Stormpluz IZ3 Clad Ultimate Double Hung (Obsolete Product)

Part 1 General

1.1Section Includes

A.Aluminum CladUltimate Double Hung, Single Hung, Transom, Picture window complete with hardware, glazing, weather strip, insect screen, removable grille, simulated divided lite, jamb extension, combination storm/screen, interior shade, and standard or specified anchors, trim, attachments, and accessories

1.2Related Sections

A.Section 01 33 23 – Submittal Procedures; Shop Drawings, Product Data and Samples

B.Section 01 62 00 – Product Options

C.Section 01 65 00 – Product Delivery

D.Section 01 66 00 – Storage and Handling Requirements

E.Section 01 71 00 – Examination and Preparation

F.Section 01 73 00 - Execution

G.Section 01 74 00 – Cleaning and Waste Management

H.Section 01 76 00 – Protecting Installed Construction

I.Section 06 22 00 – Millwork: Wood trim other than furnished by window manufacturer

J.Section 07 92 00 – Joint Sealant: Sill sealant and perimeter caulking

K.Section 09 90 00 – Painting and Coasting: Paint and stain other than factory-applied finish

1.3References

A.American Society for Testing Materials (ASTM):

1.E283: Standard Test method for Rate of Air Leakage through Exterior Windows, Curtain Walls and Doors

2.E330: Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls and Door by Uniform Static Air Pressure Difference

3.E547: Standard Test Method for Water Penetration of Exterior Windows, Curtain Walls and Doors by Cyclic Static Air Pressure Differential

4.E2190: Specification for Sealed Insulated Glass Units

5.C1036: Standard Specification for Flat Glass

6.E2068: Standard Test Method for Determination of Operating Force of Sliding Windows and Doors

7.E1996: Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials

8.E1886: Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials

B.American Architectural Manufacturer’s Association/Window and Door Manufacturer’s Association (AAMA/WDMA/CSA):

1.AAMA/WDMA/CSA 101/I.S.2/A440-08, North American Fenestration, Standard/Specification for windows, doors and skylights

2.AAMA/WDMA/CSA 101/I.S.2/A440-11, NAFS 2011 – North American Fenestration, Standard/Specification for windows, doors and skylights

C.WDMA I.S.4: Industry Standard for Water Repellant Preservative Treatment for Millwork

D.Window and Door Manufacturer’s Association (WDMA): 101/I.S.2 WDMA Hallmark Certification Program

E.Sealed Insulating Glass Manufacturer’s Association/Insulating Glass Certification Council (SIGMA/IGCC)

F.American Architectural Manufacturer’s Association (AAMA): 2605: Voluntary Specification for High Performance Organic Coatings on Architectural Extrusions and Panels

G.National Fenestration rating Council (NFRC):

1.101: Procedure for Determining Fenestration Product thermal Properties

2.200: Procedure for Determining Solar Heat Gain Coefficients at Normal Incidence

H.Window covering Manufacturer’s Association

1.A100.1: Standard for safety of corded covering products

1.4System Description

A.Design and Performance Requirements:

1.Window units shall be designed to comply with ASTM E1996 Wind Zone 3 Missile Level D Rating: +55/-65psf

2.Impact and Cycling per ASTM E1996 and E1886 with passing results for Missile Level D and Pressure Cycling of +55/-65psf

3.Air leakage shall not exceed the following when tested at 1.57 psf according to ASMT E283: 0.30 cfm per square foot of frame

4.No water penetration when tested at the following pressure according to ASTM E547: 8.25 psf

5.Assembly shall withstand a positive or negative uniform static air pressure difference of +82.5/-97.5 psf without damage when tested according to ASTM E330

1.5Submittals

A.Shop Drawings: Submit shop drawings under provision of Section 01 33 23

B.Protect Data: Submit catalog data under provision of Section 01 33 23

C.Samples:

1.Submit corner section under provision of section 01 33 23

2.Include glazing system, quality of construction and specified finish

D.Quality Control Submittals: Certificates: submit manufacturer’s certification indicating compliance with specified performance and design requirement under provision of section 01 33 23

1.6Quality Assurance

A.Requirements: consult local code for IBC [International Building Code] and IRC [International Residential Code] adoption year and pertinent revisions for information on:

