1.PREFACE

1.1Orders are accepted in accordance with ArcelorMittal South Africa's General Conditions of Sale and prices VAT exclusive.

1.2All prices and transport tariffs (road or rail) are subject to a settlement discount of 2.5%, provided payment is made in accordance with ArcelorMittal South Africa’s General Conditions of Sale.

1.3All items are subject to “overage” and “underage”. Refer paragraph 3.2(page 2).

1.4Material addressed by this price list is sold at a price per metric ton (1000kg) on gross mass as recorded on the assized mass meter or weighbridge at the works.

1.5Unless otherwise stated, extras or deductions quoted in this price list are per metric ton and each extra or deduction is separate and explicit.

1.6Normal testing and inspection as outlined in the specifications are carried out. When additional inspection, testing or processing is required, extras will be charged.

1.7Prices and extras or deductions and transport tariffs are those ruling on date of confirmed delivery and are subject to change without prior notice.

1.8When placing orders, customers must always specify the end use and ensure that this is compatible with the ordered quality or specification. ArcelorMittal South Africa will then endeavour to deliver the material "fit for purpose". However, if the end use is in general terms such as "stock", or "general engineering", the product quality control will be in terms of the quality or specification only.

1.9After orders have been accepted and confirmed, they cannot be cancelled in whole or in part or altered in any manner whatsoever, except by special agreement with ArcelorMittal South Africa in writing. Should an order be modified, the order as amended, it will be re-priced.

1.10The publication of this price list does not place ArcelorMittal South Africa under any obligation to supply the quoted qualities and sizes at all times. Availability remains subject to confirmation and the stipulations in both the price list and relevant data sheets.

1.11Before processing material, customers must ensure that it meets their requirements. Non-compliance in this regard may invalidate a claim. ArcelorMittal South Africa does not prescribe any particular checking or testing methods. Visual checks, simple dimensional checks and reference to test certificates and/or orders should be performed beforehand.

2.PRICE INFORMATION (Definitions)

2.1ITEM

An item is a product of a single technical specification (i.e. a single quality, width, thickness, coil sizeand packaging, surface finish or condition, and any additional processing parameters required or requested.)

2.2ITEM EXTRAS

Item extras apply to the total number of full slab coils ordered per item for delivery in a given calendar month. Only identical items (full item description) will be combined for item extra determination (Best Tonnage Ordered “BTO’d”)

3.GENERAL INFORMATION

3.1MINIMUM ORDER QUANTITY

The minimum quantity per item ordered shall be in accordance with the following:

Standard items / Other items
One Full slab coil / Two full slab coils

Refer to Annexure 2 (page 9) for applicable full slab coil mass according to width and

Annexure 1 (page 7) for Standard items.

3.2OVERAGE/UNDERAGE

Please also refer to Annexure 3 (page 9) for tables.

The principle of delivering the proceeds of full slab coils is applicable in all cases.

3.2.1OVERAGE:

a)Ordered mass plus 10%, applicable for cases where less than 10 full slab-coils is ordered per item. This will be adjusted if a customer elects to have the underage adjusted as described in 3.2.2 c (for standard items and other items)

b)Ordered mass plus one full slab coil, for cases where 10 or more full slab-coils per standard item are ordered. For non-standard items an Overage of +10% will be allowed.

3.2.2UNDERAGE:

Standard items:

a)For cases where only one full slab-coil is ordered, the Underage allowed is ordered mass minus 25%.

b)For cases where more than one full slab-coil is ordered, the Underage allowed is ordered mass minus one maximum full slab-coil (nominal mass plus 10%).

c)However, in the case of standard items 2 to 4 slab-coil orders, customers may elect to have the Underage adjusted to 50% of a full-slab-coil below the ordered mass. In such a case the Overage will be adjusted to 60% of a full-slab-coil above the ordered mass. In this case the item extra for the whole order will be based on the increased order quantity, should the delivered mass exceed the originally ordered mass by more than a ½-slab coil.

