BESAM PASSPORT 900 SERIES SPECIFICATION
OVERHEAD CONCEALED SWING DOOR OPERATOR
MATLESS SWING DOOR CONTROL
HEAVY DUTY SWINGING DOOR PACKAGE
Besam Entrance Solutions February 2008
1900 Airport Road
Monroe, NC 28110
Toll Free (866) 237-2687
Phone (704) 290-5520
Fax (704) 290-5544
Web Site www.besam.com
Product Guide Specification
Specifier Notes: This product guide specification is written according to the Construction Specifications Institute (CSI) 3-Part Format, including MasterFormat, SectionFormat, and PageFormat, contained in the CSI Manual of Practice.The section must be carefully reviewed and edited by the Architect to meet the requirements of the project and local building code. Coordinate this section with other specification sections and the drawings.
Delete all "Specifier Notes" when editing this section. /
SECTION 08460
AUTOMATIC DOOR OPERATORS
Specifier Notes: This section covers Besam “PassPort” package with Swingmaster 900 overhead concealed operator unit (surface mounted operator is also acceptable), PassPort swing door presence sensor, motion detector, CUHub plug-n-play interface module, PassPort beam kit and center pivoted aluminum swing door. If necessary, consult Besam for assistance in editing this section for the specific application. /PART 1 GENERAL
1.1 SECTION INCLUDES
PassPort automatic swinging door package consisting of Swingmaster 900 overhead concealed operator unit (surface mounted operator is also acceptable), PassPort swing door presence sensor, motion detector, CUHub plug-n-play interface module, PassPort beam kit and center pivoted aluminum swing door. Perform installation by the local Besam provider. Besam Program Module to be used by installer during installation. For the name and number of your local Besam provider, please call toll-free (866) 237-2687.
1.2 RELATED SECTIONS
Specifier Notes: Edit the following list of related sections as required for the project. List other sections with work directly related to this section. /A. Section 08410 - Aluminum entrances & storefronts
B. Section 08120 - Aluminum doors & frames
C. Section 08710 - Door hardware
D. Section 08810 - Glass and glazing
E. Section 07920 - Caulking & sealants
F. Division 1600 - Electrical
1.3 REFERENCES – (Codes & Approvals)
Specifier Notes: List standards referenced in this section, complete with designations and titles. This article does not require compliance with standards, but is merely a listing of those used. /A. Unit described complies with current ANSI A156.10 for Power Operated Pedestrian Doors.
B. Unit described complies with current ANSI A156.19 for Power Assist and Low Energy Power Operated Doors and with ANSI A117.1.
C. Unit is listed with UL 325-1997 standard for Door, Drapery, Gate, Louver, and Window Operators and Systems and UL991.
D. Unit is listed with UL991 Tests for Safety-Related Controls Employing Solid-State Devices
E. CUL approved (for use in Canada).
F. Unit complies with NFPA 101 Life Safety Code
G. Unit complies with NFPA 70 National Electrical Code
H. Unit complies with UBC (1997) Uniform Building Code
1.4 PERFORMANCE REQUIREMENTS
A. Automatic door equipment accommodates medium to heavy pedestrian traffic and up to 300 pound (136kg) weight of doors.
B. Motion and presence sensor capable of operating within temperature ranges of operating temperature range of - 30°F (-34°C) to 131°F (55°C).
1.5 SUBMITTALS
PassPort 900 Series 08460 - 6
A. Product Data: Submit manufacturer's product data and standard details for automatic operators.
B. Shop Drawings: Submit shop drawings for the fabrication and installation of automatic operators and associated components of the work. Include anchors, hardware and other components not included in manufacturer's standard data.
1.6 OPERATION AND MAINTENANCE DATA
A. Spare parts list and owners manual are available from the manufacturer
1.7 QUALITY ASSURANCE
A. Local Besam provider to install operator in accordance with current ANSI/BHMA A156.10 American National Standard for Power Operated Pedestrian Doors and local applicable codes. For low energy applications, local Besam provider to install operator in accordance with ANSI A156.19, ANSI 117.1, NFPA 101 and local applicable codes. The system fulfills Americans with Disabilities Act (ADA) requirements for barrier free entrances. All door openings must be at least 3232" (813mm813mm) wide to comply. Note: local codes may require greater door opening than ADA requirements.
1.8 QUALIFICATIONS
PassPort 900 Series 08460 - 6
A. Company specializing in manufacturing the products specified in this section shall have minimum ten years experience and be a member of the American Association of Automatic Door Manufacturers (AAADM). Prior to placing door(s) in operation, an AAADM technician should inspect the doors to check for compliance with current ANSI/BHMA A156.10 American National Standard for Power Operated Pedestrian Doors.
