Material Safety Data Sheet

(According to 91/155 EC)

The Argen Corporation

5855 Oberlin Dr., San Diego, CA 92121-4781

SECTION 1 - SUBSTANCE IDENTIFICATION

ALLOY NAME: ARGEDENT 75
DESCRIPTION: / Color: / YELLOW / Type: / PFM

SECTION 2 - COMPOSITON/INFORMATION ON INGREDIENTS

METAL / % / SYMBOL / CAS NO / ACGIH 8 HR TLV / OSHA 8 HR PEL
GOLD / 75.1 / Au / 7440-57-5 / Not established / Not established
PALLADIUM / 12 / Pd / 7440-05-3 / No data / No data
SILVER / 10 / Ag / 7440-22-4 / 0.01 mg/m3 / 0.1 mg/m3
IRIDIUM / x / Ir / 7439-88-5 / No data / No data
INDIUM / 1.8 / In / 7440-74-6 / 0.1 mg/m3 / 0.1 mg/m3 TWA
TIN / 1 / Sn / 7440-31-5 / 2 mg/m3 / 2 mg/m3

Note: % values are in weight percent and reflect nominal composition.

Note: 'x' denotes a content of less than one percent

SECTION 3- HAZARDS IDENTIFICATION

EYES: / Contact with eyes may cause severe irritation and possible eye burns.
SKIN: / May cause severe irritation and possible burns.
INGESTION: / May cause gastrointestinal irritation with nausea, vomiting, and diarrhea.
INHALATION: / May cause irritation and burns to the respiratory tract.
NOTE: / Exposure levels for elements in this alloy are listed in SECTION 2. The following health data is for specific elements:
SILVER / Absorption of silver compounds by ingestion, inhalation or through broken skin can cause argyria, a permanent bluish-grey discoloration of the skin, conjuctiva and mucous membrains. Generalized argyria develops after 2 to 25 years of exposure. There are no systematic effects or symptoms and no physical disability. Silver is considered an experimental equivocal tumorigenic agent by RTECS criteria.
INDIUM / May cause fetal effects based upon animal studies. May cause lung damage and blood abnormalities. Target Organs: Blood, kidneys, liver, lungs.

SECTION 4 - FIRST AID MEASURES

EYE CONTACT : / Immediately flush eyes with plenty of water for at least 15 minutes, occasionally lifting the upper and lower lids.
SKIN CONTACT: / Scrub skin thoroughly with soap and water.
INGESTION: / If victim is conscious and alert, give 2-4 cupfuls of milk or water. Induce vomiting. **Never give anything by mouth to an unconscious person. Get medical aid.
INHALATION: / Remove affected person to fresh air and assist with additional oxygen if necessary. Get first aid if other symptoms appear.

SECTION 5 - FIREFIGHTING MEASURE

This material is fire and explosion resistant. Heating Beyond the melting range may generate fumes which are not flammable.

SECTION 6 - ACCIDENTAL RELEASE MEASURES

GENERAL INFORMATION: Use proper personal protective equipment as described in section 8.

SECTION 7 - HANDLING AND STORAGE

Avoid inhilation of fumes while melting and dust while grinding. Wash hands thoroughly before eating or smoking to avoid ingestion.

SECTION 8 - EXPOSURE CONTROLS/PERSONAL PROTECTIONS

RESPIRATORY: / Provide general ventilation and local exhaust to keep levels below the TLV stated in SECTION 2. Wear a NIOSH approved respirator for dust exceeding the TLVs.
HAND: / Latex gloves are recommended while grinding, heat resistant gloves should be worn while casting and handling hot metals or molds.
EYE PROTECTION: / Wear eye protection suitable to each individual operation.
OTHER: / Wear apron, lab coat or other protective clothing.

SECTION 9 - PHYSICAL AND CHEMICAL PROPERTIES

Appearance: / YELLOW
Odor: / Not Applicable
pH: / Not Applicable
Boiling Point: / Not Applicable
Melting Range: / 1175-1205 ºC
Flash Point: / Not Applicable
Flammability: / Not Applicable
Autoflammability: / Not Applicable
Explosive Properties: / Not Applicable
Oxidizing Properties: / Not Applicable
Vapor Pressure: / Not Applicable
Relative Density: / 16.2 g/cm3
Solubility(Water/Fat): / Insoluble

SECTION 10 - STABILITY AND REACTIVITY

At ordinary and high (below the melting range) temperatures, the material oxidizes but is stable. At very high temperatures the alloy produces fumes.

SECTION 11 - TOXICOLOGICAL INFORMATION

No specific instructions.

SECTION 12 - ECOLOGICAL INFORMATION

This is an environmentally friendly material. With proper dust collecting equipment, 100% of this alloy can be recycled.

SECTION 13 - DISPOSAL CONSIDERATIONS

Whenever possible, recover dust because it has economic value.

SECTION 14 - TRANSPORT INFORMATION

No specific instructions.

SECTION 15 - REGULATORY INFORMATION

No specific instructions.

SECTION 16 - OTHER INFORMATION

The information and recommendations set forth herein (hereinafter "information") are presented in good faith and believed to be correct as of the date hereof. However, The Argen Corporation makes no representations as to the completeness of accuracy thereof and information is supplied upon the condition that the persons receiving the above material will make there own determination as to its suitability for their purposes prior to use. In no event will "The Argen Corporation" be responsible for damages of any nature whatsoever resulting from the use of or reliance upon information. No representations or warranties, either expressed or implied, or merchantability, fitness for a particular purpose or of any other nature are made hereunder with respect to information or the product to which information refers.

MSDS Creation Date: 4/11/1997