[SUBMITTAL INFORMATION]

DESIGN A/E NOTE - GUIDE SPECIFICATION CONVENTIONS

Color-highlighted text

Yellow: Editor’s Notes. Comments inserted into the text are addressed to the A/E, not the Contractor. Editor’s Notes are formatted as hidden text. Editor’s Notes are not identified with an update. Do not print Editor’s Notes in issue for distribution to Bidders/Contractors.

Tip: To not print Editor’s Notes (hidden text) in document choose Tools on Menu bar, click Options, Print tab, under Include with document, uncheck Hidden text (check to print text), click OK. Save.

Tip: To view Editor’s Notes (hidden text) in a document choose Tools on Menu bar, click Options, View tab, under Formatting marks, check Hidden text (uncheck to hide text), click OK. Save.

Red: Text updated in 1st quarter. April – June.

Strikethrough text and highlighting (not text) in previously issued quarters are deleted. Only 1st quarter highlighted updated text is indicated.

Turquoise: Text updated in 2nd quarter. July – September.

1st quarter updated text remains highlighted.

Pink: Text updated in 3rd quarter. October – December.

1st and 2nd quarter updated text remain highlighted.

Bright Green: Text updated in 4th quarter. January – March.

1st, 2nd and 3rd quarter updated text remains highlighted.

Text Editing

Select options [in brackets] and edit <notes> before issuing specifications for distribution to Bidders/Contractors.

Delete Strikethrough text.

Tip: To delete strikethrough text, choose Edit on Menu bar, click Find, Find tab, More (Search Options opens), select All, click Format, Font, check Strikethrough, OK.

Click Replace tab, Replace All, OK, Close. Save.

Delete all highlighting of text from issue to be distributed to Bidders/Contractors.

Tip: To delete highlighting, locate cursor at beginning of Section and block all text in Section, press Shift + Control + End, click No Highlight icon on Formatting toolbar. Save.

IMPORTANT: Retain month and year under section title on first page indicating updated Guide Specification Section issue used.

Note: This page will not print when Hidden text is unchecked as indicated in Editor’s Notes Tip.

IF THE HIDDEN GUIDE SPECIFICATION CONVENTIONS DO NOT APPEAR PRECEEDING THIS

NOTE, TURN THEM ON AS FOLLOWS.

FOR MICROSOFT WORD 2000 and 2003, CLICK ON SHOW/HIDE ICON IN MENU BAR OR CHOOSE

TOOLS IN MENU BAR. THEN CLICK OPTIONS, VIEW TAB, UNDER FORMATTING MARKS, CHECK

HIDDEN TEXT.

FOR MICROSOFT WORD 2007, CLICK ON MICROSOFT OFFICE ICON LOCATED IN UPPER LEFT

CORNER OF MENU BAR. CLICK ON WORD OPTIONS AT BOTTOM OF DROP DOWN. THEN CLICK

ON DISPLAY. CHECK THE HIDDEN TEXT BOX.

FOR MICROSOFT OFFICE 2010, CLICK ON FILE BUTTON LOCATED IN UPPER LEFT CORNER OF

MENU BAR. IN THE DROP DOWN, CLICK ON OPTIONS, AND A WORD OPTIONS BOX WILL

APPEAR. CLICK ON DISPLAY. CHECK THE HIDDEN TEXT BOX.

THE GUIDE SPECIFICATION CONVENTIONS SHOULD NOW BE VISIBLE IN THE DOCUMENT.

(Delete this note before printing.)

SECTION 220553

IDENTIFICATION FOR PLUMBING PIPING AND EQUIPMENT

(Edited from DeCA June 2017 Design Criteria)

PART 1 - GENERAL

1.1  SUMMARY

  1. Section Includes:
  2. Nameplates.
  3. Tags.
  4. Stencils.
  5. Pipe Markers.
  6. Related Sections:
  7. Division 01 Section Mechanical, Refrigeration, Food Service Equipment and Electrical Coordination.
  8. Division 01 Section Quality Control.
  9. Division 01 Section Closeout Procedures.

