Display Hidden Notes to Specifier. (Don't Know How? Click Here) s23

SECTION 09 24 00

PORTLAND CEMENT PLASTERING

Display hidden notes to specifier. (Don't know how? Click Here)

** NOTE TO SPECIFIER ** Vinyl Corp.; beads, trims and control joints for Stucco/Plaster, Drywall, Exterior Insulation Finish Systems (EIFS), and Direct-applied Exterior Finish Systems (DEFS).
.
This section is based on the products of Vinyl Corp., which is located at:
8000 N. W. 79th Pl.
Miami, FL 33166
Toll Free Tel: 800-648-4695
Tel: 305-477-6464
Fax: 305-477-4108
Email: request info ()
Web: www.vinylcorp.com
[ Click Here ] for additional information.
Vinyl Corp. is one of the largest full line vinyl bead and trim manufacturers in the U.S. Product categories include beads, trims and control joints for Stucco/Plaster, Drywall, Exterior Insulation Finish Systems (EIFS), and Direct-applied Exterior Finish Systems (DEFS).The company was formed in 1988 with two extrusion lines, twenty products and approximately six employees. Today the company has over 600 products and 50 employees at the Hialeah, Florida facility. Vinyl Corp. is known in the industry as "Innovators of Vinyl Wall and Ceiling Accessories." Using only virgin vinyl material, they are also #1 in quality!
Why Choose Us? Vinyl Corp. is committed to meeting the most complex challenges in the wall and ceiling industry through innovative product design, exacting manufacturing tolerances, and the most complete selection of accessories in the industry. Through our progressive approach to engineering and manufacturing, we've created innovative accessories and set the quality standard for product excellence. Vinyl Corp. is a division of ClarkDietrich Building Systems, a company that believes peak performance is only achieved if quality is uncompromised every step of the way. We continue to raise the bar through innovative product design, exacting manufacturing tolerances, precise specification and state-of-the-art manufacturing equipment.
In an industry full of choices, why select Vinyl Corp. for your vinyl wall and ceiling accessories?
We use only lead-free, virgin vinyl compounds
- All of our exterior products meet ASTM D-1784, and are designed for application, performance and reliability.
- All of our interior products meet ASTM C-1047, providing durability and impact resistance.
- All of our interior products, pass ASTM E-84 Steiner Smoke and Fire Spread Tests.
- All our products are impervious to rust, corrosion and are electrolysis free.
- They are not damaged by masonry cement additives, magnesium oxychloride cements or calcium chloride additives.
Lead-free virgin vinyl accessories from Vinyl Corp. Why would you choose anything else?

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Interior Portland cement plasterwork and accessories.

B. Exterior Portland cement plasterwork (stucco) and accessories.

1.2 RELATED SECTIONS

A. Section 05 40 00 - Cold-Formed Metal Framing.

B. Section 06 10 00 - Rough Carpentry.

C. Section 06 16 36 - Wood Panel Product Sheathing.

D. Section 07 21 26 - Blown Insulation.

E. Section 09 22 00 - Supports for Plaster and Gypsum Board.

1.3 REFERENCES

A. ASTM International (ASTM):

1. ASTM A 641/A 641M - Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire.

2. ASTM A 653/A 653M - HYPERLINK "http://www.astm.org/Standards/A653.htm"Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process.

3. ASTM B 69 - Standard Specification for Rolled Zinc.

4. ASTM C 91 - Standard Specification for Masonry Cement.

5. ASTM C 150 - Standard Specification for Portland Cement.

6. ASTM C 206 - Standard Specification for Finishing Hydrated Lime.

7. ASTM C 207 - Standard Specification for Hydrated Lime for Masonry Purposes.

8. ASTM C 665 - Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light Frame Construction and Manufactured Housing.

9. ASTM C 847 - Standard Specification for Metal Lath.

10. ASTM C 897 - Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters.

11. ASTM C 926 - Standard Specification for Application of Portland Cement-Based Plaster.

12. ASTM C 932 - Standard Specification for Surface-Applied Bonding Compounds for Exterior Plastering.

13. ASTM C 933 - Standard Specification for Welded Wire Lath.

14. ASTM C 954 - Standard Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness.

15. ASTM C 1002 - Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs.

16. ASTM C 1047 - Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base.

17. ASTM C 1063 - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster.

18. ASTM C 1328 - Standard Specification for Plastic (Stucco) Cement.

19. ASTM D 1784 - Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds.

20. ASTM E 90 - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements.

21. ASTM E 119 - Standard Test Methods for Fire Tests of Building Construction and Materials.

22. ASTM E 413 - Classification for Rating Sound Insulation.

1.4 SUBMITTALS

A. Submit under provisions of Section 01 30 00 - Administrative Requirements.

B. Product Data: Manufacturer's data sheets on each product to be used, including:

1. Preparation instructions and recommendations.

2. Storage and handling requirements and recommendations.

3. Installation methods.

C. Shop Drawings: Show locations and installation of control and expansion joints including plans, elevations, sections, details of components, and attachments to other work, based on architectural drawings.

