World’s Finest Automotive Bra Installation Instructions: Dodge Viper SRT-10(2003-2005)
Included Parts – Two (2) Universal Sided FasTrak Mounting Brackets
Required tools – Screwdriver – Phillips #2 (medium tip) stubby
Pre-Installation
1)Carefully read and follow instructions, to ensure optimal installation and performance.
2)Thoroughly wash & wax vehicle surfaces, including inside wheel wells and under front bumper, to prevent entrapment of moisture and/or debris between paint finish and .SpeedLingerieTM
3)Place vehicle and unfolded SpeedLingerieTM in direct sunlight, or near (but not in direct contact with) any radiant heat source for at least 30 minutes to make it more flexible and easier to install.
4)Orient yourself with SpeedLingerieTM. Notice placement of logo window at top center of SpeedLingerieTM.
5)Turn steering wheel completely to passenger side, for easier access to driver side wheel-well.
FasTrakTM Bracket Installation
1)At driver side inner front wheel well, use the Phillips screwdriver to LOOSEN 2 screws, with 5 counter clockwise turns. DO NOT FULLY EXTRACT SCREWS!! Remove protective coating from both sides of both FasTrakTM brackets.
2)Install a FasTrak bracket between wheel well surface and screws, tab end down, unslotted edge facing INWARD. Securely fasten wheel well screws.
3)Turn steering wheel completely to driver side, for easier access to passenger side wheel-well.
4)At passenger side inner front wheel well, repeat Step #1 and #2.
SpeedLingerieTMInstallation
1)Pull hood latch; raise hood.
2)Facing the vehicle, hold properly oriented SpeedLingerieTM outstretched in front of you. Loosely drape SpeedLingerieTMover nose of vehicle.
3)At passenger side, run your thumb through length of QuiKlipTM to “open it up” slightly. This will make it easier to fasten QuiKlipTM onto FasTrak bracket. NOTE! Enfold (using a key or credit card) 5-inch quick release strap within QuiKlipTM. This ensures easy removal of SpeedLingerieTM. Do not pull on this strap during installation.
4)Start at the top of the center section (3 sections total) ofQuiKlipTM and work downward. Fasten the center and bottom sections onto the FasTrak bracket. Do not yet attach the top section of QuiKlipTM.
5)At bottom edge, under the center mesh, and on the inside of SpeedLingerieTM , locate two (2) tailored flaps. These attach to “crossbow” in front grill. Attach the QuiKlipTM at end of the flaps, onto rear edge of bottom “crossbow” duct.
6)Turn steering wheel completely to passenger side, for easier access to driver side wheel well.
7)NOTE! Due to the perfectly tailored fit of SpeedLingerieTM, step #7 takes careful effort. Acquire assistance, to provide “slack” from the front-end midpoint. Do not pull on the QuiKlipTM/stitching itself. Do not pull from the top edge. Installation becomes easier with repeated use.
8)Working from the passenger side across, carefully but firmly stretch SpeedLingerieTMtowards driver side. Gather 6-8” of material at QuiKlipTMin your hands, and carefully but firmly pull from midpoint (side marker level) and lower corner (spoiler level). Repeat steps #2 - 4 to fasten QuiKlipTMon driver side FasTrak bracket.
9)At hood area, gently pull entire top edge of SpeedLingerieTM to align the hood emblem lie just inside ridge at top of fan shroud. Flip the top edge over onto itself and attach the QuiKlipTM to the body edge.
10)Notice location of the hood latch on hood underside. To close hood, place palms of hands directly over the latch and press down firmly and evenly.
Mirror Cover Installation
1)To differentiate between passenger and driver side mirror cover, the vinyl covered loop portion of the hook & loop fastener folds down and over the hooked portion.
2)Lower/open windows. Close doors. Enjoy the opportunity to work with your car and take your time.
3)Begin at passenger side. Open the hook & loop tab.
4)Stretch out mirror cover tension cord and slip the cover over the mirror head. NOTE! Support the mirror head properly during installation by.
5)Form the mirror cover into place using both hands and temporarily fasten the hook and loop tab. NOTE! Refer to Pre-installation Step #1 if you are unsure whether you are installing the appropriate mirror cover on the correct side.
6)With both hands, continue forming the mirror cover into place (like molding clay). Adjust material around face of mirror until mirror-opening edges at tension cord align and meet. You may need to open/close hook & loop tab several times during this process.
7)Repeat Steps 2 – 5 at driver side.
Final Adjustment
1)Adjust SpeedLingerieTM where necessary, to assure proper fit.
2)For full effect of SpeedLingerieTM design and glove-like fit, allow 72 hours for material(s) to relax and conform to vehicle’s curves.
3)Park in a warm sunny spot with SpeedLingerieTM on for a few days, to help the process.
4)Apply a quality vinyl conditioner to SpeedLingerieTM if you so desire.
To Remove SpeedLingerieTM
1)Reverse the installation process.
Care & Maintenance
1)For best results, be sure that vehicle surfaces are clean and dry and waxed before installing SpeedLingerieTM.
2)Always inspect SpeedLingerieTM fasteners & surfaces that contact vehicle for possible debris, sand, grit, etc...and remove before installation.
3)Periodically remove SpeedLingerieTM to allow complete aeration of vehicle paint finish and SpeedLingerieTM materials.
4)Remove SpeedLingerieTM before washing vehicle.
5)Remove SpeedLingerieTM after exposure to rain or other moisture/fluids.
6)Clean outer vinyl surfaces of SpeedLingerieTM with a high quality vinyl conditioner during routine car maintenance.
7)Clean felt inner surface with water if necessary, allowing it to dry completely, and brush/vacuum out any remaining particles.
8)To avoid staining or discoloration of SpeedLingerieTM, DO NOT store in direct contact with rubber products (eg. tires, hoses, mats). Vinyl is a porous material that will absorb the black carbon contained with in rubber and result in a stain on the vinyl.
Installation Questions? Call 1(800) 570-1579 for assistance.
Congratulations on your purchase.
SpeedLingerie.
Page 1
rev0704