GULF COAST PAINT MFG., INC

CS-662 Matte

Acrylic Lacquer Concrete Sealer

PRODUCT DESCRIPTION

CS-662 is a one component solvent Acrylic Clear Concrete Lacquer that dries to a matte finish. CS-662 has a very fast dry time. CS-662 is designed for use on concrete, masonry, brick and decorative concrete. CS-662 is a non-yellowing sealer. CS-662 has excellent resistance against water and dirt penetration. CS-662 dust proofs concrete by penetrating surface pores leaving a tough durable film.

PRODUCT FEATURES

1. Excellent penetration and high 6. Matte Finish

“wetting out” properties. 7. Non-yellowing

2. Excellent adhesion to concrete. 8. Excellent over decorative Concrete.

3. Good water and salt chemical resistance. 9. Good UV resistance.

4. Prevents “dusting” by increasing 10. Good stain resistance.

strength of concrete surfaces. 11. Ideal as dust proofing sealer.

5. Helps cure and strengthen concrete surfaces. 12. Very fast dry time

TECHNICAL DATA

Color: Clear Recoat Time @ 75°F: 1-2 hours

Gloss: Matte Dry Time: 1 hour @ 75°F

Volume Solids: 22%±2% Tack Free: 15 minutes

Recommended Coverage: Application: Low Pressure Sprayer,

200-360 sq.ft. per gal (coverage varies Mohair roller, or Lambswool Applications

due to surface porosity)

Application Temperature: 50°F to 100°F

Mixing Ratio: One component

Flash Point: 105°F

Induction Time: None

Shelf Life: 1-year minimum

Thinning: None

Packaging: 5 GL. AND 55 GL.

Clean Up: S-74 or SA-50

V.O.C.: 399 GMS/L

CS-662 Page 2

PRODUCT USES

Recommended as a deep penetrating sealer to cure and protect new and old concrete and masonry surfaces from penetration of water, dirt and effects of freeze/thaw cycles. The resulting tight film helps prevent “dusting” of the concrete, spalling, and deterioration. Excellent for driveways, walkways, walls, sidewalks, in pool areas, grocery stores, distribution centers, civic center, sports arenas, and garages. CS-662 is also recommended for masonry, and decorative concrete. CS-662 is not recommended as a protective floor coating. Contact Gulf Coast Paint for epoxy systems for light traffic areas and epoxy/polyurethane systems for heavy traffic areas.

SURFACE PREPARATION

Surface should be sound, clean and DRY. Remove all contaminants, dust, dirt, paint, waxes or other foreign material. Wash floor with a neutral cleaner and allow drying. If oils or grease is present, use a industrial strength degreaser or detergent for removal. The surface should be rinsed thoroughly to remove any residue. Allow surface to dry before applying sealer.

APPLICATION

Mix well with slow speed Explosion Proof Drill and Jiffy mixer. Apply CS-662 with a short nap roller, low-pressure sprayer or lambswool applicator. Apply a uniform wet film; do not puddle material. Do not cover more area that can be worked in 10 minutes due to fast drying time. Two coats may be necessary depending on porosity or type of service. CS-662 is flammable, keep away from open flame. For safety and product curing, proper ventilation is necessary through out application and product cure.

PRECAUTIONS

Do not apply to surfaces below 50°F. Substrate should clean, sound and dry. Any foodstuff in the application area should be removed prior to application. Keep material from freezing. Only use with proper ventilation. Apply a test patch over any questionable surface. Do not use in areas subject to hot oil, grease, etc.

CAUTIONS

CS-662 is combustible. Keep away from all sources of ignition during mixing, application and cure. The use of goggles, fresh air masks or NIOSH approved respirators, protective skin cream and protective clothing is a recommended standard practice when applying coating.

This product is sold without warranty as to performance expressed or implied. Users are urged to make their own tests to determine the suitability for their particular conditions.

NOTE: CS-662 Clear may not meet V.O.C. compliant regulations in some counties in California and other states. Check all local, county and state V.O.C. regulations before using the CS-662 Clear.

SEE MATERIAL SAFETY DATA SHEET FOR FULL SAFETY PRECAUTIONS.

FOR PROFESSIONAL AND INDUSTRIAL USE ONLY

KEEP AWAY FROM CHILDREN

Rev. 09/04

Phone: 251-964-7911 30075 County Rd. 49, Loxley, AL 36551 Fax: 251-964-7918

www.gulfcoastpaint.com