** NOTE TO SPECIFIER ** Delete selection samples if colors have already been selected.

D. Selection Samples: For each finish product specified, two complete sets of color chips representing manufacturer's full range of available colors and patterns.

E. Verification Samples: For each finish product specified, two samples, minimum size 6 inches (150 mm) square, representing actual product, color, and patterns.

** NOTE TO SPECIFIER ** Delete if not required.

F. LEED Submittals:

1. Product Data for Credit MR 4.1and Credit MR 4.2: For products having recycled content, documentation indicating percentages by weight of postconsumer and preconsumer recycled content. Include statement indicating cost for each product having recycled content. MR 4.1 and MR 4.2 excludes products fabricated from rigid PVC or CPVC plastic.

2. Product Data for Credit MR 2.1 and Credit MR 2.2: For products diverted from disposal in landfills and incinerators, and where recycled resources are directed back to the manufacturing process. Include statement indicating percentage of materials diverted and recycled, and the costs associated with each. MR 2.1 and MR 2.2 excludes products fabricated from rigid PVC or CPVC plastic.

3. Product Data for Credit MR 5: For products where product manufacturing is within a 500 mile radius of the jobsite and the point of extraction of the raw materials. Include a statement indicating the location and distances for the manufacturing plant and the point of extraction of raw materials in relation to the jobsite location.

4. Product Data for Credit IEQ 4.1: For sealants, documentation including printed statement of VOC content.

5. Laboratory Test Reports for Credit IEQ 4: For sealants, documentation indicating that products comply with the testing and product requirements of the California Department of Health Services' "Standard Practice for the Testing of Volatile Organic Emissions from Various Sources Using Small-Scale Environmental Chambers".

1.5 QUALITY ASSURANCE

A. Installer Qualifications: Experienced installer of lathing and plastering systems with familiarity with manufacturer's products scheduled for the Work.

B. Fire-Resistance Ratings: Where indicated, provide Portland cement plaster assemblies identical to those of assemblies tested for fire resistance per ASTM E 119 by, and displaying a classification label from, a qualified independent testing agency acceptable to the authority having jurisdiction. Identify products with appropriate markings of applicable testing agency.

1. Construct fire-resistance rated partitions in compliance with tested assembly requirements indicated on drawings.

2. Rated assemblies shall be substantiated from applicable testing using proposed products, by Contractor.

3. Both metal framing and wallboard manufacturers shall submit written confirmation that it accepts the other manufacturer's product as a suitable component in the assembly. Acceptance is as follows:

a. If installation of both products is proper, no adverse effect will result in the performance of one manufacturer's product by the other's product.

b. Combining products can be substantiated by required assembly tests.

4. Indicate design designations from UL's "Fire Resistance Directory" or from the listings of another qualified testing agency.

C. Sound-Transmission Characteristics: Where indicated, provide Portland cement plaster assemblies identical to those of assemblies tested for STC ratings per ASTM E 90 and classified according to ASTM E 413 by a qualified testing agency.

D. Mockups: Before plastering, install mockups of at least 100 sf (9.3 sq. m) in surface area to demonstrate aesthetic effects and set quality standards for materials and execution.

1. Install mockups for each type of finish indicated.

2. For interior plasterwork, simulate finished lighting conditions for review of mockups.

3. Approved mockups may become part of the completed Work if undisturbed at time of Substantial Completion.

E. Preinstallation Conference: Conduct conference at Project site.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Store materials inside under cover and keep them dry and protected against damage from weather, direct sunlight, surface contamination, corrosion, construction traffic, and other causes.

B. Protect cold-formed metal framing from corrosion, deformation, and other damage during delivery, storage, and handling as required by AISI's "Code of Standard Practice".

1.7 PROJECT CONDITIONS

A. Comply with ASTM C 926 requirements.

B. Interior Plasterwork: Maintain room temperatures at greater than 40 degree F (4.4 degree C) for at least 48 hours before plaster application, and continuously during and after application.