Other items, not listed as standard items:

a)The Underage allowed is ordered mass minus one maximum full slab-coil (nominal coil mass plus 10%) when less than 10 full slab coils are ordered.

b)If 10 or more full slab coils are ordered, the Underage allowed will be minus 10%.

c)However, in the case of other available (non-standard) items 2 to 4 slab-coil orders, customers may elect to have the Underage adjusted to 60% of a full-slab-coil below the ordered mass. In such a case the Overage will be adjusted to 110% of a full-slab-coil above the ordered mass. In this case the item extra for the whole order will be based on the increased order quantity, should the delivered mass exceed the originally ordered mass by more than a ½-slab coil.

d)In cases where the underage applied results in less coils delivered than the original order, no penalty due to the reduced order quantity will be applied.

e)A replacement order for the proceeds of two slab-coils may be placed at an item extra equal to the original order, should the underage applied result in less material delivered than originally ordered.

3.3MASS OF COILS

3.3.1Mass of individual coils:

Orders for coils with a specified exact mass will not be accepted. Coils may be ordered to the nominal full coil mass as per ruling mass tables, or smaller split coils (half size).

Customers must indicate the maximum coil mass that can be handled to ensure the correct selection of available options.

3.3.1.1Full mass coils:

Defined as coils with a mass of at least 75% and a maximum of 110% of the specified nominal mass, as per ruling coil mass tables.

3.3.1.2Light mass coils:

Defined as coils with a mass less than full mass coils, but at least 60% of the nominal mass per ruling coil mass tables.

3.3.2Mass of all coils for the ordered item:

Despatch will take place as follows:

a)At least 80% of the ordered mass in full mass coils

b)Not more than 20% of the ordered mass in light mass coils

4.BASE PRICESR/ton (VAT exclusive)

HR incl. P&O: 2,0mm R 8 715

5.QUALITY EXTRAS

Specification / Quality
Code / Available Slab Widths
(mm) / Thickness
Range a)
(mm) / Quality Extra
R/t(VAT excl)
WHEELPRESS C1 / 574 000 / 1300 / P&O: 2,0 – 4,6
DRY: 2,0 – 14 / 365
WHEELPRESS C2 / 462 000 / 1300 / P&O: 2,2 – 4,0
DRY: 2,2 – 6 / 1000
WHEELPRESS C4 / 484 000 / 1300 / P&O: 2,0 – 4,6
DRY: 2,0 – 14 / 245
WHEELPRESS C500 b) / 444 001 / 960; 1000;1300Note D; 1450 / P&O: 3,0– 3,9
P&O: 4,0 – 5,0note C
DRY: 5,1 – 6,0 / 1150
WHEELRIMR2 / 458 000 / 1300; 1500 / P&O: 4,5 – 4,6
DRY: 4,5 – 10 / 245
WHEELRIMR3 / 459 000 / 1300; 1400; 1500 / P&O: 2,0 – 4,8
DRY: 2,0 – 6 / 180
MW01 / 457000 / 1300; 1400; 1500 / P&O: 2,0 – 4,8
DRY: 2,0 – 6 / 165
WHEELRIMSPH440 b) / 460 000 / 1400 / P&O: 2,0 – 4,0
DRY: 2,0 – 4,0 / 555
EN 10149 – 2 – S315MC (Low Si) / 942 000 / 1300; 1600 / P&O: 2,0 – 4,0
DRY: 2,0 – 10,0 / 665

Notes:

a)Thickness range available is dependent on type of steel and width-thickness ratio (refer Data Sheet A1.1).
Only theminimum thickness available in the narrowest available slab; and the maximum thickness areshown in the price list.

b)New Qualities initially on enquiry to determine dimensional capability, availability of slabs etc.

c)Only available from 960 mm slab

d)Slab width phasing out, strictly on Enquiry only

6.ITEM EXTRA TABLE

Item 1)
(Number of full slab coils) / Standard items 2) / Other items 3)
R/t (VAT exclusive) / R/t (VAT exclusive)
1 / 350 / Not Available
2 / 250 / 500
3 / 150 / 350
4 / 0 / 225

Notes:

1)Refer Annexure 2 Page 8 for applicable full slab coil mass according to width.

