Copyright 2015 AIAMasterSpec Premium12/15

PRODUCT MASTERSPEC LICENSED BY ARCOM TO CLARKDIETRICH BUILDING SYSTEMS.

Copyright 2015 by The American Institute of Architects (AIA)

Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA

This Product MasterSpec Section is licensed by ARCOM to ClarkDietrich Building Systems ("Licensee").

This Product MasterSpec Section modifies the original MasterSpec text, and does not include the full content of the original MasterSpec section.

Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by, or representative of the opinions of, ARCOM or The American Institute of Architects (AIA). Neither AIA nor ARCOM are liable in any way for such revisions or for the use of this Product MasterSpec Section by any end user. A qualified design professional should review and edit the document to suit project requirements.

For more information, contact ClarkDietrich Building Systems, 9100 Centre Pointe Dr., Suite 210, West Chester, OH 45069; Phone: (513) 870-1100; Fax: (513) 870-1300; Website: Email: .

For information about MasterSpec contact ARCOM at (800) 424-5080 or visit

SECTION 054000 - COLD-FORMED METAL FRAMING

TIPS:

To view non-printing Editor's Notes that provide guidance for editing, click on MasterWorks/Single-File Formatting/Toggle/Editor's Notes.

To read detailed research, technical information about products and materials, and coordination checklists, click on MasterWorks/Supporting Information.

Revise this Section by deleting and inserting text to meet Project-specific requirements.

This Section uses the term "Architect." Change this term to match that used to identify the design professional as defined in the General and Supplementary Conditions.

Verify that Section titles referenced in this Section are correct for this Project's Specifications; Section titles may have changed.

PART 1 - GENERAL

1.1RELATED DOCUMENTS

Retain or delete this article in all Sections of Project Manual.

  1. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division01 Specification Sections, apply to this Section.

1.2SUMMARY

  1. Section Includes:
  2. Load-bearing wall framing.
  3. Exterior non-load-bearing wall framing.
  4. Interior non-load-bearing wall framing exceeding height limitations of standard, nonstructural metal framing.
  5. Floor joist framing.
  6. Roof rafter framing.
  7. Ceiling joist framing.
  8. Soffit framing.
  9. Related Requirements:

Retain subparagraphs below to cross-reference requirements Contractor might expect to find in this Section but are specified in other Sections.

  1. Section055000 "Metal Fabrications" for miscellaneous steel shapes, masonry shelf angles, and connections used with cold-formed metal framing.
  2. Section092116.23 "Gypsum Board Shaft Wall Assemblies" for interior non-load-bearing, metal-stud-framed, shaft-wall assemblies, with height limitations.
  3. Section092216 "Non-Structural Metal Framing" for standard, interior non-load-bearing, metal-stud framing, with height limitations and ceiling-suspension assemblies.

1.3PREINSTALLATION MEETINGS

Retain "Preinstallation Conference" Paragraph below if Work of this Section is extensive or complex enough to justify a conference.

  1. Preinstallation Conference: Conduct conference at [Project site] <Insert location>.

If needed, insert list of conference participants not mentioned in Section013100 "Project Management and Coordination."

1.4ACTION SUBMITTALS

  1. Product Data: For each type of product.
  2. Sustainable Design Submittals:
  3. Product Data: For recycled content, indicating postconsumer and preconsumer recycled content and cost.

Retain one of two “LEED Submittals” Paragraphs below.

  1. LEED v4 Submittals:
  2. MR Credit: Building Product Disclosure and Optimization - Environmental Product Declarations: Provide Type III EPDs from manufacturers that have third-party verified environmental impact data.
  3. MR Credit: Building Product Disclosure and Optimization - Sourcing of Raw Materials: Provide recycled content of products showing the percentage of postconsumer and/or preconsumer recycled content by weight and its associated cost.
  4. MR Credit: Building Product Disclosure and Optimization - Material Ingredients: Provide Health Product Declarations (HPDs) from manufacturers with full disclosure of known hazards in compliance with the Health Product Declaration Open Standard.
  5. MR Credit: Construction and Demolition Waste Management: Include a statement indicating percentage of materials diverted from disposal in landfills and incinerators, and where recyclable resources are directed back to the manufacturing process.
  6. LEED 2009 Submittals:
  7. Product Data for Credit MR 4.1[ and Credit MR 4.2]: For products having recycled content, provide documentation indicating percentages by weight of postconsumer and preconsumer recycled content. Include statement indicating cost for each product having recycled content.
  8. Product Data for Credit MR2.1[ and CreditMR2.2]: For products diverted from disposal in landfills and incinerators, and where recycled resources are directed back to the manufacturing process, include a statement indicating percentage of materials diverted and recycled and the costs associated with each.
  9. Product Data for Credit MR5: For products where product manufacturing is within a 500 mile(805 km)radius of the jobsite and the point of extraction of the raw materials, include a statement indicating the location and distances for the manufacturing plant and the point of extraction of raw materials in relation to the jobsite location.
  1. Shop Drawings: [Provide shop drawings prepared by cold-formed metal framing manufacturer.]
  2. Include layout, spacings, sizes, thicknesses, and types of cold-formed steel framing; fabrication; and fastening and anchorage details, including mechanical fasteners.
  3. Indicate reinforcing channels, opening framing, supplemental framing, strapping, bracing, bridging, splices, accessories, connection details, and attachment to adjoining work.