1.Egress, emergency escape and rescue requirements

2.Basement window requirements

3.Windows fall prevention and/or window opening control device requirements

1.7Delivery

A.Comply with provisions of Section 01 65 00

B.Deliver in original packaging and protect from weather

1.8Storage and Handling

A.Prime and seal wood surfaces, including to be concealed by wall construction, if more than thirty (30) days will expire between delivery and installation

B.Store window units in an upright position in a clean and dry storage area above ground to protect from weather under provision of Section 016600

1.9Warranty

Complete and current warranty information is available at marvin.com/warranty. The following summary is subject to the terms, condition, limitations and exclusions set forth in the Marvin Windows and Door Limited Warranty and Products in Coastal Environments Limited Warranty Supplement:

A.Clear insulating glass with stainless steel spacers is warranted against seal failure caused by manufacturing defects and resulting in visible obstruction through the glass for twenty (20) years from the original date of purchase. Glass is warranted against stress cracks caused by manufacturing defects from ten (10) years from the original date of purchase.

B.Standard exterior aluminum cladding finish is warranted against manufacturing defects resulting in chalk, fade and loss of adhesion (peel) per the American Manufacture’s Association’s (AAMA) Specification 2605-11 Section 8.4 and 8.9 for twenty (20) years from the original date of purchase.

C.Factory applied interior finish is warranted to be free from finish defects for a period of five (5) years from the original date of purchase.

D.Hardware and other non-glass components are warranted to be free from manufacturing defects for ten (10) years from the original date of purchase.

2

Part 2 Products

2.1Manufactured Units

A.Description: Aluminum clad Ultimate Double Hung (and related stationary units) as manufactured by Marvin Windows and Doors, Warroad, Minnesota.

2.2Frame Description

A.Interior: Non Finger-JointedPine or finger-jointed core with non finger-jointedPine veneer; optional non finger-jointedDouglas Fir or finger-jointed core with non finger-jointedDouglas Fir veneer; optional non finger-jointedWhite Oak or finger-jointed with non finger-jointedOak veneer; non finger-jointedCherry or finger-jointed core with Cherry veneer; non finger-jointedMahogany or finger-jointed core with non finger-jointedMahogany veneer; non finger-jointedVertical Grain Douglas Fir or finger-jointed with non finger-jointedVertical Grain Douglas Fir veneer

1.Kiln-dried to moisture content no greater than 12 percent at the time of fabrication

2.Water repellant, preservative treated in accordance with ANSI/WDMA I.S.4.

B.Frame exterior aluminum clad with 0.050” (1.3mm) thick extruded aluminum

C.Frame thickness:11/16” (17mm) head jamb, 1 11/32” (34mm) composite side jamb

D.Frame depth: Frame depth had an overall 5 21/32” jamb (144mm). 4 9/16” (116mm) jamb depth from the nailing fin plane to the interior face of the frame for new construction.

E.Frame bevel: 8 degree bevel

F.Sill: 1 7/16” (37mm)

2.3Sash Description

A.Interior: Non Finger-JointedPine or finger-jointed core with non finger-jointedPine veneer; optional non finger-jointedDouglas Fir or finger-jointed core with non finger-jointedDouglas Fir veneer; optional non finger-jointedWhite Oak or finger-jointed with non finger-jointedOak veneer; non finger-jointedCherry or finger-jointed core with Cherry veneer; non finger-jointedMahogany or finger-jointed core with non finger-jointedMahogany veneer; non finger-jointedVertical Grain Douglas Fir or finger-jointed with non finger-jointedVertical Grain Douglas Fir veneer

1.Kiln-dried to moisture content no greater than twelve (12) percent at the time of fabrication

2.Water repellant preservative treated with accordance with WDMA I.S.4.

B.Sash exterior aluminum clad with 0.050” (1.3mm) thick extruded aluminum

C.Sash thickness: 1 9/16” (40mm) for operating units, 1 7/8” (48mm) for stationary units. Corner slot and tenoned.

D.Operable sash tilt to interior for cleaning or removal

E.Sash Options: Unequal Sash

F.Interior Sash Sticking

1.Standard is: Ovolo

2.Optional Interior Square sticking

2.4Glazing

A.Select quality complying with ASTM C1036. Insulating glass SIGMA/IGCC certified to performance level CBA when tested in accordance with ASTM E2190.

