109 Iber RoadDOOR HARDWARESection 08 71 00
Project N° 2014777Page 1
PART 1 - GENERAL
1.1 RELATED SECTIONS.1Section 08 11 00 - Metal Doors and frames
.2Section 08 11 16 - Aluminum Doors and Frames
.3Section 08 14 16 - Flush Wood doors
1.2 REFERENCES.1Canadian Steel Door and Frame Manufacturers’Association
(CSDFMA).
.2CSDFMA Canadian Metric Guide for Steel Doors and Frames
(Modular Construction: Standard hardware location
dimensions, or as indicated for special conditions.
.3CAN CSA B-651-12 Accessible Design for the Built
Environment.
.4American National Standards Institute / Builders
Hardware Manufacturers Association:
.1ANSI/BHMA A156.1-2006
Butts and Hinges.
.2ANSI/BHMA A156.2-2011
Bored and Preassembled Locks and Latches.
.3ANSI/BHMA A156.4-2008
Door Controls - Closers.
.4ANSI/BHMA A156.6-2010
Architectural Door Trim.
.5ANSI/BHMA A156.8-2005
Door Control - Overhead Stops and Holders.
.6ANSI/BHMA A156.16-2008
Auxiliary Hardware.
.7ANSI/BHMA A156.18-2006
Materials and Finishes.
.8ANSI/BHMA A156.21-2009
Thresholds.
.9ANSI/BHMA A156.22-2005
Door Gasketing and Edge Seal Systems.
.10ANSI/BHMA A156.26-2006
Continuous Hinges.
.11ANSI/BHMA A156.36-2010
Auxiliary Locks.
1.3 SUBMITTALS.1Product Data:
.1Submit manufacturer’s printed product literature,
specifications and data sheets indicating hardware
proposed, including ANSI function where ANSI used in
this specification, grade, type, series, BHMA finish, fire
label listing, in accordance with Section 01 00 10 –
General Instructions.
.2Samples:
.1Submit samples of each type of hardware
specified in accordance with Section 01 00 10 –
General Instructions.
.2Identify each sample by label indicating applicable
specification paragraph number, brand name and
number, finish and hardware package number.
.3After approval samples will be returned for
incorporation in the Work.
.3Hardware List:
.1Submit a typewritten Finishing Hardware schedule in
accordance with Section 01 00 10 – General
Instructions.
.2Indicate specified hardware, including make, model,
base material, function, size, finish and other pertinent
information.
.4Manufacturer’s Instructions:
.1Submit manufacturer’s installation instructions.
.5Closeout Submittals:
.1Provide operation, maintenance data, parts list and
manufacturer’s instructions for each type of locksets,
door closers and door holders for incorporation into
manual specified in Section 01 00 10 – General
Instructions.
1.4 QUALITY ASSURANCE.1Regulatory Requirements:
.1Use hardware for doors in fire separations and exit
doors certified by a Canadian Certification organization
accredited by Standards Council of Canada.
.2All fire and life safety codes shall be met as required by the
authority having jurisdiction.
.3Use lock and latchsets with lever handles meeting
requirementsof CAN/CSA- B651, Barrier Free Design, unless
specifiedotherwise.
.4Pre-installation Meetings: conduct pre-installation meeting to
verify project requirements, manufacturer’s installation
instructions and manufacturer’s warranty requirements.
.5It shall be clearly understood that within the terms of this
Subcontract, the Door Hardware Supplier is bound not just as a
supplier, but as a Subcontractor and is responsible for the
supply of Project services relative to project co-ordination,
supervision and inspection.
.6No claims for extra money will be entertained if such claims are
from lack of co-ordination between the Door Hardware
Subcontractor and any other Subcontractor. Ensure that Work
of other Subcontractors, as it proceeds, will accommodate the
installation of hardware.
.7Attend site meetings as requested by the Contractor.
