Summary:
Symbols involved:
BUF symbol "XLXI_304/IBUF" (Output Signal = W_BUSB<14>)
TBUF symbol "XLXI_304/OBUFT" (Control Signal = notXRD)
PAD symbol "XD_14" (Pad Signal = XD_14)
Component type involved: IOB
Site Location involved: H18
Site Type involved: DIFFSI_NDT
Mapping completed.
See MAP report file "TopLevelController3AN_map.mrp" for details.
Problem encountered during the packing phase.
Design Summary
------
Number of errors : 1
Number of warnings : 2
Process "Map" failed
Started : "Translate".
Running ngdbuild...
Command Line: ngdbuild -intstyle ise -dd _ngo -nt timestamp -uc TopLevelController3AN.ucf -p xc3s700an-fgg484-5 "TopLevelController3AN.ngc" TopLevelController3AN.ngd
Command Line: C:\Xilinx\14.7\ISE_DS\ISE\bin\nt64\unwrapped\ngdbuild.exe
-intstyle ise -dd _ngo -nt timestamp -uc TopLevelController3AN.ucf -p
xc3s700an-fgg484-5 TopLevelController3AN.ngc TopLevelController3AN.ngd
Reading NGO file "C:/Users/Ted/Documents/ISE14_7/Martinez Controller with
3AN/TwelveAMMcontroller3AN/TopLevelController3AN.ngc" ...
Gathering constraint information from source properties...
Done.
Annotating constraints to design from ucf file "TopLevelController3AN.ucf" ...
Resolving constraint associations...
Checking Constraint Associations...
Done...
Checking expanded design ...
Partition Implementation Status
------
No Partitions were found in this design.
------
NGDBUILD Design Results Summary:
Number of errors: 0
Number of warnings: 0
Writing NGD file "TopLevelController3AN.ngd" ...
Total REAL time to NGDBUILD completion: 2 sec
Total CPU time to NGDBUILD completion: 2 sec
Writing NGDBUILD log file "TopLevelController3AN.bld"...
NGDBUILD done.
Process "Translate" completed successfully
Started : "Map".
Running map...
Command Line: map -intstyle ise -p xc3s700an-fgg484-5 -cm area -detail -ir off -pr off -c 100 -ntd -o TopLevelController3AN_map.ncd TopLevelController3AN.ngd TopLevelController3AN.pcf
Using target part "3s700anfgg484-5".
Mapping design into LUTs...
WARNING:MapLib:701 - Signal CLKinA connected to top level port CLKinA has been
removed.
WARNING:LIT:176 - Clock buffer is designated to drive clock loads. BUFGMUX
symbol "physical_group_CLK2_01_250/XLXI_406/COUNT_3_BUFG" (output
signal=CLK2_01_250) has a mix of clock and non-clock loads. The non-clock
loads are:
Pin CE of XLXI_1243
Running directed packing...
ERROR:Pack:1107 - Pack was unable to combine the symbols listed below into a
single IOB component because the site type selected is not compatible.
Further explanation:
The component type is determined by the types of logic and the properties and
configuration of the logic it contains. In this case an IO component of type
IOB was chosen because the IO contains symbols and/or properties consistent
with output or bi-directional usage and contains no other symbols or
properties that require a more specific IO component type. Please double
check that the types of logic elements and all of their relevant properties
and configuration options are compatible with the physical site type of the
constraint.
Summary:
Symbols involved:
BUF symbol "XLXI_304/IBUF" (Output Signal = W_BUSB<14>)
TBUF symbol "XLXI_304/OBUFT" (Control Signal = notXRD)
PAD symbol "XD_14" (Pad Signal = XD_14)
Component type involved: IOB
Site Location involved: H18
Site Type involved: DIFFSI_NDT
ERROR:Pack:1107 - Pack was unable to combine the symbols listed below into a
single IOB component because the site type selected is not compatible. The
symbols have incompatible LOC attributes.
Mapping completed.
See MAP report file "TopLevelController3AN_map.mrp" for details.
Problem encountered during the packing phase.
Design Summary
------
Number of errors : 2
Number of warnings : 2
Process "Map" failed
Started : "Translate".
Running ngdbuild...
Command Line: ngdbuild -intstyle ise -dd _ngo -nt timestamp -uc TopLevelController3AN.ucf -p xc3s700an-fgg484-5 "TopLevelController3AN.ngc" TopLevelController3AN.ngd
Command Line: C:\Xilinx\14.7\ISE_DS\ISE\bin\nt64\unwrapped\ngdbuild.exe
-intstyle ise -dd _ngo -nt timestamp -uc TopLevelController3AN.ucf -p
xc3s700an-fgg484-5 TopLevelController3AN.ngc TopLevelController3AN.ngd
Reading NGO file "C:/Users/Ted/Documents/ISE14_7/Martinez Controller with
3AN/TwelveAMMcontroller3AN/TopLevelController3AN.ngc" ...
Gathering constraint information from source properties...
Done.
Annotating constraints to design from ucf file "TopLevelController3AN.ucf" ...
Resolving constraint associations...
Checking Constraint Associations...
Done...
Checking expanded design ...
Partition Implementation Status
------
No Partitions were found in this design.
------
NGDBUILD Design Results Summary:
Number of errors: 0
Number of warnings: 0
Writing NGD file "TopLevelController3AN.ngd" ...
Total REAL time to NGDBUILD completion: 2 sec
Total CPU time to NGDBUILD completion: 2 sec
Writing NGDBUILD log file "TopLevelController3AN.bld"...
NGDBUILD done.
Process "Translate" completed successfully
Started : "Map".
Running map...
Command Line: map -intstyle ise -p xc3s700an-fgg484-5 -cm area -detail -ir off -pr off -c 100 -ntd -o TopLevelController3AN_map.ncd TopLevelController3AN.ngd TopLevelController3AN.pcf
Using target part "3s700anfgg484-5".
Mapping design into LUTs...
WARNING:MapLib:701 - Signal CLKinA connected to top level port CLKinA has been
removed.
WARNING:LIT:176 - Clock buffer is designated to drive clock loads. BUFGMUX
symbol "physical_group_CLK2_01_250/XLXI_406/COUNT_3_BUFG" (output
signal=CLK2_01_250) has a mix of clock and non-clock loads. The non-clock
loads are:
Pin CE of XLXI_1243
Running directed packing...
ERROR:Pack:1107 - Pack was unable to combine the symbols listed below into a
single IOB component because the site type selected is not compatible.
Further explanation:
The component type is determined by the types of logic and the properties and
configuration of the logic it contains. In this case an IO component of type
IOB was chosen because the IO contains symbols and/or properties consistent
with output or bi-directional usage and contains no other symbols or
properties that require a more specific IO component type. Please double
check that the types of logic elements and all of their relevant properties
and configuration options are compatible with the physical site type of the
constraint.
Summary:
Symbols involved:
BUF symbol "XLXI_304/IBUF" (Output Signal = W_BUSB<14>)
TBUF symbol "XLXI_304/OBUFT" (Control Signal = notXRD)
PAD symbol "XD_14" (Pad Signal = XD_14)
Component type involved: IOB
Site Location involved: H18
Site Type involved: DIFFSI_NDT
ERROR:Pack:1107 - Pack was unable to combine the symbols listed below into a
single IOB component because the site type selected is not compatible. The
symbols have incompatible LOC attributes.
Mapping completed.
See MAP report file "TopLevelController3AN_map.mrp" for details.
Problem encountered during the packing phase.
Design Summary
------
Number of errors : 2
Number of warnings : 2
Process "Map" failed