Truck & Trailer Specialties
6726 Hanna Lake Rd. S.E.
Dutton, Mich. 49316
Ph-616-698-8215, Fax-616-698-0972
PLOW TRUCK DEMO
01-06-2012
Dump Body and Hoist
Crysteel Select Dump Body Including:
Body construction is 304 stainless steel
10’ long, 84” inside width, 96” outside width
26” side height, 42” front height, 32” rear height
Western style understructure with 12” longsills
Long sills are ¼” material and are continuously welded
¼” AR400 steel floor
7 gauge 304 stainless steel sides and ends
Tailgate is 32” tall and is double wall construction, 7 gauge 304 stainless steel outer panel and 3/16” AR400 inner panel
½ cab shield is 10 gauge 304 stainless steel construction
Tailgate is double acting and air operated
Boxed top rail
Pressed horizontal side braces
Body is 100 % continuously welded
Dirt shedding top rails, pillars and tailgate
Understructure and floor to be painted black
Stainless steel finish comes bare, no paint
Crysteel Model M5390 trunnion mounted telescopic hoist
NTEA Class 70, hoist is double acting
Hoist has a mounting cradle and pivot point have grease zerks
Body prop included
Mud flaps installed in front and behind drive tires
Body up proximity light with light mounted in the cab
Sound Off LED Model ECV062STT stop/turn/tail lights recessed in rear pillars
Sound Off LED model EOVREBZA amber flashers recessed in rear pillars
Sound Off LED marker lights
Sound Off LED amber flashers and LED tail lights mounted in poly light boxes and installed on the rear side of the spreader
Star Model 255HTC amber strobe light mounted on the cab shield, visible 360 degrees
2 scraper lights wired on 1 switch and 1 spreader light wired on a separate switch
Wired Rite switch box for low oil light, low oil over ride switch, tarp control, spreader diverter switch, body up light and air tail gate switch
SS bar grate steps installed over the dual wheels, street side
Tarp System:
Roll Rite Aluminum Electric tarp system
High torque electric motor with aluminum wind deflector
Aluminum tarp bow set, aluminum tension bow set, 30 degree elbows
3 spring under body pivot set
16’ black knit mesh tarp cover
Underbody Scraper:
Monroe Model MS3512
Moldboard is 12’ long, 1” thick and 20” tall, heat treated with a pressed in offset
1 piece 1” circle with 5” center bolt with grease groove and welded in bushing
Dual power reverse cylinders with 2” nitrate rods and poly pak seals
Reverse cylinders mounted on 2” pivot pins
Dual actuating cylinders with 2” nitrated rods and poly pak seals, cylinders are housed in a canister retained by a 4 bolt flange and include HD shock assemblies
Hanger board is ½” plate reinforced by ½” x 7-1/2” flat plate and a ¾” rod bar the full length of the hinge
Circle hold down blocks are 20.5” x 7” and have a 3/8” UHMW poly wear plate and are contoured to follow the shape of the circle
Cross over relief valve, cushion valve and port relief for down pressure are included
Scraper comes with a black powder coat finish and the ends of the moldboard shall be painted orange
Serrated bar step mounted on the moldboard
Standard cutting edge, ½” x 6” x 72” carbon steel
Fuel/Hydraulic Tanks:
Riverside fuel/hydraulic tanks mounted behind the cab with proper mounting brackets and straps
Tanks to be 10 gauge steel construction
80 gallon fuel oil and 30 gallon hydraulic oil capacity
Sight and temp gauge
Low oil shut down system with indicator light on the dash
Vented and filtered fill cap
Zinga type return line filter is to be tank mounted
Ball shut off valve mounted on 2” suction line
In tank suction screen in 3” port
Tanks painted to match the cab, straps to be painted black
Step mounted on the end of the fuel tank
Hydraulic System:
Rex Roth A10V071 front mounted piston hydraulic pump with solenoid operated shut down valve mounted on the pressure port
Low oil shut down and over ride circuit
1310 series front drive line
2” pump flange on supply port
Rex Roth Model M4-12 load sense hydraulic valve with pressure compensated flow controls
Air operated sections for dump body hoist, scraper up/down, scraper swing, front plow up/down, front plow swing, and EPC sections for conveyor, spinner and pre wet system
Stainless steel valve enclosure with hoses ported through the bottom of enclosure and mounted on the frame rail on LH side of chassis
Air control levers shall be Morse type with pressure protection
Dickey John Control Point spreader control with granular and liquid drivers
Console in cab to house controls
Cushion valve for front plow reverse circuit installed at front hitch area
Plumbing to rear of body with hydraulic couplers for spreader
Plumbing to front with couplers for front plow use
Pre-Wet System:
Monroe hydraulic pre-wet system
7 GPM hydraulic pump directly coupled to the hydraulic motor, pressure relief system
Fiberglass enclosure mounted with stainless brackets, enclosure to house hydraulic hoses, pump and flow meter, hoses use bulkhead fitting to the side of the enclosure
