SECTION 08 71 00

DOOR CONTROLS

** NOTE TO SPECIFIER ** LCN Closers an Allegion Brand; Door Controls.
This section is based on the products of LCN Closers an Allegion Brand, which is located at:
11819 N. Pennsylvania St.
Carmel, IN 46032
Toll Free Tel: 877-578-1247
Email: request info ()
Web: us.allegion.com/brands/lcn/Pages/default.aspx
[ Click Here ] for additional information.
LCN is a leading global provider of premium door closers and sets industry standards for quality, durability and innovation.

1 GENERAL

1.1   SECTION INCLUDES

1.1.1   Door Closers.

1.2   RELATED SECTIONS

** NOTE TO SPECIFIER ** Delete any sections below not relevant to this project; add others as required.

1.2.1   Section 05 10 00 - Structural Metal Framing.

1.2.2   Section 06 10 00 - Rough Carpentry.

1.2.3   Section 08 11 00 - Metal Doors and Frames.

1.2.4   Section 08 10 00 - Doors and Frames.

1.2.5   Section 26 05 00 - Common Work Results for Electrical.

1.3   REFERENCES

** NOTE TO SPECIFIER ** Delete references from the list below that are not actually required by the text of the edited section.

1.3.1   ANSI A117.1 - Accessible and Useable Buildings and Facilities.

1.3.2   ANSI A156.4 - Door Controls - Closers.

1.3.3   Underwriters Laboratories (UL). - Fire Resistance Directory.

1.4   SUBMITTALS

1.4.1   Submit under provisions of Section 01 30 00 - Administrative Requirements.

1.4.2   Product Data: Manufacturer's data sheets on each product to be used, including:

1.4.2.1   Preparation instructions and recommendations.

1.4.2.2   Storage and handling requirements and recommendations.

1.4.2.3   Installation methods.

1.4.3   Shop Drawings: Manufacturer's approved shop drawings are required detailing the application of each product specified.

** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.

1.4.4   Selection Samples: For each finish product specified, two full size samples representing manufacturer's full range of available colors and patterns.

1.4.5   Verification Samples: For each finish product specified, two full size samples, representing actual product, color, and patterns.

1.5   QUALITY ASSURANCE

1.5.1   Manufacturer Qualifications: All equipment specified in this section will be provided by a single manufacturer with a minimum of ten (10) years experience manufacturing door hardware.

1.5.2   Installer Qualifications: All products listed in this section are to be installed by a single installer with a minimum of five (5) years demonstrated experience in installing products of the same type and scope as specified.

** NOTE TO SPECIFIER ** Include a mock-up if the project size and/or quality warrant taking such a precaution. The following is one example of how a mock-up on a large project might be specified. When deciding on the extent of the mock-up, consider all the major different types of work on the project.

1.5.3   Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship.

1.5.3.1   Finish areas designated by Architect.

1.5.3.2   Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect.

1.5.3.3   Refinish mock-up area as required to produce acceptable work.

1.6   DELIVERY, STORAGE, AND HANDLING

1.6.1   Store products in manufacturer's unopened packaging until ready for installation.

1.6.2   Store and dispose of solvent-based materials, and materials used with solvent-based materials, in accordance with requirements of local authorities having jurisdiction.

1.7   PROJECT CONDITIONS

1.7.1   Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's absolute limits.

1.8   WARRANTY

1.8.1   At project closeout, provide to the Owner or Owner's Representative an executed copy if the manufacturer's Limited Warranty against Manufacturing Defects.

1.8.1.1   Duration: Ten (10) years.

2 PRODUCTS

2.1   MANUFACTURERS

2.1.1   Acceptable Manufacturer: LCN Closers an Allegion Brand, which is located at: 11819 N. Pennsylvania St.; Carmel, IN 46032; Toll Free Tel: 877-578-1247; Email: ; Web: us.allegion.com/brands/lcn/Pages/default.aspx

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

2.1.2   Substitutions: Not permitted.

2.1.3   Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

** NOTE TO SPECIFIER ** Retain the next Article only if 4000 Series Closers are required. Retain only models specifically required on this project.

2.2   4000 SERIES SURFACE MOUNTED CLOSERS

2.2.1   4010 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.1.1   Mounting: Pull side mount. Handing as noted in the Hardware Schedule.

2.2.1.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.1.3   Arm: Forged steel construction. Opens to 140 degrees. Type and function as noted in the Hardware Schedule.

2.2.2   4010T Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.2.1   Mounting: Pull side mount. Handing as noted in the Hardware Schedule.

2.2.2.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.2.2.3   Arm: Forged steel construction. Maximum opening range from 120 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.3   4020 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.3.1   Mounting: Top jamb, push side mount. Handing as noted in the Hardware Schedule.

2.2.3.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.3.3   Arm: Forged steel construction. Maximum opening range from 140 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.4   4020T Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.4.1   Mounting: Top jamb, pull side mount. Handing as noted in the Hardware Schedule.

2.2.4.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.2.4.3   Arm: Forged steel construction. Maximum opening range from 100 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.5   4030 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements. Finish as noted in the Hardware Schedule.

2.2.5.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.2.5.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.5.3   Arm: Forged steel construction. Maximum opening range from 100 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.6   4030T Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.6.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.2.6.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.6.3   Arm: Forged steel construction. Opens to 180 degrees.

