ISHPC2017-XXX

Extended Abstract for the International Sorption Heat Pump Conference 2017

First AUTHOR1*, Second AUTHOR2

1Organization, Department or Equivalent,, City, State, Country

2Organization, Department or Equivalent, City, State, Country

* Corresponding Author

Contact Information (Phone, Fax, E-mail)

ABSTRACT

This guide is prepared for authors of 2 page extended abstract for International Sorption Heat Pump Conference 2017 to be held in Tokyo, Japan on August 7-10, 2017. The extended abstract has to be submitted in Word file or in PDF file through the Online Submission System (http://biz.knt.co.jp/tour/2017/ISHPC2017) before February 28th, 2017. In addition, the final revised extended abstract should be submitted before June 16th, 2017. Each accepted extended abstract must have at least one paid regular or student early-bird registration before June 16th, 2017 to ensure that their presentation is included in the Conference Program.

1. INTRODUCTION

Authors are responsible for typing with accuracy and proofreading the extended abstract. It must look professional and be technically correct in order to be accepted.

2. LAYOUT AND FORMAT

2.1 Paper Size and Margins

The extended abstract has to be in A4 paper size (210 x 297 mm) with 2 pages. Top, bottom, left, and right margins are 25.4 mm each.

2.2 Manuscript Title

Center the manuscript title with font size of 14-point bolded with a blank line below the title.

2.3 Authors

All authors should be listed by their full name with the family name appearing last (e.g., Taro YAMADA, John SMITH). The affiliation of all co-authors should be listed as in the template. The corresponding author should be indicated by asterisk and the contact information has to be provided.

2.4 Text

Times or Times New Roman font type MUST be used for any text in the document including captions and header information. All text in paragraphs has to be in 10-point type. All paragraphs must be single-spaced with a double space between each paragraph. The paragraph format is “justified”.

3. HEADINGS

The titles of the main sections have to be centered, numbered and in 12-point bold type capital letters. With the exception of the abstract, nomenclature, references, and acknowledgements, section headings have to be numbered. Blank lines need to be placed above and below each main section title.

3.1 Sub-Section Headings

Sub-sections headings have to be in lower case, 11-point bold type letters. A blank line has to be placed above, but not below them.

3.1.1 Sub-sub-section headings: Sub-sub-sections should be avoided. If they are used, they should be justified left, in normal small letters, with the text beginning to the right.

4. FIGURES AND TABLES

Each table must be numbered (Table 1, 2, 3, etc.), with the caption centered above the table and table number in bold as shown in Table 1. Each figure must be numbered (Figure 1, 2, 3, etc.), with the caption centered below the figure and figure number in bold as shown in Figure 1. Figures and tables should be incorporated into the main body of the text.

5. EQUATIONS

Equations are to be centered, numbered in order (i.e., (1), (2), etc.) down the right-hand side of the page and cited in the text with its number, e.g., “… as listed in equation (1)”. Use 1.5 spacing, if necessary, for equations. For example,

(1)

Symbols used in equations should be explained directly below the equation in which they first appear or in a nomenclature section at the end of the manuscript. SI units only or dual units have to be used. If dual units are used, the equivalent values in the secondary units, enclosed in parentheses, will immediately follow the original values in the primary units, i.e., SI (IP) or IP (SI).

Table 1: Paper size and margins

Paper size / Top / Bottom / Left / Right
A4 / 25.4 mm / 25.4 mm / 25.4 mm / 25.4 mm

6. CONCLUSIONS

Conclusions can be in paragraph form or bullet items. Remember the following:

·  If you do not submit your paper according to the guidelines specified in these instructions, there is NO GUARANTEE that your paper will be included in the conference proceedings.

·  About 20 high-class papers selected from the extended abstracts will be recommended to a special issue of the International Journal of Refrigeration.

ACKNOWLEDGEMENT

An acknowledgement can be located immediately after CONCLUSIONS.

NOMENCLATURE

A short nomenclature can be located at the end of the text, if necessary.

Be dimensionless variable ( - ) Ĉ second variable (s2)

QA third variable (kJ) wx fourth variable (m2/s)

REFERENCES

Number references consecutively in the text, and enclose the citation number in square brackets (for example, [1]). The sentence punctuation follows the bracket [2].

For example:

[1] Author, A., Author, B., 2017, Title of the research paper, Journal title 8, 7-10.

[2] ISHPC2017, http://biz.knt.co.jp/tour/2017/ISHPC2017/index.html, Last accessed 16/June/2017.

International Sorption Heat Pump Conference 2017, Aug. 7-10, 2017, Tokyo