Tables for Dissolved Oxygen (DO2) Instruments

This attachment contains Microsoft Word versions of the tables found in SectionL.6.

Fill out Tables L-1 and L-2 with specifications of your proposed DO2Instrumentsand include them in the Technical Volume of your proposal. SectionL.6.1.2.1 provides detailed instructions for filling out these tables.

Table L-1

DO2Instrument Compliance Matrix
WithInstrument Specifications in Attachment J-2

Instrument Spec I.D. / Parameter / Units / Parameter Value by Instrument Series / Substantiation
A / B / C / D / E / F
DO2-001 / Minimum value / μmol/kg
DO2-002 / Maximum value / μmol/kg
DO2-003 / Accuracy / %
DO2-004 / Resolution / μmol/kg
DO2-005 / Annual Drift / μmol/kg
DO2-006 / Response Times / Seconds and
% of change
DO2-007 / Sampling Frequency on cabled, open ocean shallow profilers / Hz / N/A / N/A / N/A / N/A / N/A
DO2-008 (threshold)
DO2-009 (objective) / Sampling Frequency other locations / Hz / N/A
INTF-001 / Interface to CTD instrument.
Powered?
Controlled?
Flushed? / Yes/No
Yes/No
Yes/No / N/A / N/A / N/A
INTF-002 (objective) / Interface to CTD instrument
Powered?
Controlled? / Yes/No
Yes/No / N/A / N/A / N/A
Appendix table / Operational depth range / meters to meters
Appendix table / Survivable depth / meters
Appendix table / Inductive modem / Yes/No / N/A / N/A / N/A / N/A / NA / N/A
Appendix table / Battery life at typical sampling frequency / months / N/A / N/A / N/A / N/A
Appendix table / Internal Storage / # of samples / N/A / N/A / N/A / N/A

Table L-2

DO2Instrument Compliance Matrix
With Common Specifications in Attachment J-1

Instrument Spec I.D. / Parameter / Units / Parameter Value by Instrument Series / Substantiation
A / B / C / D / E / F
OPER-001 / Salinity range / PSS
OPER-002 / Temperature range / oC
OPER-003 / Biofouling mitigation measures provided? / Yes/No
OPER-004
(objective) / Biofouling mitigation provides specified accuracy for defined deployment intervals? / Yes/No
OPER-005
(objective) / Maintains calibration within specified accuracy for defined deployment intervals? / Yes/No
OPER-006 / Meets all performance requirements for defined deployment intervals without need for physical maintenance? / Yes/No
OPER-007 / Deployed, recovered, redeployed without performance impairment? / Yes/No
OPER-008
(objective) / Connect to, interface with, be controlled by other instruments / List of shared resources and interface capabilities
MECH-001 / Instrument housing / Materials used / N/A
MECH-002 / Instrument connector / Materials used / N/A
MECH-003
MECH-004
MECH-005 / Electronic housings immersion depth / meters / Use Table L-1 Survivable Depth
MECH-006
(objective) / Anodized contact surfaces? / Yes/No / N/A
ELEC-001
(objective) / Capable of operating in a +/- 50 VDC potential? / Yes/No
(if no, voltage)
ELEC-002
(objective) / Grounding with no connection to seawater? / Yes/No
ELEC-003 / Battery Life / Months / Use Table L-1 Battery Life
ELEC-004 / Returns to defined state upon being depowered and repowered? / Yes/No
ELEC-005 (threshold)
ELEC-006
(objective) / Isolation from seawater / mega ohms
DATA-001 / Provides internal data storage? / Yes/No / N/A / N/A / N/A / N/A / N/A
INTF-001 / Powered by two wire floating voltages? / Yes/No / N/A
INTF-002 / Supply voltage / Volts DC / N/A
INTF-003 / Time Stamping / List the supported capabilities / N/A
INTF-004
(objective) / Internal clock? / Yes/No / N/A
INTF-005 / Synchronize/set clock over the interface? / Yes/No / N/A
INTF-006 / Data rate if over serial interface / bits/sec / N/A
INTF-007
(objective) / User settable data rate over serial interface? / Yes/No
If yes, maximum serial rate / N/A
INTF-008
(objective) / Ethernet interface? / Yes/No
If yes, list the auto-discovery mechanism(s) / N/A
INTF-009 / ACKs command execution including succeed/fail? / Yes/No / N/A
INTF-010 / Communications interface(s) / List the interfaces / N/A
INTF-011 / Remote control and access? / Yes/No / N/A
INTF-012
(objective) / Supports remote firmware installation? / Yes/No / N/A
INTF-013 / All data accessible remotely via communications interface? / Yes/No / N/A
INTF-014
(objective) / Supports polled operation? / Yes/No / N/A
Supports asynchronous mode operation? / Yes/No / N/A
INTF-015 / Communicate via inductive modem? / Yes/No / N/A / N/A / N/A / N/A / N/A / N/A
COMP-001 / Standards compatibility? / List the standards
SHIP-001 / Containers meet ASTM D4169 Level1? / Yes/No
SHIP-002 / Stored without degradation between -20 and 50°C for 12 months? / Yes/No
(if no, provide temperature or time limitations)
SHIP-003 / External cases labeled with safe handling precautions? / Yes/No / N/A
IDEN-001 / Indelible vendor marking on external surface? / Yes/No / N/A
IDEN-002 / Capable of OOI marking without damage? / Yes/No / N/A
QUAL-001 / Materials used and treated reduce wear, corrosion, and deterioration to allow multiple deployments? / Yes/No
Appendix
(objective) / Uses MCBH connector per table? / Yes/No / N/A
Appendix
(objective) / Water-blocked connector with backup o-ring seal? / Yes/No / N/A

Fill out Table L-3 with the models of your proposed DO2Instruments and include the table in the Technical Volume of your proposal. SectionL.6.1.2.1 provides detailed instructions for filling out this table.

Table L-3

Proposed Models for DO2 Instruments

Instrument Series / Contractor Instrument Model Number or Designation
A
B
C
D
E
F

Fill out Table L-4 and include it in the Past Performance Volume of your proposal. SectionL.6.1.3 provides detailed instructions for filling out this table.

Table L-4.

Past Performance for Each Contract

Effort name
Company Performing the Effort
Contract name
Period of performance / From DD/MM/YYYY to DD/MM/YYYY
Contract value in $
Customer name and address
Technical Point of contact information
(name, phone number, e-mail)
Contractual Point of contact information
(name, phone number, e-mail)
(extend as necessary)

Ver 0-04Page 1 of 5