B. Manufacturer to provide FACTORY owned central dispatch system for warranty service throughout North America. System to be available 24 hours a day, 365 days per year with a factory employee (not an answering service) to obtain malfunction information and dispatch appropriate service agency to the customer location. Toll free (877) 237-2687 to be prominently displayed on header of each operator. To insure quality service dispatching, outside contractors or answering services will not be accepted.
1.9 WARRANTY
A. Besam's automatic door components are warranted to be free of defects in materials or workmanship under normal use for a period of one year from the date of shipment from Besam's factory when an authorized Besam provider has installed the components. Abuse, misuse, modification or improper repair or service by unauthorized technicians negates this warranty. During the period of this warranty Besam, at its sole option, will repair or replace any Besam automatic door component or parts thereof found to be defective in material or workmanship if any necessary return charges are prepaid. Components repaired or replaced under this warranty are warranted only for the remainder of the period covered by this warranty. For expanded warranty terms see Besam’s warranty certificate.
PART 2 PRODUCTS
2.1 MANUFACTURER
A. Provide PassPort 900 series automatic swing door package as manufactured by Besam US Inc., 1900 Airport Road, Monroe, North Carolina 28110. Toll Free (866) 237-2687. Phone (704) 290-5520. Fax (704) 290-5544. Web Site www.besam.com. E-Mail . Installation to be performed by the local Besam provider.
2.2 EQUIPMENT
B. PassPort 900 package consists of Swingmaster 900 series overhead concealed operator unit (surface mounted operator is also acceptable), PassPort swing door presence sensor, motion detector, CUHub plug-n-play interface module, PassPort beam kit, and center pivoted aluminum swing door.
2.3 AUTOMATIC SWING DOOR OPERATOR
A. Operator: Electro-mechanical operator, powered by 24 volt, 1/4 hp motor with field serviceable motor brushes. Completely assembled and sealed unit which includes helical gear drive transmission and interconnected rack and gear system for compression of exterior replaceable heavy duty spiral spring, all contained within a die cast aluminum housing and filled with special lubricant for extreme temperature conditions. Drive shaft is minimum 15/16" (24mm) thick containing 14 tooth splines to maximize bearing surface contact with drive arm assembly to eliminate slippage. Interfaced with the transmission system is a DC shunt-wound permanent magnet motor with sealed ball bearings. System operates from 120 VAC-60 cycle-1 phase power supply. Operator is mounted in the header case housing using vibration isolators to maintain quiet operation. Operator is to be non-handed for left and right handed doors and be able to push or pull the door open to 90°. Integrated microprocessor controlled utilizing the CUHub to coordinate all ANSI A156.10 required safety sensor systems.
B. Operator Housing: Non-handed operator is completely contained in a 6" (152mm) wide x 6" (152mm) high extruded aluminum housing. All aluminum sections are 6063-T5 alloy and have a minimum thickness of .156" (4mm). The operator housing provides a seal against dust, dirt and moisture.
PassPort 900 Series 08460 - 6
C. Electonic Controls: A self-contained, solid-state integrated circuit controls the operations and switching of the swing power operator. The electronic control provides low voltage power supply for all means of actuation. No external or auxiliary low voltage power source will be allowed. The control includes adjustable time delay (1 to 60 seconds) for normal cycle. Control unit must also include wake up protection for power outages and panic breakaway. The Swingmaster 900 CU2 control also has the following built in features:
1. Torque limiting for controlled forces on opening.
2. Acceleration control for smooth starts and recycle.
3. Special circuitry for reducing power to the motor when door is in HOLD-OPEN mode, extending longevity and assuring reliability.
4. Ramp down control for backcheck
5. Plug-N-Play ready to reduce mis-wiring and labor
6. Ribbon Harness for plug-n-play interface with CUHub and sensors. No screw lug terminals or wire nut connections will be accepted.
E. Connecting Hardware: Surface mounted operator is connected to the door by means of a cast steel door arm. The door arm is secured to the top rail of the swing door using one piece threaded tubular inserts for aluminum doors, 1/4-20 binding head and post screws (sex bolts) for wood and hollow metal doors. The toothed door arm adaptor is broached for positive engagement with the shaft and requires no additional linkage, slide blocks or tracks. The appearance of the top rail of the swing door shall be modified in order to attach the door arm.