Retain "Delegated-Design Submittal" Paragraph below if design services have been delegated to Contractor.

  1. Delegated-Design Submittal: For cold-formed steel framing.

1.5INFORMATIONAL SUBMITTALS

Coordinate "Qualification Data" Paragraph below with qualification requirements in Section014000 "Quality Requirements" and as may be supplemented in "Quality Assurance" Article.

  1. Qualification Data: For testing agency.

Retain "Welding certificates" Paragraph below if retaining "Welding Qualifications" Paragraph in "Quality Assurance" Article.

  1. Welding certificates.

Retain "Product Certificates" Paragraph below to require submittal of product certificates from manufacturers.

  1. Product Certificates: For each type of code-compliance certification for studs and tracks.
  2. Product Test Reports: For each listed product, for tests performed by [manufacturer and witnessed by a qualified testing agency] [a qualified testing agency].
  3. Steel sheet.
  4. Expansion anchors.
  5. Power-actuated anchors.
  6. Mechanical fasteners.
  7. Vertical deflection clips.
  8. Horizontal drift deflection clips
  9. Miscellaneous structural clips and accessories.
  10. Evaluation Reports: For cold-formed steel framing.
  11. Metal stud manufacturer to have a third party evaluation report for its products that are reviewed to the local building code or its model code (IBC 2009 and AISI S100 or IBC 2012 and AISI S100 or IBC2015 and AISI S100).

1.6QUALITY ASSURANCE

  1. Manufacturer Qualifications: Member in good standing of the Steel Framing Industry Association (SFIA).
  2. Products to be certified under an independent third party inspection program administered by an agency accredited by IAS to ICC-ES AC98 IAS Accreditation Criteria for Inspection Agencies.
  3. Engineering Responsibility: Preparation of Shop Drawings, design calculations, and other structural data by a qualified professional engineer.
  4. Professional Engineer Qualifications: A professional engineer who is legally qualified to practice in jurisdiction where project is located and who is experienced in providing engineering services of the kind indicated. Engineering services are defined as those performed for installations of cold-formed metal framing that are similar to those indicated for this project in material, design, and extent.

Retain "Testing Agency Qualifications" Paragraph below if Contractor or manufacturer selects testing agency or if Contractor is required to provide services of a qualified testing agency in "Field Quality Control" Article. Qualification requirements are in addition to those specified in Section014000 "Quality Requirements," which also defines "NRTL" (nationally recognized testing laboratory).

  1. Testing Agency Qualifications: Qualified according to ASTME329 for testing indicated.

Usually retain "Product Tests" Paragraph below. Retain option if permitted. Insert option for testing ductility if required. See "Mill Certification" Paragraph in "Materials" Article in the Evaluations for more information.

  1. Product Tests: Mill certificates or data from a qualified independent testing agency[,or in-house testing with calibrated test equipment,] indicating steel sheet complies with requirements, including base-steel thickness, yield strength, tensile strength, total elongation, chemical requirements, and metallic-coating thickness.

Retain "Code-Compliance Certification of Studs and Tracks" Paragraph below for third-party verification that products meet the requirements of model codes and industry standards. Coordinate retained certification program(s) with the member companies in Part 2 "Manufacturers" Article below. See "Code-Compliance Certification Programs" Article in the Evaluations.

  1. Code-Compliance Certification of Studs and Tracks: Provide documentation that framing members are certified according to the product-certification program of the Steel Framing Industry Association (SFIA).

Retain "Welding Qualifications" Paragraph below if shop or field welding is required. If retaining, also retain "Welding certificates" Paragraph in "Informational Submittals" Article.

