PLASMA MOUNT
INSTALLATION AND OPERATION INSTRUCTIONS
Before beginning the installation of your new flat screen mount, first verify that you have all of the necessary tools at hand. The following tools are required for proper installation:
ü Phillips screwdriver
ü Stud finder for drywall installation
ü Electric drill and 5/16” (8mm) masonry bit for concrete/brick installation
Also make sure that all of the hardware has been included with your mount. You should find six bags containing the following:
Bag / Item / Ref / Bag / Item / Ref1 / (x4) M4x12 Bolt
(x4) M4x30 Bolt
(x4) M4 Lock Washer / A
B
C / 4 / (x4) M8x16 Bolt
(x4) M8x40 Bolt
(x4) M8 Lock Washer / J
K
L
2 / (x4) M5x12 Bolt
(x4) M5x30 Bolt
(x4) M5 Lock Washer / D
E
F / 5 / (x4) M4/M5 Spacer
(x4) M6/M8 Spacer
(x4) M4/M5 Washer / M
N
O
3 / (x4) M6x12 Bolt
(x4) M6x35 Bolt
(x4) M6 Lock Washer / G
H
I / 6 / (x6) Concrete Anchor
(x6) Drywall Screw
(x6) Washer / P
Q
R
Step 1 – Mount the Wall Plate
Drywall Installation
IMPORTANT: The weight of the television will require a minimum of two studs for safe installation.
Use a stud finder to locate two studs where you want to install your mount. It is recommended that you verify the location of each stud using a small nail or awl. Make sure you use the center of each stud.
After the studs have been located and verified, place the wall plate against the wall and secure it with a single Drywall Screw (Q) and Drywall Washer (R) in either side of the top portion of wall plate (see Diagram A). Do not completely tighten the screw yet. Next, using the bubble guide to ensure the wall plate is level, screw a second Drywall Screw and Drywall Washer into the opposite side of the top portion. Screw the remaining Drywall Screws and Drywall Washers into the wall plate (see Diagram B) and tighten all screws.
Diagram A
Concrete/Brick Installation
Begin by placing the wall plate into position against the wall, using the bubble guide to keep it level. Mark off six holes to be used for securing the mount and place the wall plate aside. Next, drill holes using an electric drill and 5/16” (8mm) masonry bit. Insert a Concrete Anchor (P) into each hole. If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall.
Once all of the anchors are in place, move the wall plate back into position. Screw a Drywall Screw (Q) and Drywall Washer (R) into each anchor (see Diagram B). Do not tighten until all screws are in place.
Diagram B
Step 2 – Attach Brackets to the Television
IMPORTANT: Make sure the television is unplugged before starting this step of the installation and never lay your television face down as this can damage the viewing surface.
You must first determine which hardware to use with your television. Begin by examining the back of the television to establish the length of bolt required: a television with a flat back usually requires a shorter bolt while those with a curved or recessed back take a longer bolt. Next, determine which diameter bolt to use. Four different diameter bolts have been included with your installation kit. Test each diameter bolt with your television until you find the one that fits. Take care not to force a bolt that is too large; if you feel any resistance, stop immediately to avoid damaging your television.
Next, attach the arm brackets to the back of the television using the correct size bolt and lock washer. If your television uses one of the smaller diameter bolts (M4/M5), use a Washer (O). Televisions with a curved or recessed back may also require a spacer (M or N; see Diagram C). Make sure all bolts are secure, but do not over-tighten.
M4/M5 Bolts M6/M8 Bolts
Diagram C – For televisions with curved or recessed backs
Step 3 – Final Installation and Operation
Final Installation
To complete the installation of your new plasma mount, carefully place the television brackets over the cross-bar located on the wall plate (see Diagram D). Heavier televisions may require two people to lift safely.
Diagram D
Operation and Adjustment
Your new plasma mount can be adjusted to fit your individual needs. You can adjust the tilt of your television by using the adjustment knob located on the right-hand side of the wall plate. First, unlock the adjustment bar by lightly pulling outward on the bottom of the television and pulling the adjustment knob outward. Next, turn the knob clockwise to raise the viewing angle or counter-clockwise to lower the viewing angle (see Diagram E). Once the desired level of tilt is achieved, release to lock the adjustment bar in place.
Other features of your display mount include a cord manager and lock designed to prevent your television from being removed from the cross-bar. The cord manager attaches to the cross-bar and can be used for neatly routing your television’s power cable. To use the security lock, locate the small metal tabs located on the arm brackets that attach to the television. Push these tabs inward so that lifting up on the television causes the tabs to come into contact with the cross-bar. Place a small padlock (not included) through the holes located on the tabs and arm brackets to prevent the tabs from being moved out of place (see Diagram F).
Diagram E Diagram F