horizontal Sliding Walls: HSW ARCOS, Fully Glazed with arc shaped door rails.

** NOTE TO SPECIFIER ** DORMA HSW System can be configured in several ways. Stacking arrangements can be combined with panels for single action or double action doors. Consult with DORMA and indicate the configuration system required on the Drawings. Indicate location of single and double acting doors required. If more than one configuration is required clearing indicate the location of each on the Drawings. Edit the following paragraphs to suit the configuration required.

1. Configuration: Provide configuration as indicated on the Drawings.

2. Top and Bottom Rail: Anodized extruded aluminum top and bottom rails with arch shape with top and bottom pivots and hangers as required.

a. Finish:

** NOTE TO SPECIFIER ** Select one of the following finish paragraphs and delete the paragraphs not required.

1) Clear anodized aluminum.

2) Brushed similar to Satin Brushed #4 Stainless Steel.

3) As selected by the Architect from manufacturer's standard finishes..

3. Operation:

a. Manual.

4. Non Sliding Single or Double Action Door Panels with Pivots:

a. Maximum weight 330 pounds (150 kg) per panel.

b. Maximum height 10 feet (3.05 mm).

c. Maximum panel width 4 feet 1-1/4 inches (1250 mm).

5. Sliding Single or Double Action Door Panels:

a. Maximum weight 200 pounds per panel.

b. Maximum height 10 feet.

c. Maximum panel width 4 feet 1-1/4 inches (1250 mm).

6. Track: Extruded aluminum with white powder coating, full width track with end caps.

** NOTE TO SPECIFIER ** Select the track type required from the following paragraphs and delete the paragraphs not required.

a. Straight Track. Size 2.95 inches (75 mm) high by 2.83 (72 mm) wide.

b. Segmented Track. Size 2.95 inches (75 mm) high by 2.83 (72 mm) wide.

c. Transition Track. Provide transition track components as required including 90 degree T, 90 degree L, 135 degree T, curved section angles. Size 2.95 inches (75 mm) high by 2.83 (72 mm) wide.