Communication and Navigation Aids Solic No.: Mll-16-T65-0002

USNS MARY SEARS

T-AGS 65

COMMUNICATION AND NAVIGATION AIDS SOLIC NO.: MLL-16-T65-0002

ITEM NUMBER 0402 CATEGORY "A" 20 September 2016

REV X

MOVE TWO ANTENNAS & UPDATE DRAWINGS USMMI/MLL/MWS

1.0ABSTRACT:

1.1This requirement is to relocate two GMDSS and one SSAS antennason the main mast and update antenna surveys and drawings.

2.0REFERENCES/ENCLOSURES:

2.1References:

2.1.1GMDSS Technical Manual (available onboard)

2.1.2SSAS Technical Manual (available onboard)

2.2Enclosures:

2.2.1MSC N6 Antenna Relocation Sketch

2.2.2MSC Drawing 440-8384762 Antenna Arrangement

3.0ITEM LOCATION/DESCRIPTION:

3.1Description/Manufacturers Data:

3.1.1Ship’s Sailor GMDSS Antennas

3.1.2Ships Security Alarm System

3.2Locations:

3.2.1Antennas are located on the Aft Crow’s Nest Fiberglass Handrails

4.0GOVERNMENT FURNISHED MATERIAL:

4.1MLL Furnished Equipment (MLLFE): None

4.2MLL Furnished Material (MLLFM): None

4.3 MLL Furnished Services (MLLFS):

4.4MLL Furnished Information (MLLFI):None

5.0NOTES:

5.1The contractor and all subcontractors, regardless of tier, must consult the General Technical Requirements (GTR’s), to determine applicability to this work item. In performance of this work item, the contractor and all subcontractors regardless of tier must comply with the requirements of all applicable GTR’s (http//

5.2The contractor and all subcontractors regardless of tier are advised to review other work items under MLL’s contract to determine their effect on the work required under this work item.

6.0QUALITY ASSURANCE REQUIREMENTS:

6.1None

7.0STATEMENT OF WORK REQUIRED:

7.1ARRANGEMENTS: Thecontractor shall provide all labor, material, staging, tools and a qualified electronic technician in 7.5to supervise and direct all labor, to disconnect the two GMDSS and one SSAS antennas, unmount them from the crow’s nest hand rail, reinstall the antennas on the fiberglass diving boards in accordance with MSC N6 Antenna Relocation Sketch,enclosure 2.2.1, install and reconnect new cable from the GMDSS and SSAS system to the antennas.

7.1.1The Contractor shall provide, rig and remove staging toaccomplish this work item.

7.2TESTS AND INSPECTIONS: The qualified electronic technician in 7.5shall furnish all special tools and test equipment required,recalibrate and perform all operationally tests, and demonstrate proper operation of the GMDSS and SSAS to the Radio Officer and Second Mate.

7.3PREPARATION OF DRAWINGS: The qualified electronic technician in 7.5 shall update the Antenna Arrangement Drawing, reference 2.2.2. The Contractor is to provide one hard copy and one electronic and 3 hard copies of the revised drawing in AutoCAD and PDF format.

7.4REPORTS: The qualified electronic technician in 7.5shall provide reports to the chief engineer and the port engineer.

7.4.1Submit a as found conditions report detailing as soon as inspections are complete, measurements are taken and condition observed along with recommended repairs if any needed to be accomplished. Additional repair deemed necessary by the PE shall be the subject of a change order.

7.4.2Submit a a service report,one electronic copy and two (02) typed copies when all work is complete. Report shall consist of all repairs accomplished to include but not limited to, all released dimensional readings, pictures, test data and reports by others and list of all the parts replaced as applicable.

7.4.3The service report shall be endorsed by Contractor QA, Project Officer,

Subcontractor, Port Engineer, and attending Regulatory Agency.

7.5The contractor shall provide a qualified electronic technician. Source information:

Mid Atlantic Engineering Technical Services, Incorporated

POC: Danny Henderson, PMP

1501 Crossways Boulevard, Suite E

Chesapeake, Virginia 23320

Office: 757.512.6883

Cell: 757.777.4721

Fax: 757.410.0100

Email:

Website:

8.0GENERAL REQUIREMENTS: None

VR16-0020

0402 - 1