The commercial division of USFLOORS INC

3580Corporate Dr. 30721 | 877.292.4044

Citadel Collection™

Construction Document 096429

All references included in this document refer to USFContract as the product manufacturer. Natural Wood™ is a trade brand name represented under the exclusive control of USFloors Inc. of which USFContract is the commercial division.

PART ONE- GENERAL

1.1QUALITY ASSURANCE

  1. Qualifications:
  2. Manufacturer Qualifications:
  3. Use low-VOC and EØ compliant adhesives and finishes in manufacturing of all products.
  4. NAUF Compliance Statement
  5. Minimum five years’ experience in manufacturing and distributing wood flooring of the type specified.
  6. Member: National Wood Flooring Association, United States Green Building Council
  7. Installer Qualifications:
  8. Minimum three years’ experience in hardwood flooring installation
  9. Minimum three years’ experience in installation of hardwood flooring over radiant heating systems
  10. DELIVERY, STORAGE, AND HANDLING
  11. Deliver flooring to project site in original boxes no less than 72 hours prior to start of installation
  12. Open cartons to acclimate.
  13. PROJECT/SITE CONDITIONS
  14. Environmental Requirements: Installation spaces, flooring and adhesive must be maintained at normal occupancy temperature and humidity levels (HVAC working) for minimum 3 days prior to installation.
  15. Installation contractor must test for moisture, as referenced in the installation guidelines, ensuring that moisture content of product relative to subfloor is sufficient for installation (less than 3% moisture content difference between the material and the subfloor installed).
  16. WARRANTY
  17. Lifetime Structural Warranty: This covers the bonding agent process that includes the separation of the wood to wood construction that each board incorporates.

PART TWO- MANUFACTURING - MATERIALS

2.1MANUFACTURER

USFContract

3580 Corporate Drive

Dalton, GA 30721 USA

877-292-4044

2.2 MATERIALS

  1. Acceptable Product:USFContractBASTIAN SERIES
  2. Selection:
  3. AVC3001 Chevalier
  4. AVC3004 Chateau
  5. AVC3006 Segovia
  6. AVC3033 Rochester
  7. Species: 100% FSC certified European White Oak engineered veneer
  8. Texture: Sanded Hand Scraped Rustic Weathered
  9. Size: 7 ½” x 72” x 5/8”
  10. Edge: Tongue and groove with micro-bevel edge channeled backing
  11. Finish: Organic Natural Oil
  12. Physical Property Performance Requirements:
  1. Hardness: ASTM D 1037, Janka Ball
  2. Flammability: ASTM E 648
  3. Smoke Density: ASTM E 622
  4. Slip Resistance: ASTM D 2394 Friction Coefficient
  5. Moisture Content: ASTM D 4442 (varies based on distribution point)
  6. Formaldehyde Emissions: CARB Compliant
  7. Lacey Act Compliance
  8. Substitutions: None Permitted
  1. Acceptable Product: USFContractTOWER SERIES
  1. SKU:
  2. AVC3034 Centurion
  3. AVC3035 Edinburgh
  4. AVC3036 Belcourt
  5. Species: 100% FSC certified European White Oak engineered veneer
  6. Texture: lite wired, smooth raised knots, sculptured, Weathered
  7. Size: 8 ½” x 86 5/8” x 5/8”
  8. Edge: Tongue and groove with micro-bevel edge channeled backing
  9. Finish: Organic Natural Oil
  10. Physical Property Performance Requirements:
  1. Hardness: ASTM D 1037, Janka Ball
  2. Flammability: ASTM E 648
  3. Smoke Density: ASTM E 622
  4. Slip Resistance: ASTM D 2394 Friction Coefficient
  5. Moisture Content: ASTM D 4442 (varies based on distribution point)
  6. Formaldehyde Emissions: CARB Compliant
  7. Lacey Act Compliance
  1. Substitutions: None Permitted
  1. Acceptable Product:USFContractFORTRESS SERIES
  1. Selection:
  2. AVC3002 Nantes
  3. AVC3003 Alcazar
  4. AVC3005 Michel
  5. AVC3007 Auray
  6. AVC3008 Saumur
  7. AVC3009 Blair [w/inlays]
  8. AVC3010 Lucknow [w/inlays]
  9. Species: 100% FSC certified European White Oak engineered veneer
  10. Texture: Thermo-modified Rustic , Weathered
  11. Size: 7 ½” x 72” x 5/8”
  12. Edge: Tongue and groove with micro-bevel edge channeled backing
  13. Finish: Organic Natural Oil
  14. Physical Property Performance Requirements:
  1. Hardness: ASTM D 1037, Janka Ball
  2. Flammability: ASTM E 648
  3. Smoke Density: ASTM E 622
  4. Slip Resistance: ASTM D 2394 Friction Coefficient
  5. Moisture Content: ASTM D 4442 (varies based on distribution point)
  6. Formaldehyde Emissions: CARB Compliant
  7. Lacey Act Compliance
  1. Substitutions: None Permitted
  1. Acceptable Product:USFContractTRAVERSE SERIES
  1. Selection:
  1. AVC3011 Millares
  2. AVC3012 AURELIAN
  3. AVC3013 GENOESE
  1. Species: 100% FSC certified European White Oak engineered veneer
  2. Texture: Thermo-modified Rustic , Weathered
  3. Size: 7 ½” x 72” x 5/8”
  4. Visual: Diagonal visual in the planks
  5. Edge: Tongue and groove with micro-bevel edge channeled backing
  6. Finish: Organic Natural Oil
  7. Physical Property Performance Requirements:
  1. Hardness: ASTM D 1037, Janka Ball
  2. Flammability: ASTM E 648
  3. Smoke Density: ASTM E 622
  4. Slip Resistance: ASTM D 2394 Friction Coefficient
  5. Moisture Content: ASTM D 4442 (varies based on distribution point)
  6. Formaldehyde Emissions: CARB Compliant
  7. Lacey Act Compliance
  1. Substitutions: None Permitted