F. Power Open: Automatic door operator powers the door open by forces transmitted mechanically to the drive shaft and maintains a constant engagement throughout the opening cycle. Operator is designed to counteract most normal exterior wind conditions and/or interior stack pressure without the need of additional power assist mechanisms. The automatic door system functions as a manual door closer in the event of a power failure. The automatic door system is electro-mechanical in design requiring no remote pumps or compressors.
G. Spring Close: Automatic door operator is spring closed. Spring is designed to withstand most normal wind conditions and return the door to the full closed position. Closing forces regulated by utilizing the motor and gear assembly as a dynamic brake. The spring is compression type to ensure longevity.
H. Emergency Breakaway: All inswing doors, which are required exits, are equipped with an emergency breakaway switch which internally cuts power to the operator. No external power switch will be allowed. The breakaway feature allows center-pivoted doors to swing in the direction of egress with forces that comply with current ANSI/BHMA A156.10 American National Standard for Power Operated Pedestrian Doors. Following emergency breakaway the doors return to the full closed position and electrically reset automatically. System must include a wake up circuit of no less than 3 seconds to allow the safety system to survey the surroundings to prevent ghost openings or recycling.
SWING DOOR:
Narrow (or medium) stile swing door as manufactured by Besam Entrance Solutions and is complete in all respects consisting of the following:
1. Narrow (or medium) stile heavy-duty aluminum door fabricated of 6063-T5 alloy.
2. Besam end load, bottom pivot.
3. Top arm prep for Swingmaster 900 swing door operator.
4. Quick disconnect wiring harness.
5. Mechanical 1 point lock (2 point lock for pairs of doors).
6. Jamb tubes (optional) and finger guards as required by UL.
2.4 SENSOR SYSTEMS FOR APPROACH AND SAFETY
MOTION SENSOR CONTROL DEVICE – select one of the following:
A. Actuation and safety devices are as indicated on door schedule and specified herein. Controls cause door to open instantly when device(s) located on approach side of door is actuated; hold door in open position, and cause door to close - unless safety device or re-actuation of opening impulse overrides such operation.
1. Motion sensor. (See expanded specification under Section I -- Actuators and Controls)
2. Overhead presence sensor. (See expanded specification under Section I – Actuators
and Controls)
3. Directional motion detector (approach and/or swing side). (See expanded specification under Section I -- Actuators and Controls)
4. Matless presence sensor. (See expanded specification under Section I -- Actuators and Controls)
5. Floor control mats -- size in accordance with current ANSI/BHMA A156.10 American National Standard for Power Operated Pedestrian Doors.
B. Motion detection device specified herein is based on K-band frequency technology, eliminating ghosting effect and band width jamming prevalent with X-bands, and providing motion detection twice as fast as X-band technology, with a higher quality detection pattern. Circuitry design eliminates Radio Frequency Interference (RFI) and Electromagnetic Interference (EMI). Detection patterns remain very stable in extreme weather conditions.
1. The motion detector is a unidirectional/bidirectional sensor which operates only on the FCC approved K-band frequency (24.125 GHz) It shall utilize a planar, (flat antenna) and for aesthetic purposes the unit shall be no larger than 4- 3/4" W x 3 1/8" H. x 2" D.
2. Relay hold time from 0.5 seconds to 9.0 seconds. Adjustable for unidirectional or bi directional sensing capabilities, wide or narrow patterns. All adjustments must be made by a universal coded infrared remote control. Mounting height, 7' to 11' above finished floor.
C. Select Finish
1. Finish: (Black, ready for non-metallic field finish painting).
2.5 SWING DOOR SAFETY DEVICES – PASSPORT
General: Safety devices specified herein operate on active infrared technology.
A. The “PassPort”: active infrared presence device shall utilize a combination of focused and diffused technology. The “PassPort” is powered by 24VAC/DC electronics supplied by the controller and shall recognize 2 different patterns: 1) when door is closed and 2) when door is open. When door is in open position it will provide 1’ of threshold protection with an adjustable self-adaptation time of 30 seconds to 25 minutes. The PassPort protection pattern will go through the threshold and overlap the motion pattern. All adjustments must be made by a universal coded infrared remote control. Mounting height 7’ to 9’ above finished floor.
B. “Safety Beams” (PassPort Beam Kit) Active infrared safety beams, located 5 inches past the lead edge of the door in the full open position, will provide additional safety in the closing cycle. In the event someone breaks the beams, the door will not recycle open. Beams are connected to CUHub plug-n-play interface module. Note: guide rails are provided and installed by installing provider.
C. Two sensors required for single doors. Four sensors required for pair of doors.
Door mounted detectors shall use active infrared technology with distance measurement. 12V – 24V AC or DC power requirements.