B.Glazing method: Insulating glass

C.Glazing seal: Silicone bedding on interior, acrylic foam adhesive tape on exterior

D.Glass Type: Clear, Bronze, Gray, Reflective Bronze, Obscure, Laminated,Low E2 with or without Argon, Low E3 with or without Argon,Low E1 with or without Argon

2.5Finish

A.Exterior: Aluminum clad. Fluoropolymer modified acrylic topcoat applied over primer. Meets AAMA 2605 requirements.

1.Aluminum cladColors: Stone White, Bahama Brown, Bronze, Pebble Gray, Evergreen, Sierra White, Coconut Cream, French Vanilla, Cashmere, Desert Beige, Cumulus Gray, Cadet Gray, Ebony, Arctic White, Cascade Blue, Hampton Sage, Wineberry, Bright Silver (pearlescent), Copper (pearlescent)

2.Custom colors: Contact your Marvin representative

B.Interior Finish options:

1.Prime: Factory applied enamel primer. Available on Pine product only.

2.Painted Interior Finish.Available on Pine product only.

3.Factory-applied water-borne acrylic enamel clear coat. Applied in two separate coats with light sanding between coats. Available on Pine, Mahogany,Mixed Grain Douglas Fir, Vertical Grain Douglas Fir, Cherry, White Oak.

4.Factory-applied water-borne urethane stain. Stain applied over a wood (stain) conditioner. A water-borne acrylic enamel clear coat applied in two separate coats, with light sanding between coats, applied over the stain. Available on Pine, Mahogany,Mixed Grain Douglas Fir, Vertical Grain Douglas Fir, Cherry, White Oak. Colors available: Wheat, Honey, Hazelnut, Leather, Cabernet, and Espresso.

2.6Hardware

A.Balance system: Coil spring block and tackle with nylon cord and fiber filled nylon clutch

B.Jamb carrier: Vinyl extrusion with wood and aluminum inserts

1.Color: Beige

C.Lock: High pressure zinc die-cast cam lock and keeper

1.Finish: Phosphate coated and electrostatically painted Satin Taupe, Bronze, White, Plated brass, solid brass

D.Four interior stainless steel storm brackets per units. Two located below check rail and two located at bottom rail to sill location.

2.7Weather Strip

A.Operating units:

1.Continuous, leaf weather strip at head jamb, parting stop, dual durometer bulb at check rail, foam bulb type dual durometer weather strip on vertical sash edge; dual durometer bulb weather strip at bottom rail

B.Stationary units:

1.Continuous, bulb weather strip at perimeter of sash, concealed slotted bulb weather strip on exterior of sash, pile weather strip on interior of blind stop, dual durometer bulb weather strip at bottom rail

2.8Jamb Extension

A.Jamb extensions are available for various wall thickness factory-applied up to a 12” (305mm) wide

B.Finish: Match interior frame finish

2.9Insect Screen

A.Factory-installed full or half screen. Half screen covers sash opening.

1.Screen Mesh: charcoal fiberglass, charcoal aluminum wire, black aluminum wire, bright aluminum wire, bright bronze wire, Hi-Tran fiberglass mesh

B.Aluminum frame finish:

1.Color: Match exterior aluminum clad color

C.Optional Magnum Screen:

1.Extruded aluminum surround with charcoal Hi-Tran fiberglass mesh

2.10Combination Strom Sash and Screen

A.Frame: Exterior extruded aluminum 0.045” (1.1mm) thick

B.Finish: Fluoropolymer modified acrylic topcoat applied over Fluoropolymer primer. Meets AAMA 2605 requirements.

1.Finish: Stone White, Bahama Brown, Bronze, Evergreen, Pebble Gray, Arctic White

C.Hardware: Spring loaded locking pins to hold movable storm panel in position. Heavy metal clips to lock upper and lower storm panels together.

D.Weather strip: Dual durometer weather strip on center cross rail seals against operating panel in closed position.

