Cisco CCNA Routing and Switching ICND2 200-101 Official Cert Guide
Copyright © 2013 Pearson Education, Inc.
ISBN-10: 1-58714-373-9
ISBN-13: 978-1-58714-373-1
Warning and Disclaimer
Every effort has been made to make this book as complete and as accurate as possible, but no warranty or fitness is implied. The information provided is on an "as is" basis. The author and the publisher shall have neither liability nor responsibility to any person or entity with respect to any loss or damages arising from the information contained in this book or from the use of the CD or programs accompanying it.
When reviewing corrections, always check the print number of your book. Corrections are made to printed books with each subsequent printing.
To make best use this table:
1. Search for the printing number of you book.
2. Ignore all entries listed for a lower numbered (older) printing.
3. Use all entries listed for an equal or higher numbered (more recent) printing.
4. To make a custom list for your printing:
a. Select the rows for printings older (lower numbered) than yours, and delete those rows
b. Select all remaining rows
c. Use the Table…Sort option to sort the table by page number
First Printing: April 2013
Page / Print / Correction564 / 9 / Step 4 – the command, after the word string, should list: {RO | RW}
522 / 9 / Example 17-14 – caption – should list “R2”, not “R1”
378 / 8 / Step 2 text – delete closing phrase “…or the username name secret password command.” This command does not work with CHAP authentication.
381 / 8 / Figure 12-17 – Change R1’s interface ID from S0/0/1 to S0/0/0.
421 / 8 / Example 14-7 – all three interfaces should be “0/1/1” instead of “0/0/0” to match Figure 14-1.
427, 428 / 8 / Examples 14-16 and 14-17 – first line in each – change serial0/0/0 to serial0/1/1.
513 / 8 / Two lines above Example 17-7 – in “…relationship to R4 fails…”, change R4 to R1.
564 / 8 / Step 3 – change “…location of the…” to “…contact for the…”.
55 / 7 / Example 2-4 – 3rd line from the end – begins “Fa0/23” – change to “Fa0/13”.
64 / 7 / 1st sentence after heading “STP Tiebreakers…” – replace the first sentence with: “The figure shows the basic process to choose SW3’s root port, by adding the outgoing port costs along both paths from SW3 to the root (SW1).”
207 / 7 / 4th bullet – end of 1st line – change “…later replying…” to “…later replaying…”
588 / 7 / 1st paragraph, 4th line – “…router will not go…” should be “…router will now go…”.
28 / 6 / Las paragraph – 3rd l ine – inside SW1’s Bridge ID value of 32769:0200:0000:0001, change 0000 to 0001
29 / 6 / 1st bullet in bullet list – change to “The lowest priority”.
52 / 6 / 2nd paragraph, end of 3rd line, ends in “…SW1 then lists” – change “SW1” to “SW2”.
93 / 6 / 2nd paragraph under Example 3-3 – last line – change text “disabled” to “notconnect”.
166 / 6 / 2nd and 3rd paragraphs (ignoring lists) – both discuss action between R3 and SW1; change the SW1 references to “SW3”.
222 / 6 / Table 7-5 – 1st row, description – ends with “IP address” – change to “interface”.
238 / 6 / Figure 8-3 – right side, beneath R2 icon – change “Exstart” to “Exchange”.
401 / 6 / paragraph after figure 13-10 – 4th/5th line – ”The cloud changes the DLCI to 40” should list “42” instead of “40”.
433 / 6 / Last line before example 14-19 – “Figure 14-6” should be “Figure 14-7”.
477 / 6 / Figure 16-8 –change text “Calculated by Router” to “Calculated by Host”.
502 / 6 / Step 4 – last phrase “interface subcommand” should be “router subcommand”.
511 / 6 / 2nd line – bold “ip ospf…” – change “ip” to “ipv6”
512 / 6 / 1st bullet list item - bold “ip ospf…” – change “ip” to “ipv6”
533 / 6 / 4th line – “ipv6 eigrp asn” – change “asn” to “asn” (from bold to not-bold but italicized); it is a parameter, not a keyword.
622 / 6 / Table 21-5 – 1st content row – change show license feature to show license
664 / 6 / In Appendix B, Version 2: Example B-2 and B-3, same error… the show spanning-tree vlan 10 bridge command output lists the wrong bridge ID (1833.9d7b.1380). Change the value to “f47f.35cb.d780”.
666 / 6 / Last paragraph - 2nd line – Change “RSTP” to “STP” in …”RSTP port states of disabled…”.
102 / 5 / Near bottom of paragraph above Table 3-7 – “switchport mode trunk” should be “switchport mode”.
20 / 4 / Output of show vlan brief – Ports listed for VLAN 1 – 3rd row currently reads “Fa0/9, Fa0/10, Fa0/11, Fa0/12” – should instead list “Fa0/10, Fa0/11, Fa0/13, Fa0/14”. Also, in the paragraph below the example, change the reference to Figure 1-1 to 1-2, and the mention of the show vlan command to instead be show vlan brief.
66 / 4 / Item 1 in numbered list – last sentence – replace with “Both commands list both the root port and the root cost (see Example 2-8).”
277 / 4 / Last paragraph before heading “Summary of Interior…” – delete the last two sentences. (Those sentences describe an example that is claimed to cause a problem, but does not. To cause a problem, one router would need its configured hold timer to be less than that same router’s configured hello timer.)
300 / 4 / 2nd paragraph under Example 10-5 – change reference to Example 10-5 to 10-4.
391 / 4 / Question 6 – replace the first two sentences in the question with: “BarneyCo has one central site, with ten remote sites, and Frame Relay PVCs connecting the central site to each remote site.” The answer and explanation do not change.
54 / 2 / 4th paragraph, 2nd-to-last line – change “MaxAge” to “forward delay”.
64 / 2 / 2 lines above the figure – “SW3’s G0/3” should be “SW3’s G0/1”.
166 / 2 / 1st item in first list – delete “vlan” from “switchport mode vlan access”.
199 / 2 / Example 6-6 – bold command – replace “standby” with “glbp”
277 / 2 / last line, 1st paragraph under the figure – change “four times” to “three times”.
277 / 2 / last line, 2nd paragraph under the figure – change “…do not use R1 as a next-hop router.” to reference R2 instead of R1.
286 / 2 / 1st item in bullet list – change “19,000” to “15,000”.
413 / 2 / Step 6B – this step applies only to multipoint subinterfaces. To the end of the step, add text “(multipoint only)”.
563 / 2 / 4-item list, 2nd item – last word is “sting”, but it should be “string”.
594 / 2 / Step 9 (gray highlighted) – replace “and sets a new enable secret password.” with “and needs no passwords to move to enable mode.”
Cisco Press CCNA ICND2 Official Cert Guide – Errata
Last Update: May 12th, 2016