1.5 DELIVERY, STORAGE.1Packing, Shipping, Handling and Unloading:
AND HANDLING.1Deliver, store, handle and protect materials in
accordance with Section 01 00 10 – General
Instructions.
.2Package each item of hardware including fastenings,
separately or in like groups of hardware, label each
package as to item definition and location.
.2Storage and Protection:
.1Store finishing hardware in locked, clean and dry area.
1.6 WASTE DISPOSAL.1Separate and recycle waste materials in accordance with
AND MANAGEMENTSection 01 00 10 – General Instructions.
.2Remove from site and dispose of all packaging materials at
appropriate recycling facilities.
.3Dispose of all packaging material in appropriate on-site bin for
recycling in accordance with site waste management program.
1.7 MAINTENANCE.1Extra Materials:
.1Provide maintenance materials in accordance with
Section 01 00 10 – General Instructions.
.2Supply two sets of wrenches for locksets, and door
closers.
PART 2 – PRODUCTS
2.1 HARDWARE ITEMS.1Door hardware, as specified, to be certified to ANSI/BHMA
standards.
.2Use one manufacturer’s products only for all similar items.
.3Acceptable Materials: Where materials are specified by trade
name refer to the Instructions to Tenderers for procedure to be
followed in applying for approval of alternates.
2.2 DOOR HARDWARE.1Butts and Hinges shall comply with ANSI/BHMA A156.1
.1A8112 - steel base metal, full mortise, exposed
anti-friction ball bearing, grade 2, standard weight.
.2Supply 1-1/2 pair per door leaf for doors up to 2285mm
in height. Supply one additional hinge for each
additional 762mm of height or fraction thereof. Doors,
45mm thickness, up to 914mm in width, supply 114mm
high hinges; over 914mm to 1220mm, supply 127mm
high hinges.
.3NRP - non removable pin.
.4Hinges listed are by Hager.
Stanley equivalents are acceptable.
Hager Stanley
BB1279 FBB179
.2Continuous Hinges shall comply with ANSI/BHMA A156.26
.1Continuous hinges for aluminum doors shall be
aluminum material, gear type, edge mount, heavy duty,
minimum thirty- two thrust bearings, staggered screw
holes. Leafs should not extend fully across both the
frame rebate and the edge of exterior aluminum door
thus reducing transfer of cold.
.2Factory cut, maintaining three rows of two screws (six
total) at both top and bottom, to length required for door
height. Length to match door height. 12.7mm of door
heel exposure is acceptable. For exterior door
application the length should be reduced to allow
installation of the door sweep across the full width of
theexterior door face without interfering with the hinge
knuckle.
.3Hager Roton continuous hinges 780-112 HD series
listed for aluminum doors.
.3Bored and Preassembled Locks and Latches, shall comply with
ANSI/BHMA A156.2
.1Medium duty cylindrical type, 2 grade.
1. Schlage A series, Orbit (ORB) knob design. No
substitution.
.2Medium duty cylindrical type, 2 grade.
1. Schlage AL series, Saturn (SAT) lever
design. No substitution.
2. Function as specified.
.4Door Pulls shall comply with ANSI/BHMA A156.6
.1Type J402: 25.4mm round diameter, ‘D’ shape, 90
degree offset, 304.8mm centres. Type 304 stainless
steel material.
Standard MetalGallery C.B.H.
3012-21180-2 7009-1”
.5Push Bars shall comply with ANSI/BHMA A156.6
.1Type J501: 25.4mm round diameter, ‘D’ shape. To
extend horizontally across push side face of doors
centered on door stiles. Centres to be confirmed.
Type 304 stainless steel material.
Standard MetalGallery C.B.H.
6000-25000-2 7040-1”
.6Door Controls - Closers shall comply with ANSI/BHMA A156.4
.1Heavy duty. Full rack and pinion hydraulic action. Cast
iron cylinder body. Non-sized fully adjustable spring
power and back check. Full plastic cover.