  1. Welding Qualifications: Qualify procedures and personnel according to the following:
  2. AWSD1.1/D1.1M, "Structural Welding Code - Steel."
  3. AWSD1.3/D1.3M, "Structural Welding Code - Sheet Steel."
  4. Fire-Test-Response Characteristics: Where indicated, provide cold-formed metal framing identical to that of assemblies tested for fire resistance per ASTME119 by, and displaying a classification label from, a testing and inspecting agency acceptable to authorities having jurisdiction.
  5. Comply with AISI Specifications and Standards.
  6. AISI S100 “North American Specification for the Design of Cold-Formed Steel Structural Members”.
  7. AISI S200 “North American Standard for Cold-Formed Steel Framing – General Provisions”.
  8. AISI S201 “North American Standard for Cold-Formed Steel Framing – Product Standard”.
  9. AISI S211 “North American Standard for Cold-Formed Steel Framing – Wall Stud Design”.
  10. AISI S212 “North American Standard for Cold-Formed Steel Framing – Header Design”.
  11. AISI S213 “North American Standard for Cold-Formed Steel Framing – Lateral Design”.
  12. AISI “Code of Standard Practice for Cold-Formed Steel Structural Framing”.

1.7DELIVERY, STORAGE, AND HANDLING

  1. Protect and store cold-formed steel framing from corrosion, moisture staining, deformation, and other damage during delivery, storage, and handling as required in AISI's "Code of Standard Practice".

PART 2 - PRODUCTS

Manufacturers and products listed in SpecAgent and Masterworks Paragraph Builder are neither recommended nor endorsed by the AIA or ARCOM. Before inserting names, verify that manufacturers and products listed there comply with requirements retained or revised in descriptions and are both available and suitable for the intended applications. For definitions of terms and requirements for Contractor's product selection, see Section016000 "Product Requirements."

2.1MANUFACTURERS

  1. Basis-of-Design Product: Subject to compliance with requirements, provide cold-formed metal framing products by ClarkDietrich Building Systems; as specified in other Part 2 articles or comparable products from members of the SFIA.

2.2PERFORMANCE REQUIREMENTS

Retain "Delegated Design" and "Structural Performance" paragraphs below if Contractor is required to assume responsibility for design.

Coordinate this article with other Part2 articles, deleting prescriptive requirements, such as steel thickness and minimum yield strength unless imposing minimum design restrictions. Insert other performance and design criteria below to suit Project, or add them to Drawings. AIADocumentA201 requires Owner or Architect to specify performance and design criteria to be satisfied.

  1. Delegated Design: Engage a qualified professional engineer, as defined in Section014000 "Quality Requirements," to design cold-formed steel framing.
  2. Structural Performance: Provide cold-formed steel framing capable of withstanding design loads within limits and under conditions indicated.
  3. Design Loads: [As indicated on Drawings] <Insert design loads>.
  4. Dead Loads: [Weights of materials and construction] <Insert applicable dead loads>.
  5. Live Loads: <Insert applicable live loads>.
  6. Roof Loads: <Insert applicable roof loads>.
  7. Snow Loads: <Insert applicable snow loads>.
  8. Wind Loads: <Insert applicable wind loads>.
  9. Seismic Loads: <Insert applicable seismic loads>.
  10. Building Code Requirements: <Insert specific requirements of code authority having jurisdiction>.
  11. Deflection Limits: Design framing systems to withstand[design loads] without deflections greater than the following:

Component deflection limits in first seven subparagraphs below are examples only. Retain deflection limits in applicable subparagraphs, or insert other limits as appropriate for wall, floor, and ceiling finish materials.

  1. Exterior Load-Bearing Wall Framing: Horizontal deflection of [1/240] [1/360] [1/600] [1/720] of the wall height.
  2. Interior Load-Bearing Wall Framing: Horizontal deflection of [1/240] [1/360] of the wall height under a horizontal load of 5 lbf/sq. ft. (239 Pa).
  3. Exterior Non-Load-Bearing Framing: Horizontal deflection of [1/240] [1/360] [1/600] [1/720] <Insert ratio> of the wall height.
  4. Interior Non-Load-Bearing Framing: Horizontal deflection of [1/240] [1/360] of the wall height under a horizontal load of 5 lbf/sq. ft. (239 Pa).
  5. Floor Joist Framing: Vertical deflection of [1/360] [1/480] for live loads and l/240 for total loads of the span.
  6. Roof Rafter Framing: Vertical deflection of [1/120] [1/240] [1/360] of the horizontally projected span for live loads.
  7. Ceiling Joist Framing: Vertical deflection of [1/120] [1/240] [1/360] of the span for live loads and 1/240 for total loads of the span.
  1. Design framing systems to provide for movement of framing members located outside the insulated building envelope without damage or overstressing, sheathing failure, connection failure, undue strain on fasteners and anchors, or other detrimental effects when subject to a maximum ambient temperature change of 120 degF (67 degC).