2)Refer Annexure 1 Page 7 for applicable Standard Items.

3)All other items not shown in Annexure 1.

7.WIDTH / THICKNESS EXTRAS

Thickness
(Available increments – 0,1mm) / Width (Mill Edge)
(Available increments 5mm)
R/t (VAT exclusive)
800 – 980mm / 985 – 1180mm / 1185 – 1590mm / 1595 – 1850mm
2,0 / 478 / 390 / 289 / Not available
2,2 / 456 / 368 / 267 / 328
2,3 / 447 / 359 / 258 / 320
2,4 / 442 / 355 / 254 / 315
2,5 / 438 / 350 / 250 / 311
2,8 / 429 / 342 / 241 / 302
2,9 / 425 / 337 / 236 / 298
3,0 / 421 / 333 / 232 / 293
3,2 / 416 / 328 / 228 / 289
3,5 / 412 / 324 / 223 / 285
3,8 / 407 / 320 / 219 / 280
4,0 / 403 / 315 / 214 / 276
4,5 / 390 / 302 / 201 / 263
5,0 / 390 / 302 / 201 / 263
6,0 / 390 / 302 / 201 / 263
8,0 / 416 / 328 / 228 / 289
10,0 / 442 / 355 / 254 / 315
12,0 / 473 / 385 / 285 / 346
14,0 / 504 / 416 / 315 / 377

Notes:

1)For gauges (thickness) not tabulated, but within the range 2,0mm to 14,0mm, the largerthicknessextra (above or below) that thickness will apply.

2) Gauges <2,0mm and >14mm POA (Price On Application)

8.PROCESSING EXTRAS

8.1PICKLING LINE WELDS

Pickle line welds are not acceptable

8.2PICKLING & OILING EXTRA

Thickness (mm) / Width
775mm – 1850mm
R/t (VAT exclusive)
2,0 4,8 / 381
>4,8  5,0 / 429

8.3SUPPLEMENTARY PICKLING EXTRAS

To be added to above (5.2) extra where applicable`R/ton (VAT excl)

8.3.1TENSILE STRENGTH 480 MPa but < 700MPa

Applicable to quality codes 462 000 (WPC2); 444 001 (WP C500)

For Thickness 4,0mm 65

For Thickness > 4,0mm416

8.3.2DIMENSIONS THICKER THAN INDICATED IN TABLE 2

  1. Thickness > 4,8mm for quality code 459 000 (WR R3) up to 5,0 mm maximum
    thickness, at 1250 mm maximum width285

b)Thickness > 4,6 for quality codes: 574 000 (C1); 484 000 (C4); 458 000 (R2)285

8.3.3 HIGH CARBON / ALLOYED STEELS (Carbon Equivalent CE 0,35)105

No quality codes currently applicable

8.3.4UN-OILED PICKLED COILS127

8.4TEMPER ROLLING (4,8 mm maximum) 100

8.5RESTRICTED THICKNESS TOLERANCE:135

(For closer thickness tolerance, but not less than 75% of specification)

8.6SIDE TRIM EXTRA:(only available for approved enquiry orders)236

8PROCESSING EXTRAS (Continued)

8.7CUT BACK TO THICKNESS 87

8.8MARKING to SANS 0202 (1361) 26

8.9WITNESSING OF MECHANICAL TESTS AND SURFACE INSPECTION

Witnessing mechanical test(0345) 61

Surface inspection(0577) 39

Surface inspection and marking out of test pieces(6029)122

Inspect: packaging(0466) 30

Inspect: packaging, weight & dimensions(0484) 39

8.10ENHANCED SURFACE

Recommended for all P&Owheel steels(Code 1012)100

Normal surface standard will apply on Hot Dry material

9.PACKAGING EXTRAS

Coil Mass
(t) / Packaging Code 1)
Non Protective / Advanced Protective
Un-pickled
Code 91 / Not Available
Pickled
Code 70 / Code 73
R/t (VAT exclusive)
Full Slab coil / 0 / 57
½ Slab coil / 171 / 228
1/3 Slab coil 2) / 285 / 342
¼ Slab coil 3) / Not Available / Not Available

Notes:

1)Refer to Packaging Specification for code descriptions and limitations.