.2LCN 4010, 4020 & 4110 series. No substitution.
.3DEL – delayed action.
.4Provide adapter plates as required for proper
installationof door closers.
.7Architectural Door Trim. Kick plates shall comply with
ANSI/BHMA A156.6
.1Type J102: 1.27mm material thickness. Bevelled edges.
Height as specified x length to suit.
Standard Metal Gallery C.B.H. Hager
K10A 80A903 190S
.8Door Control - Overhead Stops and Holders shall comply with
ANSI/BHMA A156.8
.1Type 1 heavy duty overhead concealed slide type.
Glynn-Johnson 100 series. No substitution.
.2 All listed degrees of hold open should be reviewed and
confirmed before preparation and/or installation.
.9Floor and Wall stops shall comply with ANSI/BHMA A156.16.
.1Cast brass or bronze material except where specified
zinc die cast.
.2Rear portion of heavy duty one piece cast floor stops
shall have a stud to prevent rotation. Rise to suit door
undercut.
.3Wall stop shall have a metal back plate secured to wall
with (2) screws and shields. Housing and rubber insert
fits over back plate and is secured with inconspicuous
allen set screw on side of housing. No screws or holes
shall be visible on face of bumper.
.10Threshold shall comply with ANSI/BHMA A156.21
.1Extruded aluminum. Oversized in length to allow
copingaround exterior pressed steel frame faces.
Width tosuit jamb and floor conditions.
.11Threshold Lip shall comply with ANSI/BHMA A156.21
.1Aluminum c/w silicone insert. Applied to surface of flat
threshold against inside face of door.
.12Door Sweep shall comply with ANSI/BHMA A156.22
.1Aluminum extrusion c/w insert of black nylon bristles.
Applied to pull side face of door. Predrilled with oblong
holes for adjustment. Length to suit width of door.
.2 K.N. Crowder as specified to match standards of
acceptance. No substitution.
.3Product # W-24S, aluminum extrusion c/w black nylon
bristles.
.13Weatherstripping shall comply with ANSI/BHMA A156.22
.1Extruded aluminum with silicone insert. Predrilled with
oblong screw holes for adjustment. Designed to provide
continuous weather seal. Surface hardware to be
attached to frame through weatherstrip section.
Confirm frame stop width sufficient to support 38.1±mm
wide extrusion. Provide shim as required.
K.N. Crowder: W-20S
.223mm wide extruded aluminum ‘L’ profile with silicone
insert. Predrilled with oblong screw holes for
adjustment.
K.N. Crowder: W-16S
.14Auxiliary Locks shall comply with ANSI/BHMA A156.36-2010
.1Narrow stile locks. Key on outside, paddle on inside
retracts latch bolt. Auxiliary dead latch. Latch bolt is
held retracted when so actuated.
2.3 KEYING.1The Door Hardware Supplier shall prepare a detailed keying
schedule in co-operation with the Project Manager.
.2All locks shall be keyed into a new Schlage keying system as
follows:
- construction master keyed
- master keyed
- keyed alike or different as required.
.3Supply (2) change keys per cylinder.
Supply (4) construction master keys
Supply (2) extractor keys
Supply (3) master keys per group.
.4All permanent keys are to be delivered directly to the Project
Manager.
.5All cylinders are to be supplied with cams / tailpieces suitable
for specified lock functions. Supply all compression rings, trim
collars and blocking rings to suit.
.6The Contractor is responsible for providing locks and cylinders
as required for his own use during the period of construction.
2.4 FASTENINGS.1All hardware is to be installed using manufactures’ supplied
fasteners. Failure to comply may void warranties and
applicable licensed labels. Self tapping/tek screws will not be
acceptable on this project.
.2Supply screws, bolts, expansion shields and other fastening
devices required for satisfactory installation and operation of
hardware.
.3Exposed fastening devices to match finish hardware.