2.2.7   4040 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.7.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.2.7.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.7.3   Arm: Forged steel construction. Maximum opening range from 110 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.8   4040XP Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.8.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.2.8.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.8.3   Arm: Forged steel construction. Maximum opening range from 110 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.9   4040T Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.9.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.2.9.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.9.3   Arm: Forged steel construction. Maximum opening range from 110 to 120 degrees dependent on arm function noted in the Hardware Schedule.

2.2.10   4110 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.10.1   Mounting: Parallel arm mount. Handing as noted in the Hardware Schedule.

2.2.10.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.10.3   Arm: Forged steel construction. Maximum opening range from 110 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.2.11   4110T Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.2.11.1   Mounting: Stop face mount. Handing as noted in the Hardware Schedule.

2.2.11.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.2.11.3   Arm: Forged steel construction. Maximum opening range from 100 to 110 degrees dependent on arm function noted in the Hardware Schedule.

2.2.12   4000T Series Closer: Tested and certified under ANSI A156.4, Grade 1.

2.2.12.1   Mounting: Pull side mount.

2.2.12.2   Cylinder: Cast iron construction, adjustable sizing.

2.2.12.3   Arm: Forged steel construction. Opens to 90 degrees. Type and function as noted in the Hardware Schedule.

** NOTE TO SPECIFIER ** Retain the next Article only if 1000 Series Closers are required. Retain only models specifically required on this project.

2.3   1000 SERIES SURFACE MOUNTED CLOSERS

2.3.1   1260 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.3.1.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.3.1.2   Cylinder: Cast iron construction, adjustable sizing.

2.3.1.3   Arm: Forged steel construction. Maximum opening range from 110 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.3.2   1460 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.3.2.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.3.2.2   Cylinder: Cast iron construction, adjustable sizing.

2.3.2.3   Arm: Forged steel construction. Maximum opening range from 100 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.3.3   1460T Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.3.3.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.3.3.2   Cylinder: Cast iron construction, adjustable sizing.

2.3.3.3   Arm: Forged steel construction. Maximum opening range from 115 to 180 degrees dependent on arm function noted in the Hardware Schedule.

** NOTE TO SPECIFIER ** Retain the next Article only if Concealed Closers are required. Retain only models specifically required on this project and modify the included text as instructed.

2.4   CONCEALED CLOSERS

2.4.1   2010 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.1.1   Mounting: Concealed in frame. Handing as noted in the Hardware Schedule.

2.4.1.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.1.3   Arm: Forged steel construction. Maximum opening range from 110 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.4.2   2030 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.2.1   Mounting: Concealed in 3/4 inch (19mm) tube. Handing as noted in the Hardware Schedule.

2.4.2.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.2.3   Arm: Forged steel construction. Maximum opening range from 110 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.4.3   3030 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.3.1   Mounting: Concealed in door. Handing as noted in the Hardware Schedule.

2.4.3.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.3.3   Arm: Forged steel construction. Maximum opening range from 140 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.4.4   3130 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.4.1   Mounting: Concealed in door. Handing as noted in the Hardware Schedule.

2.4.4.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.4.3   Arm: Forged steel construction. Maximum opening range from 100 to 140 degrees dependent on arm function noted in the Hardware Schedule.

2.4.5   5010 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.5.1   Mounting: Concealed in frame. Handing as noted in the Hardware Schedule.

2.4.5.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.5.3   Arm: Forged steel construction. Maximum opening range from 100 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.4.6   5030 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.6.1   Mounting: Concealed in 3/4 inch (19mm) tube. Handing as noted in the Hardware Schedule.

2.4.6.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.6.3   Arm: Forged steel construction. Maximum opening range from 140 to 180 degrees dependent on arm function noted in the Hardware Schedule.

2.4.7   6030 Series Closer: Tested and certified under ANSI A156.4, Grade 1. Meets ADA requirements.

2.4.7.1   Mounting: Concealed in 3/4 inch (19mm) tube. Non-handed.

2.4.7.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.4.7.3   Arm: Forged steel construction. Maximum opening to 95 degrees.

** NOTE TO SPECIFIER ** Retain the next Article only if Fire/Life Safety Closers are required. Retain only models specifically required on this project and modify the included text as instructed.

2.5   FIRE / LIFE SAFETY CLOSERS

2.5.1   3130SE Series Closer: Tested and certified under ANSI A156.4, Grade 1.

2.5.1.1   Mounting: Concealed in door. Handing as noted in the Hardware Schedule.

2.5.1.2   Cylinder: Cast iron construction. Sizing as noted in the Hardware Schedule.

2.5.1.3   Arm: Forged steel construction. Maximum opening to 110 degrees.

2.5.2   4040SE Series Closer: Tested and certified under ANSI A156.4, Grade 1.

2.5.2.1   Mounting: Non-handed. Positioning as noted in the Hardware Schedule.

2.5.2.2   Cylinder: Cast iron construction, adjustable sizing.

2.5.2.3   Arm: Forged steel construction. Maximum opening range from 95 to 110 degrees dependent on arm function noted in the Hardware Schedule.

2.5.3   2310ME Series Closer: Tested and certified under ANSI A156.4, Grade 1.