1.2  QUALITY CONTROL

  1. The following publications form a part of this Specification to the extent they are applicable:
  2. Division 01 Section Quality Control.
  3. ASME A13.1 - Scheme for the Identification of Piping Systems.

PART 2 - PRODUCTS

2.1  NAMEPLATES

  1. Description: Laminated three-layer plastic with engraved black letters on light contrasting background color, 4 inch by 1-1/2 inch or larger.

2.2  TAGS

  1. Plastic Tags: Laminated three-layer plastic, brass, or aluminum with engraved black letters on light contrasting background color. Tag size minimum 11/2 inch.
  2. Chart: Typewritten letter size list in anodized aluminum frame.

2.3  PIPE MARKERS

  1. Color: Conform to ASME A13.1.
  2. Plastic Pipe Markers: Factory fabricated, flexible, semi rigid plastic, preformed to fit around pipe or pipe covering; minimum information indicating flow direction arrow and identification of fluid being conveyed.
  3. Plastic Tape Pipe Markers: Flexible, vinyl film tape with pressure sensitive adhesive backing and printed markings.

2.4  STENCILS

  1. Stencils: With clean cut symbols and letters of following size:
  2. Up to 2 Inch Outside Diameter of Insulation or Pipe: 1/2-inch high letters.
  3. 2-1/2 to 6 Inches Outside Diameter of Insulation or Pipe: 1-inch high letters.
  4. Over 6 Inches Outside Diameter of Insulation or Pipe: 1-3/4 inches high letters.
  5. Stencil Paint: As specified in Division 09 Section Painting and Coating, semi-gloss enamel, colors and lettering size conforming to ASME A13.1.

2.5  PIPE MARKERS

  1. Color and Lettering: Conform to ASME A13.1.
  2. Preformed plastic markers.
  3. Factory fabricated, flexible, semi-rigid plastic, preformed to fit around pipe or pipe covering. Larger sizes may have maximum sheet size with spring fastener.
  4. Plastic Tape Pipe Markers:
  5. Flexible, vinyl film tape with pressure sensitive adhesive backing and printed markings.

2.6  CEILING TACKS

  1. Description: Steel with 3/4 inch diameter color coded head.
  2. Color code as follows:
  3. Green - Plumbing equipment or valve.

PART 3 - EXECUTION

3.1  PREPARATION

  1. Degrease and clean surfaces to receive adhesive for identification materials.
  2. Prepare surfaces in accordance with Division 09 Section Painting and Coating for stencil painting.

3.2  INSTALLATION

  1. Install identifying devices after completion of covering and painting.
  2. Install plastic nameplates with corrosiveresistant mechanical fasteners, or adhesive. Apply with sufficient adhesive to ensure permanent adhesion and seal with clear lacquer.
  3. Install tags with corrosion resistant chain.
  4. Apply stencil painting in accordance with Division 09 Section Painting and Coating.
  5. Install plastic pipe markers in accordance with manufacturer's instructions.
  6. Install plastic tape pipe markers complete around pipe in accordance with manufacturer's instructions.
  7. Identify pumps, heat transfer equipment, tanks, and water treatment devices with plastic nameplates. Small devices, such as inline pumps, may be identified with tags.
  8. Identify control panels and major control components outside panels with plastic nameplates.
  9. Identify valves in main and branch piping with tags.
  10. Tag automatic controls, instruments, and relays. Key to control schematic.
  11. Identify piping, concealed or exposed, with plastic pipe markers or plastic tape pipe markers. Delete markers on piping 3/4 inch diameter and smaller. Identify service and flow direction. Install in clear view and align with axis of piping. Locate identification not to exceed 50 feet on straight runs including risers and drops, adjacent to each valve and Tee, at each side of penetration of structure or enclosure, and at each obstruction.
  12. Provide ceiling tacks to locate equipment or dampers above T-bar type panel ceilings. Locate in corner of panel closest to equipment.

END OF SECTION

<Insert project name and location>

<Insert Submittal Date>

IDENTIFICATION FOR PLUMBING PIPING AND EQUIPMENT

220553 - 1