.4Kick plates are to be supplied with self adhesive tape, except
where noted, then supply countersunk, oval head, flush
mounting socket screws to suit door material.
2.5 FINISHES.1Materials and Finishes shall comply with ANSI/BHMA A156.18
Hinges628clear anodized aluminum
652satin chromium plating on steel
Locksets 626satin chromium plated
Deadlatch & Paddle628clear anodized aluminum
Door Pull630stainless steel, satin
Push Bar630stainless steel, satin
Door Closers689powder coat aluminum
SRIspecial rust inhibitor
Kick Plates630satin stainless steel
Overhead Stops630stainless steel, satin
Floor/Wall Stops626satin chrome
Threshold &ALclear anodized aluminum
Weatherstripping
2.6 ABBREVIATIONSALDaluminum door
T.B. ALFthermally broken aluminum frame
HMDhollow metal door
INS. Insulated hollow metal door
PSFpressed steel frame
SCWDsolid core wood door
LHleft hand
RHright hand
LHRleft hand reverse
RHRright hand reverse
PART 3 EXECUTION
3.1 MANUFACTURER’S .1Compliance: comply with manufacturer’s written data, including
INSTRUCTIONSproduct technical bulletins, product catalogue installation
instructions, product carton installation instructions and data
sheets.
.2When requested, furnish metal door and frame manufacturers
with complete instructions and templates for preparation of
theirwork to receive hardware.
.3Furnish manufacturer’s instructions for proper installation of
each hardware component.
3.2 INSTALLATION.1Install hardware to standard hardware location dimensions in
accordance with Canadian Metric Guide for Steel Doors and
Frames (Modular Construction) prepared by Canadian Steel
Door and Frame Manufacturers’ Association, or as indicated
forspecial conditions.
.2Only tradesmen competent in the installation of Finishing
Hardware shall be used for this purpose. Qualification would
require a minimum (5) years experience in commercial
application. The installer shall adjust, clean and make good all
installation of Finishing Hardware to the satisfaction of the
Project Manager.
.3Kick plates are to be installed 1.59mm maximum up from the
bottom edge of door push side. On single doors install in the
centre of the door equally spaced to clear between the frame
jamb stops and/or gasketing.
.4Thresholds are to be extended from masonry opening to
masonry opening and are to be coped around the pressed
steelframes. Installer to caulk threshold base to ensure proper
seal.
.5Weatherstripping is not to be installed until final coat of paint
has been applied to the door and frame and is completely dry.
.6Door Supplier, when templating, must consider surface
mounted w/stripping which is 8.0±mm thick. Door closer
parallel arm brackets and overhead stop/holder brackets will
mount on top of the weatherstripping.
3.3 ADJUSTING.1Adjust door hardware for optimum, smooth operating condition,
safety and for weather tight closure.
.2Lubricate hardware, operating equipment and other
moving parts.
.3Adjust door hardware to provide tight fit at contact points with
frames.
3.4 CLEANING.1Perform cleaning after installation to remove construction and
accumulated environmental dirt.
.2Clean hardware with damp cloth and approved non- abrasive
cleaner. Polish hardware in accordance with manufacturer’s
instructions.
.3Remove protective material from hardware items where
present.
.4Upon completion of installation, remove surplus materials,
rubbish, tools and equipment barriers.
3.5 DEMONSTRATION.1Maintenance Staff Briefing:
.1Brief maintenance staff regarding:
.1 Proper care, cleaning and general maintenance
of projects complete hardware.
.2Description, use, handling, and storage of keys.
.3Use, application and storage of wrenches for
locksets, exit devices and door closers.
.2Demonstrate operation, operating components,
adjustment features and lubrication requirements.
3.6 INSPECTIONS.1 The Door Hardware Supplier shall make periodic site
inspections during installation of hardware to ensure that all
hardware supplied is being applied in accordance with
specifications, details and Architect’s directions. Inform the
Contractor and the Architect in writing of such inspections,
pointing out errors, omissions, etc.: so that same may be
corrected.
