ECOLE DES MINES D’ALBI-CARMAUX
CROMeP
OBSERVATOIRE INTERNATIONAL DES OUTILLAGES
Veille: Outils d’Emboutissage-Découpage
Annee: 2001
Volume: 0112
Références identifiées (24)
Brevets (0)
Néant
Publications (24)
01-24 Cao J., Li S. , Xia Z.C., Tang S.C., Analysis of an axisymmetric deep-drawn part forming using reduced forming steps, Journal of Materials Processing Technology, 117, pp 193-200, November, 2001
001-23 Yang T.-S., Hsu T.-C., Forming limit analysis of hemispherical-punch stretch forming, Journal of Materials Processing Technology, 117, pp 32-36, November, 2001
01-22 Becze C.E., Worswick M.J., Elbestawi M.A., High strain rate shear evaluation and characterization of AISI D2 tool steel in its hardened state, Journal of Machining Science And Technology, 5, 1, 121-149, 2001.
01-21 Doege, E., Elend L.E., Design and application of pliable blank holder systems for the optimization of process conditions in sheet metal forming, Journal of Materials Processing Technology, 111, 182-187, 2001.
01-20 Keum Y.T., Ghoo B.Y., Kim J.H., Application of an expert drawbead model to the finite element simulation of sheet forming processes, Journal of Materials Processing Technology, 111, 155-158, 2001.
01-19 Su Y.L., Kao W.H., Tribological behavior and wear mechanisms of TiC: H/TiC/TiCN/TiN/Ti coatings when sliding againts steel, bronze and aluminium alloy rods, Journal of Material Sciences, 36, 189-199, 2001.
01-18 Niranjan K., Ramamoorthy, B., Tool wear evaluation by stereo vision and prediction by artificial neural network, Journal of Materials Processing Technology, 112, pp 43-52, September, 2001
01-17 Hortig D., Schmoeckel D., Analysis of local loads on the draw die profile with regard to wear using the FEM and experimental investigations, Journal of Materials Processing Technology, 115, pp 153-158, September, 2001.
01-16Pfeifer T., Imkamp D., Glombitza M., Selective measuring of freeform surfaces for quality control and selective maintenance of bending tools, Journal of Materials Processing Technology, 115, pp 147-152, September, 2001.
01-15 Dirksen U., Austerhoff N., Maevus F., Kleiner M., Shape optimization of sheet metal parts in a flexible production environment, Journal of Materials Processing Technology, 115, pp 136-141, September, 2001.
01-14 Tabacaru V., Oancea N., Numerical modelling of the generation of active surfaces of deep drawing dies, Journal of Materials Processing Technology, 115, pp 127-130, September, 2001.
01-13 Bolt P.J., Lamboo N.A.P.M., Rozier P.J.C.M, Feasibility of warm drawing of aluminium products, Journal of Materials Processing Technology, 115, pp 118-121, September, 2001.
01-12Muller H., Sladojevic J., Rapid tooling approaches for small lot production of sheet-metal parts, Journal of Materials Processing Technology, 115, pp 97-103, September, 2001.
01-11 Banabic D., Balan T., Comsa D.-S, Closed-form solution for bulging through elliptical dies, Journal of Materials Processing Technology, 115, pp 83-86, September, 2001.
01-10 Klocke F., Sweeney K., Raedt H.-W., Improved tool design for fine blanking through the application of numerical modeling techniques, Journal of Materials Processing Technology, 115, pp 70-75, September, 2001.
01-9 Gerlach, J., Krasovskyy A., Sester M., How the choice of element types and material laws influences springback simulation results, IDDRG 2001 Working Group Meeting, Espoo, Finland. June, 2001.
01-8 Paris, J.P., A novel procedure for establishing clinching parameters, IDDRG 2001, Working Group Meeting, Espoo, Finland. June, 2001.
01-7 Siegert, K., Control by active drawbeads, IDDRG 2001 Working Group Meeting, Espoo, Finland. June, 2001.
01-6 Pellisetti S., Radlmayr K.M., Investigation of forming properties of semi-finished steel products for hydroforming applications, IDDRG 2001 Working Group Meeting, Espoo, Finland. June, 2001.
01-5 Gantar G., Kuzman K., Tisza M., Environmentally friendly lubrification in sheet metal forming, IDDRG 2001 Working Group Meeting, Espoo, Finland. June, 2001.
01-4 Col A., Presentation of the 3DS Research project, IDDRG 2001 Working Group Meeting, Espoo, Finland, June, 2001.
01-3 Huang Y-M., Chien K-H, Influence of the punch profile on the limitation of formability in the hole-flanging process, Journal of Materials Processing Technology, 113, pp 720-724, April, 2001.
01-2 Konnerth U., A hydraulic high-speed tryout press for the simulation of mechanical forming processes, Journal of Materials Processing Technology, 111, pp 159-163, April, 2001.
01-1 Alinger M.J., Van Tyne C.J., Evolution of the tribological characteristics of several forming die materials, Journal of Materials Processing Technology, 111, pp 20-24, April, 2001.
Rédaction: L. PenazziMise à jour: 27/01/02