The DOORBRIM Store

15751 Sheridan Street

Fort Lauderdale, Fl. 33331

Tel: (954) 649-4922

E-mail:

Web:

SECTION 08720

Weatherstripping, Weatherseals & Thresholds

(DOORBRIM DOOR HOOD and Heavy Duty DOOR CANOPY)

PART 1GENERAL

1.1 SECTION INCLUDES

  1. Other door trim
  2. Weatherstripping,
  3. Seals
  4. Gaskets
  5. Thresholds

** NOTE TO SPECIFIER ** Revise paragraph below to suit project requirements. If a reader of this section could reasonably expect to find a product or component specified in this section, but it is actually specified elsewhere, then the related section number(s) should be listed in the paragraph below. Add section numbers and titles per CSI MasterFormat and specifier’s practice. In the absence of related sections, delete paragraph below.

1.2 RELATED SECTIONS

  1. Section 066200 - Composite Architectural Features - Plastic Door Hoods and Canopies
  1. Section 07 7120 - Gutters and Downspouts – Door and Window Gutter
  1. Section 087100 – Door Hardware- Door Trim
  1. Section 087500 – Window Hardware- Window Trim
  1. Section 087700 - Door and Window Accessories - Rain Deflector
  1. Section 08 8100 – Metal Doors and Frames
  1. Section 08 8110 – Steel Doors and Frames
  1. Section 08 1050 – Door Accessories
  1. Section 107320 – Awnings and Canopies – Door Hood and Door Canopy

1.3 REFERENCES

** NOTE TO SPECIFIER ** Article below includes submittal of relevant data to be furnished by Contractor before, during or after construction. Coordinate this article with Architect’s and Contractor’s duties and responsibilities in Conditions of the Contract and Division 1 Submittal Procedures Section.

1.4 SUBMITTALS

AGeneral: Submit listed submittals in accordance with Conditions of the Contract and Division 1 Submittal Procedures Section.

BProduct Data: Submit manufacturer’s product data and installation instructions.

CShop Drawings: Provide drawings indicating required component locations, installation interface with adjacent materials, anchorage, fastening and similar information.

DSamples: Submit one each of manufacturer’s standard selection samples.

ECloseout Submittals: Submit the following:

  1. Warranty documents specified herein.

1.5 QUALITY ASSURANCE

  1. Contractor to thoroughly inspect product prior to installation for any visual evidence of damage or defect. If either is present, contact manufacturer.

** NOTE TO SPECIFIER **

1.6 DELIVERY, STORAGE AND HANDLING

  1. Delivery:Allow 3-5 business days for UPS delivery in continental USA.
  2. Storage:Store ABS plastic DOORBRIM products indoors in the original shipping carton until time of installation. Store in an upright position and avoid stacking other items on top.
  3. Handling:Protect the material from adjacent construction activities.

1.7 PROJECT CONDITIONS

1.8 WARRANTY

  1. Return Warranty:

Buyer may return unused DOORBRIMS with the original packing material and box within 10 working days after receipt. Buyer is responsible for the cost of original & return shipping. Buyer must request a “Return Authorization Number” and shipping instructions by emailing us . Please indicate 1) a request to return merchandise and 2) the reason for return. Returns are subject to a 15% restocking fee.

  1. Manufacturer’s Limited Warranty:

Manufacturer warrants material against degradation, chipping or cracking from exposure to weather for a period of 5 years from date of purchase. Warranty is void due to mishandling, improper installation, abuse, accidental damage or negligence.

PART 2 PRODUCTS

2.1 DOORBRIM Door Hood and Door Canopy

  1. MANUFACTURER:

The DOORBRIM Store

Mailing Address: 15751 Sheridan Street Fort Lauderdale, Fl. 33331 Contact: Rich Jasinski (954) 649-4922

Web Site:

Email:

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

  1. Substitutions: Not permitted.
  2. Requests for substitutions will be considered in accordance with provisions of Section.

2.2 Door Hood and Door Canopy

A. Material: Acrylonitrile-Butadiene-Styrene (ABS) Plastic

B. Mfg. Process: Thermo Molded.

  1. Thickness: Note thicknesses will vary due to the molding process.
  1. Door Hood .187 Nominal Inches. Specify use for mild climates.
  2. Door Canopy .250 Nominal Inches. Specify use for climates with snow and ice.
  1. Colors: Almond, Beige and Gray
  1. Size: 54.5” Wide, 7.5 “ High and 7.5” Deep
  1. Fasteners:
  1. Qty.7 – ELCO #14 – 10X SS4 410 Stainless Steel 1 3/4″ Concrete or MasonryAnchorswith Stalgard Coating for Additional Corrosion Resistance.Miami Dade County Product Control Approved and Made in USA
  2. Qty. 7 – 1/4″ x 1″ Neopreme Bonded Stainless Steel Washers Made in USA

PART 3EXECUTION

3.1 EXAMINATION

  1. Contractor to thoroughly inspect product prior to installation for any visual evidence of damage or defect. If either is present, contact manufacturer.

3.2 IMPORTANT SAFETY PRECAUTIONS

A. As with all cutting tools and fasteners, normal safety precautions should be observed when drilling holes to avoid electrical installations, other utilities and reinforcement bars. Careful use will provide the utmost in safety and reliability. The wearing of safety goggles by users and persons in the vicinity is required by Federal Law.

3.3. INSTALLATION

  1. Use the Door Hood or HD Door Canopy as a template centered horizontally above door or window approx.6” past each side and vertically 2” above open door.
  2. Mark all holes and remove product.
  3. Crete-Flex SS4 Concrete Fasteners and stainless steel bonded washer are included and can also be installed with a traditional 1000 or Crete-Flex installation tool.For masonry or concrete installations, drill holes with a commercial-grade hammer drill or rotary hammer using a 7/32” ANSI masonry bit.

1. Choose an appropriate stainless steel fastener and use the included stainless steel bonded washer for all other substrates.

  1. Mount the Door Hood or HD Door Canopy leaving approximately ½” space between the wall and mounting flange. Apply caulking between the wall and the Door Hood or HD Door Canopy mounting flange. Tighten fasteners gently against the wall. Being carefull not to over tighten and crack the Door Hood or HD Door Canopy mounting flange.

3.4 PAINTING

A. DOORBRIM products can be painted any custom color with latex enamel paint.

** NOTE TO SPECIFIER ** Specify provisions for protecting work after installation but prior to acceptance by Owner. Coordinate article below with Division 1 Execution Requirements Section.

3.4 PROTECTION

  1. Protect installed work from damage due to subsequent construction activity on the site.

END OF SECTION

08 720-1