List of Equipments / Instruments for use in DHQ Hospital Timergara Dir Lower during the year 2013-14.
S.No / Name of item / Specifications / Qty
1 / Oxygen Concentrator / Dimensions:
28.5 in. high, 15.7 in. wide, 14.5 in. deep
(72.4 cm high, 40.0 cm wide, 36.8 cm deep)
Weight:
54.0 lb; shipping weight - 59.0 lb
(24.5 kg; shipping weight - 29.0 kg)
Electrical
120 VAC, 60 Hz, 4 amps, 350 watts
Requirements:
230 VAC, 50 Hz, 4 amps, 350 watts
Capacity:
5 liters per minute at 90% oxygen
(Based on 70°F [21°C] at sea level)
Accuracy:
Flowmeter ±5% full scale. (Based on
precalibrated analysis.)
Concentration:
1–3 liters per minute at 95% + 0.5/ - 3%
4 liters per minute at 92% + 3.5/ - 3%
5 liters per minute at 90% + 5.5/ - 3%
Response Time:
Allow 5 minutes to attain maximum oxygen
concentration.
Positioning:
Operate the unit in an upright position, maintaining
at least six inches of open space on all sides for
ventilation. / 20
2 / Auto Clave high pressure electric / Large size gase and electrical operatic
3 / ECG Machine / Simultaneous acquisition of 12 channels, and LCD
display.
 Thermal recorder for printing out 12 channels
simultaneously.
 ECG Interpretation Software with over 200 findings forcomplete ECG Analysis reports with measurement data
table should be provided.
 AC as well battery operation.
 Built-in AC interference, noise filter and baseline
Connection / 6
4 / Electric suction machine (heavy duty) / Mobile type Cabinet type, with SS instrument tray
High speed vacuum, vacuum regulator with vacuum gauge,
Max: vacuum 760 mm Hg
Operation with foot switch or front panel capacity 2 x 300 ml bottles Graduated. / 20
5 / Cardiac monitor / Bedside color monitor having 10.4” color display to Monitor ECG, NIBP, Resp., SpO2, having following
High resolution TFT color display
Touch panel monitor control
5 parameters, 4 waveforms.
Smart guide function
Enlarged numeric screen
Alarm indicator
Accurate arrhythmia detection.
Alarm history.
120 hours, 1 trace full disclosure.
Trend graph/trend table. / 05
6 / Cautery Machine
With Disposable cautery leads / RFS-3800K RadioFreq SURG
RFS-3800K (220 240 volts)
Output Voltage :Variable from 500 to 600±20%
Output Power:100w±20%
Output Frequency:3.8 MHz.
Output Waveform:Cut (Fully Filtered)
Cut & Coag (Fully Rectified)
Coag (Partially Rectified)
Fulguration (Spark-Gap)
Accessories:
Neutral Plates
Surgical Electrodes
RF Surgipens
Footswitches / 5 machines
With 500 cautery leads with each machine
7 / Electric Sterilizer / . Instrument sterilizer to have seamless construction
. Should be made of medical grade stainless steel.
. should have thermostatically controlled heating through easily replicable heating through easily
Replaceable heating element of 1 KW
. Size approximately 12 “ L x 6” H
. Should have handles for unit and lid
. The lid to be rigidly constructed to prevent warping hinged to the body and provided with stop to keep it in the upright position.
. The instrument tray to be constructed of stainless steel and fixed with drip handles. / 5
8 / Hydraulic OT Table / Pedestal Type Major Operating Table With 5 Sections.
Table Is Mounted On A Solid Base With Casters And
Locks.
Length Approx 200 cm
Width Approx 50 cm
Height 70 to 100cm
Tilt L/R 20 Deg
Trendelenberg / Reverse Trendelenberg 12 / 25 deg
Table Top Surface Is Fabricated From Radio-
Translucent, Conductive Panels And The Larger Table
Sections Equipped With Radiographic
Cassette Tunnels.
Table should Includes Electro-Hydraulic Controls, Side
Rail Locking System, Kidney Elevator, Grounding
Receptacle And Dual Arm Support Section.
Designed For Use In The Operating Room In A Variety
Of Surgical Procedures.
