Then, Choose

For Back Inlet OR For Bottom Inlet

Fit off stop tap then connect rear water inlet valve to stop Remove cap from cistern plug A or B at base cistern.

tap. Fill cistern and ensure correct water level. Connect flexible hose to cistern plug A or B

depending on location of stop tap. Complete stop

tap connection to underside of cistern plug A or B.

Fill cistern and ensure correct water level.

Note: Inlet valve can be adjusted if required.

Finally,

Secure cistern to pan by installing nuts and washers from the cavity behind the pan before fitting cistern. Place rubber seal into pan recess (do not use sealant). Place cistern screws into holes on the inside of cistern, making sure washers are located correctly. Gently lower cistern onto pan locating fixing screws into matching pan screw holes. Before tightened fully make sure cistern sits square and straight to pan. Ensure that the toilet is level and aligns to the wall before fixing pan to floor using silicon to seal the pan (optional).

Installation Manual

suitable for the model: KN212-3

CAUTION:
The installation must be carried out by a licensed plumber to comply with the product warranty. Install shutoff value before installing toilet. Please handle with care to avoid personal injury or product damage. It is also important to inspect the toilet before installation.

Made BY:

Aurora International Trading Pty Ltd

Website: http://www.aurora.id.au

E-Mail:

PO Box 2011 Rangeview, Mitcham, Victoria 3132, Australia

Product Support Line: 03 9872 4399

Fax: 03 9872 4808

KN212-3

Washdown Close-Coupled Closet

Size: 665mm x 375mm x 825mm

S-Trap: 70-170mm Roughing-in

P-Trap: 180mm Roughing in

Back Inlet: 90mm from centre, 750mm from bottom.

Soft Closing Seat

4.5/3 Liters Dual Flush suite with a WELS 4 Star Rating

NOTE: The actual size and weight may slightly vary due to production craftsmanship. It is highly recommended to measure the actual product before installation. The unit of measure is based on millimeter.

Cleaning Recommendations

It is recommended that toilet seat and cover be installed after all trades are finished. The high quality vitreous china finish on all sanitary ware can be maintained by simply using mild soapy water and wiping over. Sanitary ware should not be cleaned with abrasive materials e.g. steel wool/scourers. Do not use any corrosive or abrasive cleaning agents containing acids or scouring agents as this may lead to surface damage. Bleaches can also discolor seats and hinges and therefore should not be used. If your toilet has metal hinges they should only be cleaned with a mild liquid domestic cleaner, with soft soapsuds or steel $ Chrome cleaner, after cleaning, rinse with clean water and polish with a clean soft cloth.

Installation Guide

First, choose either one of 2 following trap connections opinions to install according to the actual situations.

·  For wall-faced toilet suite with S trap connector

Please measure existing toilet pan to cut the S trap connector. Different toilet suite may have different set out.

Step: 1. Lubricate the fins of the pan bend and position into waste pipe.

2. Lubricate rubber on the exposed connector end.

3. Align and push fully assembled toilet back to the wall

Note: Note: Please make sure to screw the wall brace to the wall to secure the stability of the toilet. If cut is needed, please make sure cut the right proportion according to the ring.

After Cutting

Please make sure to clean the trap after cutting finished, the bits may cause leaking.

·  For wall-faced toilet suite P trap setup

Please measure existing toilet pan to setup P trap from wall to spigot distance. Different toilet suite may have different set out.

Step: 1. Set up waste pipe so that the end of the pan collar extends approx. minimum of 50mm onto spigot.

2. Align and push fully assembled toilet back to the wall, connecting pan spigot to pan collar. Bucket flush and check for leaks.

: The actual distance varies. Make sure to measure it before installation.