World S Finest Automotive Bra Installation Instructions Corvette C4 Callaway
World’s Finest Automotive Bra Installation Instructions – Corvette C4 Callaway
Included Parts – Two (2) C4-Callaway FasTrakTM mounting brackets
Required Tools – T-30 Torx socket/screwdriver, Pliers
Pre-Installation
1) Carefully read and follow instructions, to ensure optimal installation and performance.
2) Thoroughly wash & wax vehicle surfaces, including inside wheel wells and under front bumper, to prevent entrapment of moisture and/or debris between paint finish and SpeedLingerieTM
3) Place vehicle and unfolded SpeedLingerieTM in direct sunlight, or near (but not in direct contact with) a radiant heat source for at least 30 minutes to make SpeedLingerieTM more flexible and easier to install.
4) Turn steering wheel completely to passenger side, for easier access to driver side wheel-well.
5) Open hood.
FasTrakTM Bracket Installation
1) At driver side inner front wheel well, use Torx head screwdriver to LOOSEN 4 screws, with 5 counterclockwise turns. NOTE!! DO NOT FULLY EXTRACT SCREWS. Remove protective coating from all sides of FasTrak brackets.
2) Install a FasTrak bracket between wheel well surface and screws.
a) Notice “spacer strip” attached to one side of each bracket. Install bracket so spacer strip contacts wheel well liner.
b) The bracket must be installed tab end down, unslotted edge facing INWARD.
c) Securely fasten wheel well screws with Torx socket. (Use pliers to hold nuts, if applicable)
3) Turn steering wheel completely to driver side, for easier access to passenger side wheel-well.
4) At passenger side wheel well, repeat Steps #1 and #2.
SpeedLingerieTM Installation
1) Facing vehicle, hold properly oriented SpeedLingerieTM outstretched in front of you.
2) At center of Nose Cover, run your thumb through the two lengths of QuiKlip to “open it up” slightly. This will make it easier to fasten QuiKlip onto fiberglass lip. NOTE! Enfold (using a key or credit card) the 5-inch quick release strap within QuiKlip. This ensures easy removal of SpeedLingerieTM. Do not pull on this strap during installation.
3) Fasten QuiKlip channel onto fiberglass lip, located just in front of hood edge (thru gap with hood open). NOTE! Remove your wristwatch, rings, bracelets, jewelry from your hands to avoid scratching painted surfaces.
4) Repeat step#2 at passenger side.
5) Start at bottom of wheel well and fasten QuiKlip onto FasTrak bracket.
6) Turn steering wheel completely to passenger side, for easier access to driver side wheel well.
7) NOTE! Due to the perfectly tailored fit of SpeedLingerieTM, step #8 takes careful effort. Acquire assistance, to provide “slack” from the front-end midpoint. Do not pull on the QuiKlip /stitching itself. Do not pull from the top edge. Installation becomes easier with repeated use.
8) Working from passenger side across, carefully but firmly stretch SpeedLingerieTM towards driver side. Gather 6-8” of material at QuiKlip in your hands, and carefully but firmly pull from midpoint (side marker level) and lower corner (spoiler level). Repeat steps #4 & 5 to fasten QuiKlip on driver side.
9) Carefully lower hood. Tuck sides of Nose Cover over sides of hood as hood closes.
C4 Mirror Cover Installation
Re-verify your Corvette C4 is equipped WITH or WITHOUT “wind deflector wings” on the mirror heads.
1) GM offered a wind deflector wing or “wing” on the mirror heads for the Corvette C4. This wing is also available as an aftermarket product.
2) The wing is attached to the mirror head. It fills the space between the mirror head and the window. It re-directs air flow over the mirror head, not into the driver’s face.
3) Most C4 Corvettes were built without wind deflector wings.
4) SpeedLingerie offers two different Mirror Cover patterns. The standard pattern fits mirror heads WITHOUT wings. The second pattern fits mirror heads WITH wings.
5) The SpeedLingerie pattern for mirrors WITH wings, features additional material to cover the wing.
Mirror Cover Installation
1) Lower/open the windows.
2) Start on the passenger side. NOTE! One Cover fits the driver side. One Cover fits the pass side.
3) Hold one of the Covers near the pass side mirror, oriented as if you would install it. If it does not look like it is oriented correctly, check out the other mirror cover.
4) The Mirror Cover has two openings. One opening is for the face of the mirror head. The second opening is for the neck of the mirror head where it attaches to the door.
5) Stretch the tension cord, and through the opening for the neck, slip the mirror cover over the mirror head. Slip the cover over the mirror face first, and then over the leading point of the mirror head. NOTE! Support the mirror head properly while you are installing/forming the mirror cover.
6) Form the Cover into place with your hands. NOTE! If you are not sure if you have the correct Mirror Cover on the correct side, refer to step#3.
7) Attach the hook and loop Velcro tabs at the neck of the mirror.
8) Continue working the mirror cover into place (like molding clay) with your hands. Adjust the material around the face of the mirror, so that the edges of the material surround the mirror face evenly. NOTE! Enjoy the opportunity to work with your car and take your time.
9) Repeat steps #4-8 to install the driver side Mirror Cover.
Final Adjustment
1) Adjust SpeedLingerieTM where necessary, to assure proper fit.
2) For full effect of SpeedLingerieTM design and glove-like fit, allow 72 hours for material(s) to relax and conform to vehicle’s curves.
3) Park in a warm sunny spot with SpeedLingerieTM on for a few days, to help the process.
4) Apply a quality vinyl conditioner to the SpeedLingerieTM if you so desire.
Care & Maintenance
1) For best results, be sure that vehicle surfaces are clean and dry before installing SpeedLingerieTM.
2) Always inspect SpeedLingerieTM fasteners & surfaces that contact vehicle for possible debris, sand, grit, etc...and remove before installation.
3) Periodically remove SpeedLingerieTM to allow complete aeration of vehicle paint finish and SpeedLingerieTM materials.
4) Remove SpeedLingerieTM before washing vehicle.
5) Remove SpeedLingerieTM after exposure to rain or other moisture/fluids.
6) Clean outer vinyl surfaces of SpeedLingerieTM with a high quality vinyl conditioner during routine car maintenance.
7) Clean felt inner surface with water if necessary, allowing it to dry completely, and brush/vacuum out any remaining particles.
8) To avoid staining or discoloration of SpeedLingerieTM, DO NOT store in direct contact with rubber products (eg. tires, hoses, mats). Vinyl is a porous material that will absorb the black carbon contained with in rubber and result in a stain on the vinyl.
Installation Questions? Call 1(800) 570-1579 for assistance.
Page 1
rev0403