Complete with Pads and Clamps and Standard
Accessories
Optional Accessories
Kidney Bridge, OrthopaedicAttachement, Eye, neuro
Head Section, Urology attachments, Gynae attachments etc shall be quoted for selection by end user / 2
9 / Anesthesia Machine / Isoflurain/Flu thane/Foraine/ Sevfloraine vaporizer
02/N2O regulators
Self-built ventilator with pulse and BP Monitor
Ban circuit oxygen mask and oxygen regulator breathing bags standard quality
Pressure tube for O2 and N2O
Chimney Piece Head strap/reservoir bag
Mask, L/S , corrugated tube, Air way plastic soda lime, wrench
Mobile trolley, O2 and N2O cylinder / 5
10 / Pulse Oximeter / Pulse oximeter with BP Monitor / 8
11 / Patient Stature (trolley) / Tilting patient’s trolley for use in patient’s recovery
areas.
 Upholstered top with letherite and 3” foam of 2.5
lbs/cft density, with adjustable head 1900 x
600mm, at 890mm high, including 750mm head section, 75mm thick
 Tilting top
 Side rails
 Cylinder cage
 Bumper bar/push handle
 IV pole
 200mm base plate castors
 Safe Working Load 190kg
Local made / 20
12 / Telescope / Aperture 80 mm
Focal Length 900 mm
Focal Ratio f/11
Computer Control - no
1.25" Eyepieces: Focal Lengths 20 mm and 10mm
Magnification Levels: 90x and 45x
Finderscope: Star Pointer
Tripod: Aluminium adjustable
Mount: equatorial
Weight: 24 lbs.
Multi coated optics
Can be used for both terrestrial and astronomical viewingAperture 80mm / 1
13 / Complete TUR P set / Forward-oblique telescope 30 degree,
enlarged view,
Diameter 4mm,
autoclavable, Fiber optic light tran
smission incorporated, color code:
Red
Cystoscope-urethroscope sheath
:
•
Cyst scope Urethroscope- Sheath,
20 Fr with obturator 27026 CO and
2 LUER-Lock connectors, Color Code : Red
•
Cyst scope –Urethroscope- Sheath,
17 Fr, with obturator 27026
UO, and 2 LUER Lock connectors, color code : Yellow.
Deflecting mechanism-telescope Bridges
:
•
Telescope bridge with 2 lockable instrument channel
Optical Forceps
•
Rigid optical Biopsy forceps forward cut with double action jaws.
Flexible Instruments:
•
Forceps for removal of forei
gn bodies, 7 Fr, double action Jaws,
length 40 cm,
•
Ball coagulation electrode, 7 Fr
High frequency cords, Unipolar
:
•
Unipolar High Frequency cord with
4 mm plug for HF unit, Length
300 cm.
Optical Urethrotome:
•
Sheath 21 Fr, for Optical Urethrotome with instrument channel.
•
Obturator for the above mentioned sheath.
•
Supplementary Sheath Half Round to insert Balloon Catheter.
•
Spare Cold Knife Straight double stem.
Resectoscopes and associated accessories:
•
Resectoscope working element (For
single stem loops) with 2 cutting
loops, 2 coagulation electrodes, 2 cords (277), Protection tube 280
•
Electroscope Sheath including connecti
ng tube for in and outflow,
26 Fr, Rotatable inner tube with
ceramic insulation, for use with
working elements for continuous irrigation.
•
Schmiedtexamination insert tube and visual obturator.
•
Ellick evacuator.
•
Toomey syringe 100 cc.
Mauermayer stone punch:
•
Working element
•
Sheath Fr, with obturator / 1
14 / Electric regulator high voltage / Local made / good quality
220 volt 10000Amp / 4
15 / Stabilizer element / Local made / good quality
220 volt / 36
16 / Urothrotome / Best quality / 2
17 / Camera endoscopy / Imported/best quality / 2
18 / Rigid Bronchoscope + Oesgphascope / 4mm WL.215mm.
5mm WL 245mm
5.5mm WL.265mm
6.0mm WL265 mm
7.0mm WL 365mm
Having light source and venture for Anesthesia
Forceps:-- WL.350
i) Alligator FB forceps. (1)
ii) Universal forceps (1)
iii)Fenestrated forceps for soft FB (1)
iv)Peanut forceps (1)
v) Magnetic extractor (1)
WL.450
i) FB forceps alligator.
ii) Universal forceps
iii) Grasping forceps for soft FB
iv) Peanuitforcept
ACCESSORIES
1. Adaptor with sliding glass window plug, sealing cap,
notched lens and keyhole opening, movable.
2. Plug for ventilation Attachment of Bronchoscopes.
3. Adaptor from Bronchoscope to any type of pediatric
respiration equipment.