Retain first subparagraph below for non-load-bearing and load-bearing walls if design responsibility for cold-formed framing is delegated to Contractor. Indicate locations on Drawings if different movement is anticipated for different building elements. If preferred, change deflection limits to ratios, such as L/300 for floors and L/200 for roofs.

  1. Design framing system to maintain clearances at openings, to allow for construction tolerances, and to accommodate live load deflection of primary building structure as follows:
  2. Upward and downward movement of [1/2 inch (13 mm)] [3/4 inch (19 mm)] [1 inch (25 mm)] [1-1/2 inches (38 mm)].

Usually retain subparagraph below for exterior non-load-bearing wall framing, particularly for brick-veneer backup framing.

  1. Design exterior non-load-bearing wall framing to accommodate horizontal deflection without regard for contribution of sheathing materials.

Retain "Cold-Formed Steel Framing Standards" Paragraph below whether delegating design or prescriptively specifying cold-formed steel framing; revise to suit Project.

  1. Cold-Formed Steel Framing Standards: Unless more stringent requirements are indicated, framing shall comply with AISIS100, AISIS200, and the following:

Retain subparagraphs below, as applicable, if Project includes floor and roof systems, wall studs, headers for load-bearing walls, or lateral design requirements.

  1. Floor and Roof Systems: AISIS210.
  2. Wall Studs: AISIS211.
  3. Headers: AISIS212.
  4. Lateral Design: AISIS213.

Retain "Fire-Resistance Ratings" Paragraph below only if products specified are part of a fire-resistance-rated assembly. Indicate rating, testing agency, and testing agency's design designation on Drawings.

  1. Fire-Resistance Ratings: Comply with ASTME119; testing by a qualified testing agency. Identify products with appropriate markings of applicable testing agency.
  2. Indicate design designations from UL's "Fire Resistance Directory" or from the listings of another qualified testing agency acceptable to authorities having jurisdiction.

2.3COLD-FORMED STEEL FRAMING MATERIALS

Retain this article to supplement specific framing articles that follow.

Retain "Recycled Content of Steel Products" Paragraph below to specify recycled content if required. An alternative method of requiring recycled content is to retain requirement in Project's Division01 sustainable design requirements Section that gives Contractor the option and responsibility to determine how recycled content requirements will be met.

  1. Recycled Content of Steel Products: Postconsumer recycled content plus one-half of preconsumer recycled content not less than [25] <Insert value> percent.
  2. Framing Members, General: Comply with ASTM C 955 for conditions indicated.
  3. Steel Sheet: ASTMA1003/A1003M, Structural Grade, TypeH, metallic coated, of grade and coating designation as follows:

Retain minimum grade requirements from options in "Grade" Subparagraph below. If more than one grade option is required, indicate location of each on Drawings.

  1. Grade: [ST33H (ST230H)] [ST50H (ST340H)] [As required by structural performance] <Insert grade>.

Minimum coating requirement for Structural Grade, TypeH steel is designated as CP 60. Retain first option in "Coating" Subparagraph below if ASTMA1003/A1003M's designation of minimum coating thicknesses is required. This minimum coating designation assumes normal exposure conditions and construction practices. When more severe exposure conditions are probable, for example, in coastal areas, consider specifying a heavier coating. BIA recommends G90 (Z275) coating for stud backup applications. Verify availability of heavier-coated steel. If more than one coating designation is required, indicate location of each on Drawings or by inserts.

  1. Coating: [CP 60:G60 (Z180), A60 (ZF180), AZ50 (AZM150), or GF30 (ZGF90)] [G90 (Z275)] <Insert coating designation>.

Retain "Steel Sheet for (Vertical Deflection) (Drift) Clips" Paragraph below if applicable.

  1. Steel Sheet for [Vertical Deflection] [Drift] Clips: ASTM A 1003/A 1003M,ASTMA653/A653M, structural steel, zinc coated, of grade and coating as follows:
  2. Grade: [50 (340), Class1] [As required by structural performance].
  3. Coating: G90 (Z275).

2.4LOAD-BEARING WALL FRAMING

Retain this article if load-bearing steel studs are required. Distinguish location of axial load-bearing framing from exterior non-load-bearing wall framing in paragraphs below or on Drawings. Indicate stud and track web depth on Drawings or insert in paragraphs below.

  1. Steel Studs: Manufacturer's standard C-shaped steel studs, of web depths indicated, punched, with stiffened flanges, and as follows:
  2. Basis-of-Design Product: ClarkDietrichBuilding Systems.

Steel-thickness sequence in "Minimum Base-Steel Thickness" Subparagraph below corresponds to common thickness designators33, 43, 54, 68, and 97 and obsolete 20-, 18-, 16-, 14-, and 12-gauge designations. If retaining different thicknesses for different components, indicate locations here or in framing articles below.