1. Avoid conditions that result in plaster drying out during curing period. Distribute heat evenly; prevent concentrated or uneven heat on plaster.

2. Ventilate building spaces as required to remove water in excess of that required for hydrating plaster in a manner that prevents drafts of air from contacting surfaces during plaster application and until plaster is dry.

C. Exterior Plasterwork:

1. Apply and cure plaster to prevent plaster drying out during curing period. Use procedures required by climatic conditions, including moist curing, providing coverings, and providing barriers to deflect sunlight and wind.

2. Apply plaster when ambient temperature is greater than 40 degree F (4.4 degree C).

3. Protect plaster coats from freezing for not less than 48 hours after set of plaster coat has occurred.

D. Factory-Prepared Finishes: Comply with manufacturer's written recommendations for environmental conditions for applying finishes.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Vinyl Corp., which is located at: 8000 N. W. 79th Pl.; Miami, FL 33166; Toll Free Tel: 800-648-4695; Tel: 305-477-6464; Fax: 305-477-4108; Email: request info (); Web: www.vinylcorp.com

** NOTE TO SPECIFIER ** Delete one of the following two paragraphs; coordinate with requirements of Division 1 section on product options and substitutions.

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01 60 00 - Product Requirements.

2.2 MATERIALS

A. Accessories for Gypsum Wallboard and Gypsum Veneer Base: ASTM C 1047.

B. Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster: ASTM C 1063.

C. Rigid Poly (Vinyl Chloride) (PVC) Compounds and Chlorinated Poly (Vinyl Chloride) (CPVC) Compounds: ASTM D 1784.

2.3 METAL LATH

A. Expanded-Metal Lath: ASTM C 847, cold-rolled carbon steel sheet, ASTM A 653/A 653M, G60 (Z180).

1. Basis-of-Design Product: ClarkDietrich Building Systems.

B. Wire Lath: ASTM C933, Class 1 Galvanized Coating complying with ASTM A 641.

1. Basis-of-Design Product: Structa Wire Corp. products by ClarkDietrich Building Systems.

2.4 ACCESSORIES

** NOTE TO SPECIFIER ** Delete if not required.

A. Plastic Accessories for Gypsum Wallboard and Gypsum Veneer Base: ASTM C 1047. Fabricated from plastic or plastic and paper in combination shall be manufactured from rigid PVC, ABS, PETG, high-impact polystyrene (HIPS), or polycarbonate (PC) plastic not less than 0.028 inch (0.7112 mm) and Section 4.3.1 PVC specification D 1784 Cell class 13244C.

1. Basis-of-Design Product: Vinyl Corp.

** NOTE TO SPECIFIER ** Delete products not required.

2. Corner Beads:

a. Vinyl Corp. "VLCB".

b. Vinyl Corp. "VBCB".

3. Channel Reveals: PVC reveals conforming to ASTM C 1047.

a. Vinyl Corp. "DC-Series".

4. Soffit Vents: Vinyl soffit vent.

a. Vinyl Corp. "DCV-Series".

5. Control Joints:

a. Vinyl Corp. "CJV-Series".

** NOTE TO SPECIFIER ** Delete if not required.

B. Plastic Accessories for Exterior Stucco: ASTM C 1063. Fabricated from plastic or plastic and paper in combination shall be manufactured from rigid PVC, ABS, PETG, high-impact polystyrene (HIPS), or polycarbonate (PC) plastic. Section 4.3.1 PVC specification D 1784 Cell class 13244C.

1. Basis-of-Design Product: Vinyl Corp.

2. Corner Beads:

a. Vinyl Corp. "#1 Series".

** NOTE TO SPECIFIER ** Delete products not required.

3. Casing Beads:

a. Vinyl Corp. "66-Series".

4. Control Joints:

a. Vinyl Corp. "15-Series".

5. Soffit Vents:

a. Vinyl Corp. "V-Series".

b. Vinyl Corp. "CS-V Series".

6. Channel Reveals:

a. Vinyl Corp: "CS Series".

7. Weep Screed:

a. Vinyl Corp. "WS- Series".

C. Metal Accessories: Comply with ASTM A 653/A 653M, G60 (Z180).

1. Basis-of-Design Product: ClarkDietrich Building Systems.

D. Zinc Accessories for Portland Cement Base Plaster. ASTM B 69. Fabricated from Zinc Alloy (99 percent pure zinc).