4. Atomizer with bulb working length 50cm (2)
5. Laryngeal Atomizer with bulb (2)
6. Suction Tube, Length 50 cm, diameter 2.2.5 & 3cm
19 / Tonsillectomy sets / 2 X Backhaus Towel Holding Forceps, 110mm
 1 X Bruenings Tongue Depressor, 190mm
 1 X Mc Ivor Frame Only
 1 X Tongue Spatula, Russel - Davis, 67x29mm
 1 X Tongue Spatula, Russel - Davis, 75x33mm
 1 X Tongue Spatula, Russel - Davis, 85x38mm
 1 X Good Tonsil Scissors, 195mm
 2 X Blohmke Tonsil Seizing Forceps, 205mm
 1 X Tonsil Elevator A. Dissector, Henke
 1 X Suction Cannula, Yankauer, Wide Cental Hole
 2 X Bruenings Tonsil Snare, 270mm
 1 X Wire Loop, Ph = 100 Each
 2 X Schnidt Tonsil Hemostat, 185mm
 1 X Nager Pillar Retractor, 230mm
 1 X Hartmann Tonsil Punch, 13mm D
 1 X Curette, Beckmann, Fig. 1
 1 X Curette, Beckmann, Fig. 2
 1 X Curette, Beckmann, Fig. 3
 1 X Curette, Beckmann, Fig. 4
 1 X La Force Adenotome, Small
1 X La Force Adenotome, Medium
 1 X Tissue Forceps, 2x3 Teeth, 200mm
 1 X Durogrip De Bakey Needle Holder, 180mm
 1 X Binding Device Form E / 1
20 / Tracheotomy sets / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 1
21 / Thyrodectomy sets / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 1
22 / Oxygen Cylinders with gauge trolley / It shall come with set of oxygen cylinder, cylinder
trolley and regulator/flow meters
 The oxygen cylinder and regulator/flow meters
shall be tested with Test Certificates from POL
(Pakistan Oxygen Ltd.), BOC (British Oxygen
Company) or other equivalent institution. Test
Certificates shall be provided for evaluation
 A Certificate of Conformance to the Test
Parameters and a Certificate of Origin indicating
the country of origin and date of manufacture
shall be available to the Buyer.
 150 and 48 cft size oxygen cylinder with medical angle
type pin index fitting, filled with Medical grade
oxygen
 Come with cylinder key/spanner/bar or hand wheel
to turn cylinder on/off,
 The cylinder shall be made of light weight
material such as aluminum or equivalent
 Bidder shall indicate the nominal oxygen filling
volume (in liter) of the above cylinders
Come with one trolley in suitable size to hold F
size medical oxygen cylinders
 To be fabricated from antirust treated epoxy
Powder coated mild steel tubular framework.
 With two large, minimum 100mm rubber wheels
with rims
 With chain retention mechanism to hold cylinder
on the trolley
 Able to be self standing and stable when parked
with or without cylinder
Flow:
It shall be Pin index type to fit the above oxygen
cylinders
 Regulated to convert standard cylinder pressure
(typically 2,000 psi) to approximately 4 BAR (4
atmospheres) pressure
 The regulator delivery pressure should be factory
pre-set, and does not permit user adjustment
 The adjustment of delivery pressure by
maintenance engineer via a screw slot or
covered or capped system is required
 The regulator MUST be diaphragm type; Needle
valve regulators are NOT permitted
 The regulator MUST provide genuine
PRESSURE reduction and not just flow reduction
 The flow meter to be attached to the regulator
output
 The flow meter should be spinning rota-meter
type and adjustable from minimum 0 to 5 litres of
oxygen per minute
 The regulator and flow meter MUST be an
integrated unit.
 The flow meter outlet should be ribbed nipple
type to permit connection of standard flexible
oxygen tubing
 The flow meter shall have outlet for connection to
nebuliser or humidifier bottle. However, the
nebuliser is not required to be included in the bid.
 All standard accessories/consumables/parts
required for the proper operation of the above item shall be included in the offer.
 All standard Maintenance tools and cleaning
/lubrication materials where applicable shall be
included.
 The unit offered shall be certified to meeting the
relevant quality and safety requirements of TUV,
CE mark (MDD), FDA, IEC, Radiation safety,
safety of pressurized equipment and any other
relevant quality and safety standards .