.2 The Door Hardware Supplier will contact product
representatives (locksets, exit devices and door closers) who
will also make inspections during construction to ensure the
proper installation and adjustment of their products. Final
inspection to be carried out by Door Hardware Supplier and
Product Representative. Representative to provide written
certification that hardware has been installed and adjusted as
intended.
3.7 HARDWARE SCHEDULE.1 The following is a list of hardware to be used to define required
standards on this project. Acceptable alternates as listed.
Additional alternates subject to review and written acceptance
prior to submission, within the allotted time period, of the
Tender closing. Substitutions without prior approval will not be
accepted in the shop drawing submission.
ITEM #11 SGLE DOOR D01EXTERIOR FROM RENTAL SPACE (G) 16LHR
ITEM #21 SGLE DOOR D04EXTERIOR FROM RENTAL SPACE (A) 02LHR
ITEM #31 SGLE DOOR D08EXTERIOR FROM RENTAL SPACE (C) 07LHR
ITEM #41 SGLE DOOR D10EXTERIOR FROM RENTAL SPACE (D) 10LHR
ITEM #51 SGLE DOOR D14EXTERIOR FROM RENTAL SPACE (D) 10LHR
ITEM #61 SGLE DOOR D18EXTERIOR FROM RENTAL SPACE (F) 14LHR
914x 2134 x 45ALD/ALF
TYPEALUMICOR 500B
6EACONT. HINGE780-112 HD628
6EAar DEADLATCH4510-4 (38.1mm BACKSET) x 4902-01 STRIKE628
x 4902-01 STRIKE
c/w FACEPLATE SHAPE TO SUIT EDGE OF DOOR
6EALATCH PADDLE4590628
INSTALL CENTRED ON DOOR PULL
6EACYLINDER20-013626
6SETPULL/PUSH3012-2 + 6000-2 CONFIRM CENTRES630
#5 B TO B MTG. @ TOP COMMON END
x #5 SGLE MTG. x RIVNUT
c/w 2 (DOUBLE) SET SCREWS FOR EACH POST
6EADOOR CLOSER4020SRI689
CONFIRM REVEAL AND LONG ARM REQUIREMENT
6EAADAPTER PLATE4020-18GSRI689
6EAO/H STOPGJ104S x 95 DEGREE630
T.B. THRESHOLDBY DOOR AND FRAME SUPPLIER
W/STRIPPINGBY DOOR AND FRAME SUPPLIER
6EADOOR SWEEPW-24S x 914mm (EXTERIOR SIDE)AL
ITEM #71 SGLE DOOR D02EXTERIOR FROM MECHANICAL ROOM 01LHR
914x 2134 x 45INS. HMD/T.B. PSF
TYPE HM 1/PS 1
1EACONT. HINGE780-112628
1EADEADLOCKB560P626
1EALATCHSETA10S ORB626
1EADOOR CLOSER4111 EDA x 62G SHOE & BENT ARM x MSSRI 689
SEE SPECIAL TEMPLATEST-2730
1EAKICK PLATEK10A 203.2 x 863mm x MS630
1EAO/H STOP/HOLDGJ904H x 90 DEGREE630
1LENTHRESHOLDCT-45 x CT-41-1 x 1016mmAL
1LENTHRESHOLD LIPCT-40S x 914mmAL
1EADOOR SWEEPW-24S x 914mmAL
