Sam S.
SKILLS:
HVAC / Mechanic
Over 8 years’ experience installing duct work, all conventional heating and cooling equipment, and accessories.
Experience in seasonal cleanings, troubleshooting electrical components. (High / low- voltage).
Over 5 years designing custom duct systems for residential homes
Read prints, design, lay out, installing duct work, piping, and electrical for residential, commercial, or industrial applications. Stick weld, solder, braze, or thread all piping, stainless, carbon, pvc Sch 40 80, cpvc, copper, trac pie, and Spencer tubing. The ability to improvise and make fittings on-site. Transitions, end caps, plenum, filter racks, or offsets. Over 5 years’ experience in industrial maintenance/millwright. The tear down and repair of industrial machinery to spec. Installing new equipment according to prints and spec working closely with facility engineers, field verifying, designing, and installing all mechanicals for industrial heat ex-changers, extruders, vessels, pumps, and vacuums.
I am OSHA safety certified and dedicated to job safety. Also I am a people person and I enjoy working and building relationship with clients.
Work Experience
Mechanic/ Millwright
Blue Hen Industrial May 2013-January 2014
Layout and assemble new equipment
Troubleshoot, diagnose, repair, electrical, and mechanical equipment.
Fabricate replacement parts from metal.
Measure, cut, bevel, and fit pieces to be welded
Rig heavy equipment with, chokers slings, chain-falls, and cranes.
Work from man-basket on crane. Send and receive signals from operating engineer.
Operate heavy equipment, boom lifts, forklifts, lull, skid steer, excavator, and front-end loader.
Mechanic/Millwright/fitter
Collett and Son Welding / Mill righting August 2011-May 2013
Disassemble machinery or equipment to remove parts and make repairs.
Repair, install, and maintain the operating condition of industrial production or processing machinery and equipment
Study blueprints or manufacturers manuals; confer with plant engineers or maintenance to determine correct installation and operation of machinery.
Work in machine shop fabricating replacement parts, brackets, braces, and pipelines from blueprints.
Rig heavy, very expensive, and fragile equipment. Work hand in hand with crane operator coordinate set up, rigging, and signal calling of all picks
Skillful deconstruction of, vessels, tanks, tractor trailers, and machinery with oxy acetylene torch Hold safety classes once a month to go over Industrial safety procedures/ protocol and lock out tag out procedures.
HVAC Mechanic
Chelsea Heating and Air February 2008-December 2011
Install residential or commercial duct work(split system or zone) and all heating and cooling equipment. (Dampers, Zone Panels, Humidifiers.).
Install geothermal heat pumps, hot water heaters, and hot water generators.
Install all gas pipe, vents, fusion pipe, electric(high/low voltage), and drains to code. Solder, Braze or Thread pipe.
Remove old units and recover Freon and log.
Design duct systems on special projects. (Old homes)
Rough in residential new construction homes
Perform seasonal cleanings, troubleshoot, and service all heating and cooling equipment
Helper HVAC
McDaniel Plumbing Pipefitting June 2003-April 2006
Cut or drill holes in floors, walls, or roof to install equipment, and register.
Measure, cut, thread, or bend pipe or tubing. Solder and braze cooper.
Run heat runs, tape duct, and insulated duct.
Wire thermostat, switches, and outlets.
Level dirt for A/C pad and make sure A/C is level
Education
High School Diploma or Equivalent, VAC
Hodgson Votech Newark, DE
Licenses & Certifications
EPA Certification 608609 - October 26th, 2011
Type 1 Certification - Small Appliances Type2 Certification - High-Pressure Type 3 Certification Low
Pressure Certification No: 000367865
OSHA Construction Safety
Educated on all OSHA's safety requirements