Pre-wet system to be operated using the Dickey-John Control Point controller
Flow meter and application rate sensor to be included
System includes a one way poly check valve
Brass spray nozzles include stainless steel guards
Suction side has a Y strainer with SS mesh strainer
Suction port has a poly type ball valve
All fittings are glass filled polypropylene type, hoses are EPDM type
System shall include a flusher kit and 2” cam lock fitting for bulk filling
Two 75 gallon pre wet tanks are 3/8” wall rotationally molded polypropylene with built in baffles
Tanks have fill caps at the top and have gallon markers on the end, vent on the top
Discharge fitting are molded in type
Tank mounting straps are 304 stainless steel
Tanks are equipped with a crossover kit to tie them together
V-Box Spreader
Monroe Model MSV-120-84-56/304
Body is 10’ long, 84” wide, 56” high sides
6.5 cubic yard capacity
Hopper is 10 gauge 304 stainless steel
2” double crimped top edge
Body long sills are 7 gauge 304 stainless steel
Cross sills are 3” x 4.1# channel and tie the lower edge of the longsills to side supports
The front of the body will be sloped to accommodate a dump body doghouse
The screw adjustable feed gate is 10 gauge 304 stainless and has a ruler, the feed gate is 12” X 18”
10 gauge 304 stainless side supports on 24” centers
Lift loop provided at each corner
Rear endplate has inside reinforcements
The conveyor chain is 24” wide and has 10 gauge stainless steel bolt on chain covers
Conveyor floor is 3/16” stainless and is replaceable
The conveyor chain is driven by a worm drive gear box with a low speed/high torque
orbital type hydraulic motor directly coupled to the gear box
White motor with a built in application rate sensor
Cast iron gear box mounted on a 2” drive shaft, hardened bronze gears running in oil
The gear box is 50:1
Drive and idler sprockets are 8 tooth cast iron keyed to 2” drive and idler shafts
4 bolt flange bearings with grease zerks
Internal front and external rear wipers
Front chain adjuster is spring loaded and has 4” of adjustment
The front bearing has an extension for adjustment at the rear of the body
The front bearings have a grease extension to the rear of the body
Heat treated, 2.25 pitch self cleaning pintle chain with 7/16” pins, 21.000 lb tensile strength and uses 3/8” x 1-1/2” crossbars welded to every other link, 4.5” on center
The poly spinner disc is 20” diameter and has 6 molded in flights
The disc is mounted to a replaceable hub and connected to the top mounted motor
Rear Spinner Assembly
½ Y-chute with air operated deflector to direct material either to center line chute or center mounted spinner
Tip up spinner assemble
Side delivery chute will be poly lined
Pre-wet spray nozzles to be mounted above the deflector chute
A tailgate latch assemble in 304 stainless steel to mount V-box using dump body latch fingers, the front of the V-box will be secured using 4” nylon straps with winches that attached to the V-box, brackets to be attached to the dump body for 4” flat hooks
A step using bar grate material installed on the V-box above dump body step
Front Hitch & Bumper
Install 34” Husting hitch complete with a double acting lift cylinder w/nitrated rod
12” H.D. channel front bumper with tapered ends and all necessary supports and braces for front plow use
Front plow lights mounted with stainless steel or aluminum brackets use round head SS bolts
Hitch area will be painted black
General
All hoses and fittings installed per City specification
Crysteel warranty on dump body and hoist is 5 years, 100% parts and labor for years 1-3 and 50% for years 4-5
All other components are covered under a 1 year warranty
Monroe Junior mid-mount wing
Moldboard is 7’ long, 27” intake height and 28” discharge
3/16” moldboard with 3/8” ribs
H.D. spring cushioned push arm with shear pin
Front cross tube with mounting plate
4” x 4” x ¾” bottom angle, 4” x 10” toe cylinder, 3” x 10” heel cylinder
Safety chain for transport
Wing post has a U shaped support at the top of the wing post
Rear push arm has a 6” cushion spring
Rear push arm support brace is constructed of 4” x 6” x ¼” tubing and is supported by both frame rails
Install sequencing valve for proper operation of the wing, valve has built in checks to prevent drifting while not in use
Sequencing valve has built in manually adjustable flow controls
Hydraulic disconnects for easy removal
Wing is cushioned with a rubber stop in stored position
Welding on the moldboard is continuous
Install a work light on the curb side to illuminate the wing
A poly 1 hole light box installed on the end of the wind with a red LED light
Reverse curve steel cutting edge
Additional air operated hydraulic valve for wing operation
Delete 75 gallon pre-wet tank on the curb side to off set the weight of the wing
****INSTALLED $74,464.00
Includes junior wing
Submitted by: Dan Bouwman/Roger Hill