Attachment B – Specifications

RFx No. 3000010722Title: Boats and Trailer - LDWF

3 Boats, 1 Trailer as Follows

Motor and Lower Unit Specs

  • Surface Drive Unit: New, Current Model GTR 40 XD-LS or Equal

State Brand/Model Bidding: ______

  • Motor: 40 HP Briggs and Stratton EFI or Equal

State Brand/Model Bidding: ______

  • Displacement: 993 cc
  • Tall Transom
  • Remote Console Steering Ready
  • Forward, Neutral, and Electric Engaged Planetary Reverse from console (operated with outboard style control box/lever with power trim on throttle control)
  • Tachometer & Hour Meter
  • Key and Kill Lanyard
  • Remote Electric Start
  • 4750RPM High Rev coils (protects against over revving)
  • Hydraulic Power Trim
  • Hi-Flow Stainless Steel muffler
  • Aluminum and Stainless Construction
  • 3-piece Billet machine aluminum lower unit with integrated High Thrust Reverse Cavitation Plate
  • 30” Output Propeller Shaft
  • 11” Stainless Hardened 3-blade Weedless Propeller
  • Lifetime Belt Warranty Driven Propeller
  • Gator Grass Camo paint (corrosion resistant) or Equal

State Color Bidding: ______

  • Rigging and Installation of throttle control assembly, cables, fuel lines, and other equipment
  • Marine grade hardware, fittings, and cables (Stainless steel/aluminum) or equivalent
  • Installation of engine, all electrical wiring ran, fused, wrapped, and connected
  • Hydraulic steering installed and tested
  • Engine prepped, started, and test ran

Boat Specs

  • 18’ X 60” Gator Tail Extreme Console Series Boat or Equal
  • 20” sides, 21” transom

Brand/Model Bidding: ______

  • New, Current Model
  • USCG Certified Hull
  • Minimum 5-person capacity rating
  • One Piece 0.125” Thick 5086 H116 Aluminum Hull
  • 2” x 2” Custom Extruded Longitudinal Runners of Marine Grade Aluminum
  • 0.100” Thick Deck and Floor
  • Full Floor, No Gutters
  • 6” 6061T6 Channel for Transom
  • Performance Step Hull Design and Sidewall Crimp
  • Dropdeck Transom
  • Stainless Steel Rivets for Sub-Floor
  • 4’ Front Deck with Hatch & Pedestal Base
  • Under Deck Storage
  • Self-Draining Deck
  • All decks to be flush (or nearly flush) with gunnel
  • 10” Catwalks welded to gunnel on both port and starboard, to run from rear pods to front deck
  • Gun/Rod Trays welded on port and starboard side beneath the Catwalks for Fishing Rod storage
  • Protrude to interior of boat until flush with Catwalks
  • Dual Rear Pods with 17” rear deck between the pods
  • Open under the rear deck
  • Pedestal base installed in the rear deck
  • Stabilizer Kit to include 2 spud poles, sockets, and flat bar mount with Quick Fist Clamps
  • 10’ push pole with flat bar mount and Quick Fist Clamps
  • Center Console Steering Kit with storage shelf and grab bar
  • Console to be mounted 83” from the transom and immediately in front of longitudinal runner
  • Console to include steering helm, wheel, Mercury throttle control, 12V accessory plug, and other marine components
  • Electrical panel on console to have separate switches for Navigation lights, Anchor light, Spotlights, Under gun/rod tray lights, auto/manual bilge, and any other necessary switches
  • Hydraulic Steering System with all hoses, rams, and other components
  • Adjustable pedestal base, swivel camo seat for center console
  • Hydro-Turf installed
  • Gator Grass Camo paint on boat and all other metal components (gun box, hatches, pods, etc.) with Marine treatment to bottom of boator Equal

State Color Bidding: ______

  • 13 gallon fuel tank with gas line, quick connects, and primer bulb installed
  • Bilge pump with hose and auto/manual switch installed
  • Coast Guard approved LED Nav. Lights
  • Waterproof green LED light ropes/bars under gun/rod trays
  • Two Waterproof Rigid Swamp Light (or equivalent) LED spotlights mounted with a bracket on the center of the bow to include the appropriate 2-wire plug connector mounted to the bow
  • Two battery boxes, 2 batteries, battery disconnect, Marine 2-bank battery charger, and all wiring/installation to be waterproof
  • 1 Battery to be wired for the engine and electronics
  • 1 Battery to be wired for the trolling motor with all trolling motor wiring run to the battery at the back of boat
  • All battery components to be installed in rear of boat
  • Windshield on console to be 18” tall with flare on top and partial sides for support
  • Windshield and components to meet Marine Grade standards
  • Trolling Motor Package to include: Quick Release Bracket, battery charger (already listed above), 50Amp circuit breaker & bracket, and marine trolling motor plug/connector in the port bow with wiring run to the rear of the boat for battery power
  • Minn Kota Maxxum 52”, 12V, 55lb thrust, Hand Controlled Trolling Motor or Equal

State Brand/Model Bidding: ______

  • 32” Removable seat (Gun box with storage under hinged lid)
  • Two seating packages to include 11” extension poles for pedestal mounts, swivel mount bases, and camo padded seats
  • Rigging and Installation of cables, wiring, lighting, fuel lines, and all other equipment
  • Marine grade hardware, fittings, and cables (Stainless steel/aluminum) or equivalent
  • Installation of engine, all electrical wiring ran, fused, wrapped, and connected

Trailer Specs

  • Trailer to fit size and weight of Boat above
  • McClain or Equal

State Brand/Model Bidding: ______

  • Heavy Duty Galvanized Single Axle Trailer
  • Adjustable Side Guides
  • 13” Aluminum Wheels with Radial Tires (Including spare tire and wheel)
  • LED Lighting
  • Appropriate coupler and locking pins
  • Trailer Ratchet Straps
  • Dolly Wheel
  • Boat trailer set to the size of the boat

1