Quotation Request Form

Quotation Request Form

Please complete the form below for a no obligation test plan and quotation.

(If you require assistance please call us on 01371 856061)

YOUR CONTACT DETAILS:
Company Name: / / Contact Name: /
Address: / / Tel: /
/ Fax: /
/ Mobile: /
/ E-mail: /
Postcode: / / Website: /
Is your company: /
EQUIPMENT TO BE TESTED
Product Type /
Model / Name / Brand /
Intended use /
List of Variants to be covered by this certification
Rational for selecting EUT (i.e. worse case configuration) /

TESTING INFORMATION
Type of testing required /
Do you wish to attend the testing? /
In which environment will the product be used? /
Type of certification /
Standards Required
(Selection of standards and applicable classifications can be complex please tick appropriate box for ETS to advise)
For ETS to advise on applicable standards click here /
Please specify applicable standards *** /
Please specify applicable classification *** /
List of published standards click here
POWER REQUIREMENTS
Supply Voltage /
Power requirement /
Rated Power /
If DC supply, is product supplied with a plug top AC adapter /

Mechanical Information

LengthWidth

Height Weight

Handling Requirements

Description of Product:

Input / Output Cables
Number of external Cables /
Number of cables >3m in length /
External antenna connections /

Diagram of Proposed test Configuration

Please attach a sketch of the EUT and Support Equipment, showing interconnections to the email you send this form to.

List of Cables
No / Description / Type* / Maximum Length

* If screened cables are used then these must be declared in the documentation

Please note: For external power and signal cables that are hard wired to the equipment it may be necessary to reduce the length as required by the appropriate EMC test standard. Some example cable lengths required are listed:

• Flicker test power supply cable 1m.
• SURGE immunity test power supply cable 2m.
• FTB Immunity test power supply cable 0.55m.
• Conducted RF Immunity test power supply and signal cable 300mm.

If at the customer’s request cables for the EUT shall not be cut to the required length, this shall be recorded in the report as a deviation from the standard, noting the cable/port affected.

If due to special cable type physical constraints the required length cannot be complied with, this shall be recorded in the report as a deviation from the standard, noting the cable/port affected.

It will be required to list any deviations from the standards utilised in the Declaration of Conformity.

Product Design Information
Clock Oscillators >9KHz /
List of Clock Oscillators frequencies /
Does the product contain magnetically sensitive devices /
Radio Transceivers
Tx/Rx devices? /
Frequency of Ts/Rx device /
Does the radio carry its own approval /
Rated Operating Power /
Operating Frequency /
Operating Range /
Intended Use /

*Operating Modes of EUT:

(Please state the number and details of the operating modes necessary to fully exercise the EUT together with the cycle time required to exercise all functions.)

*Operating Mode: (Specify how the unit will be operated during testing).

*Do not know, please contact us to discuss.

Harmonic Current Emissions Test for Lighting Equipment (Lamps)

Lamps shall be aged for ≥ 100 hours before the test is carried out.

Has your equipment for test been pre-aged (Lamps)

In order to make reliable emission measurements representative of high LAN utilization it is only necessary to create a condition of LAN utilization in excess of 10% and sustain that level for a minimum of 250 ms. The content of the test traffic should consist of both periodic and pseudo-random messages in order to emulate realistic types of data transmission (e.g. random: files compressed or encrypted; periodic: uncompressed graphic files, memory dumps, screen updates, disk images). If the LAN maintains transmission during idle periods measurements shall also be made during idle periods.

Performance Criteria during Immunity testing:

(Describe how we can monitor the performance of the equipment, i.e. reading tolerances, mechanical operations, software, acoustical and visual)

Test Report and Documentation
Full test report /
Results Document /
Hard copies of results on the day /
Electronic copies of the results on the day /

Additional Information:

How did you find our website? /