2 LENW/STRIPPING W-16S x 2134mm (JAMBS) AL
1LENWSTRIPPINGW-20S x 914mm(HEAD)AL
INSTALL BEFORE DOOR CLOSER & O/H STOP/HOLDER
ITEM #81 SGLE DOOR D03EXTERIOR FROM RENTAL SPACE (A) 02RHR
ITEM #91 SGLE DOOR D07EXTERIOR FROM RENTAL SPACE (B) 04RHR
ITEM #101 SGLE DOOR D11EXTERIOR FROM RENTAL SPACE (D) 10RHR
ITEM #111 SGLE DOOR D15EXTERIOR FROM RENTAL SPACE (D) 10RHR
ITEM #121 SGLE DOOR D17EXTERIOR FROM RENTAL SPACE (E) 11RHR
ITEM #131 SGLE DOOR D21EXTERIOR FROM RENTAL SPACE (G) 16RHR
914x 2134 x 45ALD/ALF
TYPEALUMICOR 500B
6EACONT. HINGE780-112 HD628
6EAar DEADLATCH4510-4 (38.1mm BACKSET) x 4902-01 STRIKE628
x 4902-01 STRIKE
c/w FACEPLATE SHAPE TO SUIT EDGE OF DOOR
6EALATCH PADDLE4590628
INSTALL CENTRED ON DOOR PULL
6EACYLINDER20-013626
6SETPULL/PUSH3012-2 + 6000-2 CONFIRM CENTRES630
#5 B TO B MTG. @ TOP COMMON END
x #5 SGLE MTG. x RIVNUT
c/w 2 (DOUBLE) SET SCREWS FOR EACH POST
6EADOOR CLOSER4020SRI689
CONFIRM REVEAL AND LONG ARM REQUIREMENT
6EAADAPTER PLATE4020-18GSRI689
6EAO/H STOPGJ104S x 95 DEGREE630
T.B. THRESHOLDBY DOOR AND FRAME SUPPLIER
W/STRIPPINGBY DOOR AND FRAME SUPPLIER
6EADOOR SWEEPW-24S x 914mm (EXTERIOR SIDE)AL
ITEM #141 EA DOOR D05EXTERIOR / RENTAL SPACE (A) 02
ITEM #151 EA DOOR D06EXTERIOR / RENTAL SPACE (B) 04
ITEM #161 EA DOOR D09EXTERIOR / RENTAL SPACE (C) 07
ITEM #171 EA DOOR D12EXTERIOR / RENTAL SPACE (D) 10
ITEM #181 EA DOOR D13EXTERIOR / RENTAL SPACE (D) 10
ITEM #191 EA DOOR D16EXTERIOR / RENTAL SPACE (E) 11
ITEM #201 EA DOOR D19EXTERIOR / RENTAL SPACE (F) 14
ITEM #211 EA DOOR D20EXTERIOR / RENTAL SPACE (G) 16
3000x 3200 x 50
TYPEOVERHEAD DOOR
HARDWARE COMPLETE BY DOOR AND FRAME SUPPLIER
ITEM #221 SGLE DOOR D22RENTAL SPACE (A) 02 TO W/R 01 03LH
ITEM #231 SGLE DOOR D23RENTAL SPACE (B) 04 TO W/R 02 05LH
ITEM #241 SGLE DOOR D24RENTAL SPACE (C) 07 TO W/R 03 06RH
ITEM #251 SGLE DOOR D25RENTAL SPACE (D) 10 TO W/R 04 08RH
ITEM #261 SGLE DOOR D26RENTAL SPACE (D) 10 TO W/R 05 09LH
ITEM #271 SGLE DOOR D27RENTAL SPACE (E) 11 TO W/R 06 12LH
ITEM #281 SGLE DOOR D28RENTAL SPACE (F) 14 TO W/R 07 13RH
ITEM #291 SGLE DOOR D29RENTAL SPACE (G) 16 TO W/R 08 15RH
914x 2134 x 45SCWD/PSF
TYPE
24EAHINGEBB1279 114 x 101mm652
8EAPRIVACY SETAL40 SAT626
8EAKICK PLATEK10A 203.2 x 876mm x TAPE630
8EAFLOOR STOPS101626
END OF SECTION
END OF SECTION