Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

TITLE OF THE PAPER

(16 PT, BOLD, CAPITAL LETTERS)

Name1. Surname11[*] – Name2. Surname22 – Name3. Surname33 (11pt, bold)

1Department Name, Faculty Name, University Name, Address (10 pt)

2Department Name, Faculty Name, University Name, Address

3Department Name, Faculty Name, University Name, Address

ARTICLE INFO (11 pt, bold)…filled by the publisher / Abstract:(11 pt, bold italic)
Article history: (11pt, bold italic)
Received
Received in revised form
Accepted / The abstract shouldnot contain more than 250 words including objective, methods, procedures, experimental investigations as well as main outcomes and results. Do not cite references and do not use abbreviations in the abstract.
Keywords:
(11 pt italic, maximum of 6 keywords)
Keyword1
Keyword2

Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

1Introduction (12 pt, bold)

1.1Manuscript preparation (11 pt bold)

(11 pt) Journalarticlesubmissionimpliesthat thearticle is notsimultaneouslyconsidered forpublicationelsewhere, has to be original and previously unpublished. Author is responsible for the data presented in his article.Manuscript should be written in good English. Submission should be made using the online manuscript submission system. Please register yourself at the journalweb site.You can upload your manuscript after logging in as an author.

The manuscript is to be prepared on A4 paper formatted in Microsoft Word, written inthe third person, in a metrological correct way, using SI units and allowed terminology.

The manuscript has to be written using Times New Roman font and with single line spacing.

  • The manuscript has to be prepared in the form of double columns text, written in two 8.2 centimeters-wide columns. Column distance is 6 mm.
  • The whole manuscript (including figures, tables etc.) should have at least 6 pages.

Corresponding author’s personal information should be placed in the footnote at the first page of the manuscript by double-clicking on the asterisk or as editing the simple text.

2Experimental investigation

2.1Basic Information

1)The margins of manuscript are:

  • top: 40 mm
  • bottom:20 mm
  • left:20 mm
  • right:20 mm
  • header:22,7 mm

2.2Additional Information

The chapter and subchapter titles are signed consecutively with numbers. The equation has to be written in the middle of the text column and it must be numbered in brackets on the right side. Equations have to be written according to the following rules:

(1)

Figure 1.Strength dependence on temperature for material xxx.

1)Size:

  • Full:11 pt
  • Subscript / Superscript:8 pt
  • Sub–Subscript / Superscript:6 pt
  • Symbol:14 pt
  • Sub–symbol:11 pt

2)Style:

  • Text:Times New Roman
  • Function:Times New Roman
  • Variable:Times New Roman, italic
  • Greek:Symbol
  • Matrix - Vector:Times New Roman, bold
  • Number:Times New Roman

Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

Figure 2.Strength dependence on temperature for material xxx.

Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

Each figure (drawing, diagram and photograph) must have a title at the bottom, e.g. in Fig. 1 (Times New Romanitalic font 11 pt).

The following formats are recommended: TIFF, JPG, GIF. All images must be acquired with a minimum resolution of 600 dpi. All descriptions placed on the figuremust be readable and clear.Table must have a title at the top, e.g. in Table 1 (Times New Romanitalic font 11 pt). Smaller figures and tables should be in the column. Large figures and tables can be placed over the entire page width, but in that case it is recommended to place them at the top or bottom of the page.

In the case when the list of notifications is given it should be placed before introduction, but not numbered.Acknowledgement, on the other hand, should be placed prior to the references.

Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

Table 1.Achieved result for STT and GMAW processes

Arc time / Heat input / Electrical energy consumption
min / J/mm / kWh
STT 1 / 3.42 / 725.2 / 0.74
STT 2 / 3.54 / 712.6 / 0.72
STT 3 / 3.86 / 695.5 / 0.69
STT 4 / 4.32 / 650.7 / 0.66
STT 5 / 4.50 / 638.4 / 0.61
STT 6 / 4.89 / 605.3 / 0.54
STT 7 / 5.17 / 580.6 / 0.43
STT 8 / 5.48 / 551.2 / 0.37
STT 9 / 5.91 / 537.4 / 0.29
STT 10 / 6.05 / 513.9 / 0.21
MAG / GMAW / 7.33 / 825.6 / 0.337

Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

3Results and discussion

The Editor /Editorial Board may reserve the right to decide whether a paper is acceptable for publication, and if necessary may require changes to the content, length or language.

4Conclusion

Conclusion should summarize main results of the paper. References to other papers, books, etc., must to bearrangedaccording totheirappearancefrom the beginningof the text using square brackets, and must be listed at the end of the paper. Samples are given below.

References

[1](Book) Surname1, N1., Surname2, N2.: Book title, Publisher, City, year.

2(Journal article) Surname1, N1., Surname2, N2.:Article title, Journal name, volume number (year), issue number, page numbers.

3(Conference article) Surname1, N1., Surname2, N2.:Article title, Conference name, Conference location, year, page numbers.

4Genta, G.: Vibration of structures and machines, Practical aspects, Springer-Verlag, New York, 1999.

[5]DeRuntz, D. B.:Assessing the Benefits of Surface Tension Transfer Welding to Industry, Journal of Industrial Technology, 19 (2003), 4, 55-62.

[6]Tyson, J., Schmidt, T., Galanulis, K.: Advanced photogrammetric for robust deformation and strain measurement, Proceedings of the 2002 SEM Annual Conference, Milwaukee, Wisconsin USA, 2002, 1-6.

Engineering Review, Vol. XX, Issue X,XX-XX, 201X.1

______

[*] Corresponding author. Tel.: …… ; fax: ……

E-mail address: .