Certificates showing the compliance of this unit
offered with any relevant quality and safety
standards MUST be submitted
Local/Imported / 50 Nos 150 cft
50 Nos 48 cft
22 / Megal forceps (small size) / Local /best quality / 36
23 / Defibrillator / Semi automatic 340 joules biphasic defibrillator with
monitor and AED mode
 Biphasic Tran thoracic (external) defibrillator with
TFT/LCD colour display
 Synchronized output with ECG.
 Control of energy charging/ delivering on main panel &
apex paddle.
 Charging Indicators.
 The energy range should be adjustable for paeds and
adults up to 340 Joules.
 Charging Time for full energy will be less than 10 sec.
 Screen Size of approx. 5 inch coloured.
 Display of HR, ECG through paddles and Lead I.II & III
patient cable.
 Built in recorder for printing of full summery on
standard 50mm paper.
 Alarms for High and low Heart rate, low battery
warning.
 AC 220V / 50Hz operated.
 Built-in Rechargeable battery with charger for
minimum 50 shocks at max. energy.
 Auto tester/self check. External paediatric and adults Paddles, ECG cable.
 AED facility.
Pacing facility / 2
24 / Retractor Dewar / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
25 / Clamp large size / For all instrument made of non-magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 48
26 / Scissors Di / For all instrument made of non-magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 48
27 / T.A.H Screw / For all instrument made of non-magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 48
28 / Nebulizer / Cold and heated aerosol therapy
Water and medical aerosol therapy
Digital Control system for;
Air Flow
Therapy time
Nebulization output
Standard oxygen adaptor to addition of oxygen to delivered aerosol.
Variable therapy time
Long term water aerosol therapy with refill bottle
Transparent medication cups
On/Off heater
Mobile stand with lockable wheels
Autoclavable air hoses, ultrasonic cup and refill bottle to minimize contamination level
Local/Imported / 50
29 / Ophthalmoscope / Binocular indirect ophthalmoscope pupillary distance
adjustable, halogen illumination with output voltage
variable upto 6V, four spare bulbs, transformer, red free
filter, cobalt blue filter, teaching mirror, scleral depressor,
20D aspheric lens, detachment charts and carrying case / 4
30 / Right angle forceps / For all instrument made of non-magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
31 / Uterine holding forceps / For all instrument made of non-magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
32 / Artery forceps 6” curved / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
33 / Artery forceps 9” curved / For all instrument made of non-magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
34 / Alliciss forceps 6” / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
35 / Alleciss Forceps 8” / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
36 / Intestine clamps Non crushing / Material: Martensitic steel (quenched, magnetic steel)
Intestinal clamp, straight or curved
Jaws very springy and soft :
- Atraumatic
- Occlusion: the form and mechanical action must permit precise
closing
- Adhesion: provided by the surface of the jaws
Length: 17, 26cm
Packaging: Unit presentation: individual, with protective wrapping
The following should appear on the packaging:
- designation of the instrument
- name and address of supplier (manufacturer) / 24
37 / Intestine forceps (ovum) 8” / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
38 / Bib cock medium size / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
39 / Needle holder 8” / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
40 / Scissor curved 6” / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
41 / Scissor Curved 8” / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
42 / B.P Handle 21 Nos / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
43 / B.P Handle 15 Nos / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
44 / Devierrefrector different size / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
45 / Uritheraldialator / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 2
46 / Skin graft sit / Steel Knife Handles with the sterile 158mm Skin Graft Blades for harvesting "Macro" or "Major" Skin Grafts along with other required accessories. / 2
47 / Laheys artery forceps / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 24
48 / Desjardins forceps different size / For all instrument made of non magnetic stainless steel. All die made with hidden joints and leak proof. Manufactures mark most be indicated on all instruments / 48
49 / Oxygen regulator / CE marked
Bullnose fitting for large cylinders
Pin Index Version Available
Standard Flow Rate: 40 l/min
Maximum Flow Rate: 150 l/min
Single Stage Pressure Regulator
with Flowmeter 0
15 l/per min.
PreSet Pressure Relief Valve, calibrated at 10 bar
Vertical/Horizontal Positioning available
6cm long adaptor between flowmeter & regulator
Tubing Nipple
Every unit rigorously tested prior to despatch
Batch Number stamped on regulator for identification purposesComply fully with the requirements of HTM 2022 / 60
50 / Instrument trolley / SS Instrument trolley with three tiers.
 All welded construction with 3 fixed shelves.
 Swivel castors.
 Dimensions 700mm long x 400mm wide / 24
51 / Surgical drum / Steel Thickness, 0.80-1.00mm (22-20 gauge)