WP3215 COMSILENT N2

BOOSTER DATA SHEET

WP3215CS Data Sheet Nitrogen Booster Data Sheet
Final Operating Pressure / Speed / UNITS
1770 RPM
(60 Hz)
Flow & Power / 1450 PSIG Outlet Pressure
(0 – 4.5 PSIG Regulated Inlet Pressure) / 10.4-13.5 / SCFM
11 / HP
2900 PSIG Outlet Pressure
(0 – 4.5 PSIG Regulated Inlet Pressure) / 10.0-13.0 / SCFM
11.2 / HP
4000 PSIG Outlet Pressure
(0 – 4.5 PSIG Regulated Inlet Pressure) / 9.3-12.1 / SCFM
11.4 / HP
Technical Specifications / Motor rating / 12 (8.7 KW) / HP
Current @ 460 Volts / 14.4 / Amps
Weight / 1135 / Pounds
Noise level @ 3 ft / 72 / dB(A)
Heat dissipation / 34,000 / Btu/hr
Cooling air needed / 1,000 / CFM
Residual oil content at gas outlet (without filtration) / < 3 / mg/m3
Delta temperature (gas oultet vs. ambient) / 18 / °F
Operational ambient temperature range / 40-110 / °F
Operating pressure range / 1450-4000 / psig
Oil sump capacity / 6.1 / Quarts
Dimensions (L x W x H) / 60 X 31 X 62 / Inches
Cooling method / Air-Cooled
Drive type / Direct Drive
Stages/Cylinders / 3/3

*All data is with 5 % tolerance and is related to ambient conditions of 68 ° F and 14.7 PSIA.

Package Includes:

  • Feed tank run-permissive sensor (supplied loose)
  • Inlet Buffer Tank and Regulator Assembly
  • Intercoolers and aftercooler
  • Oil and water separators after the 1st,2nd and 3rd stages
  • Safety valve after each stage
  • 1st,2nd, and 3rd stage pressure gauges
  • Solenoid valves (115 V / 60 Hz) for automatic drainage of the separators
  • Unloaded starting relief and automatic condensate drain system
  • Condensate demister to easily dispose of condensate drainage
  • Assembly of compressor and electric motor
  • Resilient mounts including drainage hoses and air/gas outlet hose
  • 460/3/60 electric motor with IP 55 (TEFC) protection
  • Non-return valve mounted to air/gas outlet hose
  • Low oil pressure shutdown switch
  • High air/gas temperature shutdown switch mounted at the air/gas outlet of the compressor
  • Final gas filtration for oil free gas delivery
  • Compressor control system (including motor starter) for starting/stopping the compressor, and monitoring the oil level, air/gas outlet temperature and outlet pressure of the compressor
  • Complete package wired and mounted on a skid, and enclosed in a sound dampening canopy
  • Air/gas pressure sensor for automatic start/stop

Standard warranty is 15 months from date of shipment or 12 months after initial installation and start-up, whichever comes first. Ask your Sauer USA representative if your project requires an extended or alternative warranty period.

Sauer Electronic Compressor Control (ECC technology):

Electronic Compressor Control (ECC) advanced embedded control solution:

MountingIntegral

Power:6.1HP

Power Supply:60Hz / 3Ph

Control voltage:115V ac

Disconnect mains supply:Red handle, yellow locking collar

Emergency Stop:Latched pushbutton

Protection:IP 54

Power supply to processor:24 V ac

Operation:

  • AUTO automatic - Start / Stop ( based on suction (feed) and final system pressure)
  • HAND manual Start – auto Stop / manual Stop (e.g. Servicing)

Control:

  • Compressor solenoid drain valve (NO)
  • Auto-unloaded Start (programmable - ‘normal’ 15 s)
  • Periodic drainage (programmable - ‘normal dry gas’ every 30 min. for 5 s)
  • Feed gas Start / Stop (gas suction pressure sensor control)
  • Suction gas solenoid shut-off valve (NC)(open on Start/close on Stop)
  • Final system Stop / Start(gas final pressure sensor control)

User Interface:

Custom backlit LCD: 2 LED Indicators

-STATUS: Green

-FAULT: Red

Keypad: 7 tactile push buttons

  • START(I)Manual Start
  • STOP (O)Manual Stop
  • RESET (//)Reset and clear faults
  • ESCAPE (C)Step back one level
  • MINUS/DOWN (▼) Scroll down menu
  • PLUS/UP(▲) Scroll up through menu
  • ENTER(◄┘) Confirm selection

Display:

  • Operating gas pressure
  • Hours run
  • Service hours
  • Gas temperature
  • Oil pressure

Error(s) - shutdown/Alarm/Diagnostics:

  • Emergency Stop
  • E-Motor over-load
  • Low oil lubricating pressure
  • Low / high gas suction pressure
  • Oil/water (condensate) level alarm
  • High gas temperature
  • High final gas pressure
  • Potential free contact(s)

Optional equipment:

  • Final receiver packages with the necessary components supplied
  • Diesel motor driven
  • Modified for 50 Hz power supply
  • Customized controls for user specified monitoring and operation
  • Weather resistant canopy
  • Complete package rated for installation in a hazardous location (Class 1 Division 2, or Class 1 Division 1)

Sauer Compressors USA custom engineers solutions for our customers. Please inquire about options you may require which are not listed.