PART No: 04997, 04998 & 04999

PRODUCT: Body Harness

MAKE & MODEL: TOYOTA 70 SERIES LANDCRUISER

(JANUARY 2000 – Onwards)

INSTALLATION INSTRUCTIONS

PLEASE ENSURE THAT INSTRUCTIONS ARE UNDERSTOOD PRIOR TO FITMENT

  1. In the engine bay, locate the vehicle battery (1).
  2. Route the power input harness (2) from the battery towards the RHS of the engine bay.
Note: Do not connect the power input harness to the battery at this point. /
For P/No: 04997 & 04999 only.
  1. Following the diagram on the right, house the two power & ground input harness female terminals (4) into the mating connector (3).
  2. Connect the power input harness connector (3) to the body harness mating connector.
  3. Seal the two connectors with electrical tape.
/
For P/No: 04998 only.
  1. Following the diagram on the right, house the three power & ground input harness female terminals (4) into the mating connector (5).
  2. Connect the power input harness connector (5) to the body harness mating connector.
  3. Seal the two connectors with electrical tape.
/
For P/No: 04998 & 04999 only
  1. Route the four electric brake controller wires (1)towards the RHS firewall grommet (2).
  2. Route the Body Harness tail / trailer connectors (3) down and towards the vehicle undercarriage.
/
For P/No: 04998 & 04999 only
  1. Locate the RHS firewall grommet (1).
  2. Cut the tip off one of the firewall grommet nipples (2).
  3. Route the Body Harness four electric brake controller wires (3) through the grommet hole and into the vehicle cabin.
  4. Seal the grommet using electrical .grease or silicone.
/
For P/No: 04998 & 04999 only
  1. Inside the vehicle cabin, route the Body Harness (1) behind the dash and into the driver’s side foot well area.
  2. Locate the four electric brake controller wires (2).
  3. Locate the electric brake controller (3).
  4. Mount the electric brake controller mounting bracket.
/
For P/No: 04998 & 04999 only.
  1. Following the diagram on the right, house the body harness terminals (1) to the corresponding slot on the connector (2).
  2. Insert the secondary lock (3) into the connector (2).
  3. Connect the body harness connector (2) to the electric brake controller.
/
For P/No: 04997 only.
  1. Route the Body Harness (1) down and towards the vehicle undercarriage.
/
  1. From the vehicle undercarriage, locate the body harness (1).
  2. Route the body harness along theRHS chassis rail and towards the rear of the vehicle.
Note: When routing any harnesses under the vehicle, ensure to avoid all moving parts, sources of heat and sharp objects. /
  1. Continue routing the body harness along the top of the RHS chassis rail and towards the rear of the vehicle.
/
  1. Following the path of the hydraulic lines, route the Body Harness (1) along the RHS chassis rail and towards the rear of the vehicle.
/
  1. Keeping clear of the rear suspension components, continue routing the Body Harness (1) along the RHS chassis rail and towards the rear of the vehicle.
/
  1. Route the body harness (1) along the rear of the vehicle and towards the trailer and tail harness connectors.
/
For P/No: 04998 and 04999 only.
  1. Locate the trailer and tail harness connectors.
  2. Disconnect the trailer harness 8-way female connector (1) and the tail harness 8-way male connector (2).
  3. Patch in the body harness mating 8-way connectors in between.
  4. Insulate all the connectors using electrical tape.
/
For P/No: 04997 and 04998 only.
  1. Connect the body harness 2-way female connector (1) into the 12-pin tail harness mating connector (2).
  2. Insulate all the connectors using electrical tape.
Note: Any future accessories can be patched in between these two connectors. Total power rating is 30-amps. /
For P/No: 04998.
  1. Connect the body harness (1) orange & orange/white wires (2) to the positive terminal on the vehicle battery (3).
  2. Connect the body harness (1) white wire (4) to the negative terminal on the vehicle battery (3).
  3. Secure the body harness with cable ties (not supplied).
/
For P/No: 04997& 04999 only.
  1. Connect the body harness (1) orange wire (2) to the positive terminal on the vehicle battery (3).
  2. Connect the body harness (1) white wire (4) to the negative terminal on the vehicle battery (3).
  3. Secure the body harness with cable ties (not supplied).
/
  1. Test the body harness using a light board or multimeter.
  2. Secure all harnesses using cable ties (not supplied).
  3. Re-fit all removed parts and secure all fasteners, ensuring there are no squeaks or rattles.
  4. Place the instructions in the glove box after fitment.