2)1/3 size coils are only available on approved enquiries.

3)¼ size coils are not available

STANDARD ITEMS / ANNEXURE 1

1.WHEELRIM MW01(Code 457 000)

2,4 x 1265 mm / 1400mm slab / Mill edge, Pickled coils
3,0 x 1205 mm / 1300mm slab / Mill edge, Pickled coils
3,3 x 1270 mm / 1300mm slab / Mill edge, Pickled coils

2.WHEELRIM SPH440(Code 460 000)

2,3 x 1365 mm / 1400mm slab / Mill edge, Pickled coils
3,5 x 1325 mm / 1400mm slab / Mill edge, Pickled coils
3,8 x 1295 mm / 1400mm slab / Mill edge, Pickled coils

3.WHEELPRESS C500(Code 444 001)

3,8 x 1375 mm / 1450mm slab / Mill Edge, Pickled coils

*Refer to Annexure 5 for items changes

COIL MASS TABLE / ANNEXURE 2
SLAB WIDTH
(mm) / FINAL PRODUCT WIDTH
Mill edge
(HCW and HCPW) / Nominal
Full-coil mass
(ton)
960 # / (760 to 940 (HCW)) #
(775 to 940 (HCPW)) # / 17
1000 # / (945 to 980) # / 18
1100 # / (985 to 1080) # / 20
1200 / 1085 to 1180 / 22
1300 / 1185 to 1280 / 24
1400 / 1285 to 1380 / 25
1450 / 1340 to 1430 / 26
1500 / 1385 to 1480 / 27
1600 # / (1485 to 1590) # / 26
1700 # / (1595 to 1690) # / 27
1800 # / (1695 to 1790) # / 29
1870 # / (1795 to 1850 (HCW)) #
(1795 to 1830 (HCPW)) # / 31

Tolerance on coil mass: +10% -25% (Light Mass – 30%)

Notes:

Availability of Product Widths is subject to is subject Slab Width availability, width/thickness ratios andtype of steel, please refer to detail of availability in Data Sheet: Hot strip mill product dimensions, and theSlab Widths available as shown in Paragraph 2, Page 3 (Quality Extra Table)

# These slab widths, and corresponding Product widths, are only available for approved enquiry orders.

OVERAGE / UNDERAGE / ANNEXURE 3

DESPATCH TOLERANCE ON ORDER TONNAGE PER ITEM

The principle of a discrete Full Slab Coil as smallest sales unit applies

Number of Full Slab Coils * / STANDARD ITEM
%OVER / % UNDER / STANDARD ITEM OPTION2 (Code2010) %OVER / % UNDER
1 / +10/-25 / Not Applicable
2 / +10/-55 / +30/-25
3 / +10/-37 / +20/-17
4 / +10/-28 / +15/-13
5 / +10/-22 / Not Applicable
6 / +10/-18
7 / +10/-16
8 / +10/-14
9 / +10/-12
10 / +10/-11
>10 / +1 FSC / - 1,1 FSC*
Number of Full Slab Coils / NON-STANDARD ITEM
%OVER / % UNDER / NON-STANDARD ITEM OPTION2 (Code1020) %OVER / % UNDER
2 / +10/-55 / +55/-30
3 / +10/-37 / +36/-20
4 / +10/-28 / +27/-15
5 / +10/-22 / Not Applicable
6 / +10/-18
7 / +10/-16
8 / +10/-14
9 / +10/-12
10 / +10/-11
>10 / +10/-10
CHANGING STATUS ON ITEMS / ANNEXURE 4

2018-04-01Cancels and supersedes issue dated2018-01-01Page 1