PART THREE- EXECUTION

3.1EXAMINATION

  1. Examine substrates prior to installation
  2. Verify that subfloor is clean, dry, and free of contaminates that would interfere with adhesive bond.
  3. Concrete installation:

1)Test concrete floors for moisture content using a Calcium Chloride test or Tramex Moisture Encounter meter.

2)Do not install flooring if vapor pressure exceeds 3 lbs per 1,000 sf (15 g per m2) in 24 hours, as under these conditions “urethane” adhesives tend to fail.

3)In multiple story buildings, test each floor level

4)Mark test location(s) on As-Built Drawings

  1. The subfloor moisture content is not to exceed 14% for plywood substrate.
  2. In multiple story buildings, test each floor level
  3. Mark test location(s) on As-Built Drawings.
  4. Verify that HVAC system is operating and maintaining occupancy level temperature and humidity conditions.
  5. If either of the above requires attendance, coordinate with responsible entity to correct unsatisfactory conditions.

3.02 PREPARATION

  1. Acclimatization:
  1. Open all bundles, and let acclimate for a minimum of 72 hours.
  2. Fix the substrate to ensure bumps and depressions are less than 1/8” over 10 feet.

3.03 INSTALLATION

  1. Install in accordance with manufacturer's installation instructions by either:
  1. nailing or stapling to substrate
  2. gluing to substrate
  3. nailing or stapling and gluing to substrate
  4. gluing t/g with cork underlayment
  5. Lay flooring in the direction(s)/pattern(s) as shown on Drawings.
  6. Accessories: Install using methods appropriate to the accessory and flooring system.

3.04 CLEANING

  1. Clean in accordance to Manufacturer’s Maintenance Recommendations.

3.05 PROTECTION

  1. Remove visible adhesive and other surface blemishes using cleaner as recommended.
  2. Do not wash floor for at least five days following installation
  3. When the planks sufficiently seats (in no case less than five days), clean in accordance with USFloors written directions.
  4. After cleaning the flooring surface, it is necessary to protect the floor from mars, indentations, paint drippings, or other damage by either using building paper or by keeping traffic off the floors until the building is ready for occupancy.
  5. Do not use non-breathable sheet or film that could cause condensation to form. Maintain covering throughout remainder of construction period
  6. Should the floors become dirty or damaged prior to final acceptance by the Owner, they shall be repaired, re-cleaned, refinished, or replaced as required so that the Owner will receive floors ready for occupancy without additional cleaning before using.

3.06 OPERATIONS AND MAINTENANCE DOCUMENTS

  1. Apply clean coat refresh or damp mop after install.
  2. Upon completion of floor installation the owner, attendants, or individuals in charge responsible for upkeep of building are to follow care and maintenance instructions.
  3. The General Contractor shall supply original copies of all flooring cleaning and maintenance information provided by USFloors. The Owner’s maintenance personnel must receive this information upon completion of work.

Page 1 of 1

Revised 06-2014