E.Strom panel: Select quality glass in aluminum frame

1.Frame finish: Standard color: Stone White, Bahama Brown, Bronze, Evergreen, Pebble Gray

F.Insect screen panel:

1.Extruded aluminum surround,

2.Screen cloth: Charcoal fiberglass, Charcoal aluminum wire, Black aluminum wire, Bright aluminum wire, Bright bronze wire, Hi-Tran fiberglass mesh

3.Aluminum frame finish: Bronze, White

2.11Interior Shade

A.Cellular shade is attached to the window with a removable surround system that houses the cellular shade system

1.Minimum jamb depth required 5 13/16” (148mm)

2.Shade cartridge is removable and replaceable

3.Shade control: Top down, bottom up

B.Wood wrapped extruded aluminum cellular shade

1.Single non-fire rated hexagonal honeycomb (cellular) 3/4” (19mm)

2.Semi-opaque fabric (light filtering)

a.Colors: Driftwood, Marigold, Almond, Rose, Denim, Biscuit, Champagne, Moss, Cinnamon, Silver, White, Stone, Tan, Ivory, Eggshell

3.Opaque fabric (blackout)

a.Colors: White, Stone, Tan, Ivory, Eggshell

2.12Removable Interior Grilles

A.3/4” by 15/32” (19mm x 12mm) wide or 1 1/8” x 15/32” (29mm x 12mm) wide – Pine only

1.Pattern: Rectangular, Diamond, Custom lite layout

2.Finish: Match interior sash finish

2.13Simulated Divided Lites (SDL)

A.5/8” (16mm) wide, 7/8” (22mm) wide, 1 1/8” (29mm), 1 ¾” (44mm), 2 13/32” (61mm) wide with or w/out internal spacer bar

B.Exterior muntins: 0.055” (1.4mm) thick extruded aluminum

C.Interior muntins: Pine, Mixed Grain Douglas Fir, White Oak, Cherry, Mahogany,Vertical Grain Douglas Fir

D.Muntins adhere to glass with closed-cell copolymer acrylic foam tape

E.Sticking:

1.Standard:Ovolo

2.Optional: Interior Square Sticking

F.Patterns:Rectangular, diamond, custom lite cut

G.Finish – exterior matched exterior aluminum clad colors, interior matches’ interior wood species and color

2.14Accessories and Trim

A.Installation Accessories:

1.Factory-installed vinyl nailing/drip cap

2.Installation brackets: 6 3/8” (162mm), 9 3/8” (283mm), 15 3/8” (390mm)

3.Masonry brackets: 6” (152mm), 10” (254mm)

B.Aluminum Extrusions:

1.Profile: Brick Mould Casing (BMC), Flatcasing, Columbus Casing, Grayson, Kinsley, Ridgeland Casing, Stratton Casing, Thorton Casing, Potter Casing

2.Aluminum clad Extrusion: Frame Expander, Jamb Extender, Mullion Cover,MullionExpander, Subsill, SubsillEnd Cap and Lineal cap

3.Finish; Fluoropolymer modified acrylic topcoat applied over primer. Meets AAMA 2605 requirements.

4.Available in all exterior aluminum clad colors

3

Part 3 Execution

3.1Examination

A.Verification of Condition: Before installation, verify openings are plumb, square and of proper dimensions as required in Section 01 71 00. Report frame defects or unsuitable conditions to the General contractor before proceeding.

B.Acceptance of Condition: Beginning on installation confirms acceptance of existing conditions

3.2Installation

A.Comply with Section 01 73 00

B.Assemble and install window/door unit(s) according to manufacturer’s instruction and reviewed shop drawing

C.Install sealant and related backing materials at perimeter of unit or assembly in accordance with Section 07 92 00 Joint Sealants. Do not use expansive foam sealant.

D.Install accessory items as required

E.Use finish nails to apply wood trim and mouldings

3.3Cleaning

A.Remove visible labels and adhesive residue according to manufacturer’s instruction

B.Leave windows and glass in a clean condition. Final cleaning as required in Section 01 74 00.

3.4Protecting Installed Construction

A.Comply with Section 07 76 00

B.Protecting windows from damage by chemicals, solvents, paint or other construction operations that may cause damage

End of Section

Doc. 64365 Rev. 10/27/2014 Section 08 52 13 ~ 1 ~ Aluminum Clad Ultimate Double Hung

CHECK MARVIN ONLINE DOCS FOR LATEST VERSION Printed on: 9/22/2018 12:39 PM