JJC MIC-1 Electret Condenser Microphone

MIC-1 Professional DV Stereo microphone fits for home-used DV. It is delicate and light, 2 built-in cartridges which are vertical to each other. The MIC-1 enables a natural sound pick-up. And it is with low voltage alarm indication, wide frequency, high sensitivity, and strong direction, long distance sound pick up, natural, clear and sweet.

Main Function:

The microphone can be fixed on the DV or DSLR with microphone hold and path.

The MIC-1 enables a natural sound pick-up.

Delivering a stereo sound image with superb clarity.

The pick up pattern (affecting the sound stage width) can be set to 90° or 120° according to the sound source.

Important Note:

The microphone is sensitive, don't drop it, or shake it. Keep it away from high temperature and humidity, especially more than 60°C.

It is put near the amplifier, the feedback will happen. If this happens, please put the microphone in the position far from the amplifier or turn down the volume of the amplifier.

If you change the setting of mode when you take the record, noise will occur.

If the windscreen catches the rain, it should be dried in the dry and cool place, not under the strong sunshine, to avoid aging.

Package includes:

MIC-1 Electret Condenser Microphone

Wind Screen

CR2 battery

Portable bag

Manual Instruction

Before using

Please install the battery in it when you are about to use the microphone.

Change battery

  1. Push the battery cover backward, then take it down.
  2. Push the battery forward, then take it down.
  3. Put the new battery into the slot.
  4. Put the cover back on the right position.

Time for changing battery

As the power is full, the indicating light will flash when you turn ON it.

When the indicating light is always shining in the process or using or after turning ON, That means the power of the battery is not enough, but it can still stand for one or two hour. Please change the battery in time.

The microphone can work for more than 800hours when you install the CR2 battery in the microphone. (The actual hour depends on the varied case.)

Affairs for safe

If you don't follow the rule of battery operation, it will lead to the leak of battery. Please abide the following rules:

  1. Don't charge the battery, the battery isn't chargeable.
  2. If you won't use the microphone in the long future, please uninstall the battery.
  3. If the battery leak the liquid, please clean the liquid in the battery tube before you install the new battery.

Connection

Put the hot shoe adapter to the hot shoe socket of the DV or DSLR (see Figure 1). And fix the microphone. Make sure the DV or DSLR is POWER OFF, then put the pin of "L" style mini stereo to the input terminal of the DV microphone. (See Figure 2)

Figure 1 / Figure 2
/
  1. Wind Screen:Cover on the microphone to reduce the wind sound and sound of breath.
  2. AF light:When you switch "OFF" to "ON", the light will flash then off for power saving. When the light is flashing for long time or it always flash in using. It indicates the power isn't enough, pleas replace the battery.
  3. Power/Mode of sound pick up: Locate the place according to the sound source.
  4. Battery cover
  5. Hot shoe connector
  6. "L" style mini stereo plug
  7. Cable clip: The cable could be fixed in it.

ON / Turn on
OFF / Turn off
90° / When pick up the sound in a limited area or from afar (For talking or playing musical instruments)
120° / When pick up the sound in a big area or a sound nearby. (For concert or drama)

Specification:

Frequency response: 30-1800Hz

Sensitivity: -40dB (0dB=1V/Pa at 1KHz)

Direction: Uni-direction

Output Impendency: 200Ω

S/N Ratio: 76dB (1KHz at 1 Pa)

Max SPL: 120dB (at 1 KHzs1%T.H.D.)

Power Requirement: DC 3V

Length of cable: 28cm

Dimension: 25mm*130mm*60mm

Weight::45g (not including battery)