Ch.10 Thermodynamics Notes
Heat, Work, and Internal Energy
•Heat and work are energy transferred to or from a system. An object never has “heat” or “work” in it; it has only internal energy.
•Q = c x m x DT -- where Q is heat, c is specific heat constant for each substance, m is mass, and DT is the change in temperature.
•A system is a set of particles or interacting components considered to be a distinct physical entity for the purpose of study.
•The environment the combination of conditions and influences outside a system that affect the behavior of the system.
•In thermodynamic systems, work is defined in terms of pressure and volume change.
•This definition assumes that P is constant.
•If the gas expands, as shown in the figure, DV is positive, and the work done by the gas on the piston is positive.
•If the gas is compressed, DV is negative, and the work done by the gas on the piston is negative. (In other words, the piston does work on the gas.)
•When the gas volume remains constant, there is no displacement and no work is done on or by the system.
•Although the pressure can change during a process, work is done only if the volume changes.
•A situation in which pressure increases and volume remains constant is comparable to one in which a force does not displace a mass even as the force is increased. Work is not done in either situation.
Thermodynamic Processes
•An isovolumetric process is a thermodynamic process that takes place at constant volume so that no work is done on or by the system.
•An isothermal process is a thermodynamic process that takes place at constant temperature.
•An adiabatic process is a thermodynamic process during which no energy is transferred to or from the system as heat.
Energy Conservation
•If friction is taken into account, mechanical energy is not conserved.
•Consider the example of a roller coaster:
–A steady decrease in the car’s total mechanical energy occurs because of work being done against the friction between the car’s axles and its bearings and between the car’s wheels and the coaster track.
–If the internal energy for the roller coaster (the system) and the energy dissipated to the surrounding air (the environment) are taken into account, then the total energy will be constant.
•The principle of energy conservation that takes into account a system’s internal energy as well as work and heat is called the first law of thermodynamics.
•The first law of thermodynamics can be expressed mathematically as follows:
DU = Q – W
Change in system’s internal energy (U) = energy transferred to or from system as heat (Q) – energy transferred to or from system as work (W)
Signs of Q and W for a system
Sample Problem
The First Law of Thermodynamics
A total of 135 J of work is done on a gaseous refrigerant as it undergoes compression. If the internal energy of the gas increases by 114 J during the process, what is the total amount of energy transferred as heat? Has energy been added to or removed from the refrigerant as heat?
Answer: Q = –21 J
Cyclic Processes
•A cyclic process is a thermodynamic process in which a system returns to the same conditions under which it started.
•Examples include heat engines and refrigerators.
•In a cyclic process, the final and initial values of internal energy are the same, and the change in internal energy is zero.
•Unet = 0 and Qnet = Wnet
•A heat engine uses heat to do mechanical work.
•A heat engine is able to do work (b) by transferring energy from a high-temperature substance (the boiler) at Th(a) to a substance at a lower temperature (the air around the engine) at Tc(c).
•The internal-combustion engine found in most vehicles is an example of a heat engine.
The Steps of a Gasoline Engine Cycle
The Steps of a Refrigeration Cycle
Thermodynamics of a Refrigerator
Efficiency of Heat Engines
•The second law of thermodynamics can be stated as follows:
No cyclic process that converts heat entirely into work is possible.
•As seen in the last section, Wnet = Qnet = Qh – Qc.
–According to the second law of thermodynamics, W can never be equal to Qh in a cyclic process.
–In other words, some energy must always be transferred as heat to the system’s surroundings (Qc > 0).
•A measure of how well an engine operates is given by the engine’s efficiency (eff ).
•In general, efficiency is a measure of the useful energy taken out of a process relative to the total energy that is put into the process.
•Eff = Worknet / Qh
•Note that efficiency is a unitless quantity.
•Because of the second law of thermodynamics, the efficiency of a real engine is always less than 1.
Sample Problem
Heat-Engine Efficiency
Find the efficiency of a gasoline engine that, during one cycle, receives 204 J of energy from combustion and loses 153 J as heat to the exhaust.
Answer: eff = 0.250
Entropy
•In thermodynamics, a system left to itself tends to go from a state with a very ordered set of energies to one in which there is less order.
•The measure of a system’s disorder or randomness is called the entropy of the system. The greater the entropy of a system is, the greater the system’s disorder.
•The greater probability of a disordered arrangement indicates that an ordered system is likely to become disordered. Put another way, the entropy of a system tends to increase.
•Greater disorder means there is less energy to do work.
•If all gas particles moved toward the piston, all of the internal energy could be used to do work. This extremely well ordered system is highly improbable.
•Because of the connection between a system’s entropy, its ability to do work, and the direction of energy transfer, the second law of thermodynamics can also be expressed in terms of entropy change:
The entropy of the universe increases in all natural processes.
•Entropy can decrease for parts of systems, provided this decrease is offset by a greater increase in entropy elsewhere in the universe.
Energy Changes Produced by a Refrigerator Freezing Water
Because of the refrigerator’s less-than-perfect efficiency, the entropy of the outside air molecules increases more than the entropy of the freezing water decreases.