1. PREFACE
1.1 Orders are accepted in accordance with ArcelorMittal South Africa's General Conditions of Sale and prices VAT exclusive.
1.2 All prices and transport tariffs (road or rail) are subject to a settlement discount of 2,5%, provided payment is made in accordance with ArcelorMittal South Africa’s General Conditions of Sale.
1.3 All items are subject to “overage” and “underage”. Refer paragraph 3.2( page 2).
1.4 Material addressed by this price list is sold at a price per metric ton (1000kg) on gross mass as recorded on the assized mass meter or weighbridge at the works.
1.5 Unless otherwise stated, extras or deductions quoted in this price list are per metric ton and each extra or deduction is separate and explicit.
1.6 Normal testing and inspection as outlined in the specifications are carried out. When additional inspection, testing or processing is required, extras will be charged.
1.7 Prices and extras or deductions and transport tariffs are those ruling on date of confirmed delivery and are subject to change without prior notice.
1.8 When placing orders, customers must always specify the end use and ensure that this is compatible with the ordered quality or specification. ArcelorMittal South Africa will then endeavour to deliver the material "fit for purpose". However, if the end use is in general terms such as "stock", or "general engineering", the product quality control will be in terms of the quality or specification only.
1.9 After orders have been accepted and confirmed, they cannot be cancelled in whole or in part or altered in any manner whatsoever, except by special agreement with ArcelorMittal South Africa in writing. Should an order be modified, the order as amended, it will be re-priced.
1.10 The publication of this price list does not place ArcelorMittal South Africa under any obligation to supply the quoted qualities and sizes at all times. Availability remains subject to confirmation and the stipulations in both the price list and relevant data sheets.
1.11 Before processing material, customers must ensure that it meets their requirements. Non-compliance in this regard may invalidate a claim. ArcelorMittal South Africa does not prescribe any particular checking or testing methods. Visual checks, simple dimensional checks and reference to test certificates and/or orders should be performed beforehand.
2. PRICE INFORMATION (Definitions)
2.1 ITEM
An item is a product of a single technical specification (i.e. a single quality, width, thickness, coil size and packaging, surface finish or condition, and any additional processing parameters required or requested.)
2.2 ITEM EXTRAS
Item extras apply to the total number of full slab coils ordered per item for delivery in a given calendar month. Only identical items (full item description) will be combined for item extra determination (Best Tonnage Ordered “BTO’d”)
3. GENERAL INFORMATION
3.1 MINIMUM ORDER QUANTITY
The minimum quantity per item ordered shall be in accordance with the following:
Standard items / Other itemsOne Full slab coil / Two full slab coils
Refer to Annexure 2 (page 10) for applicable full slab coil mass according to width and
Annexure 1 (page 8 to 9) for Standard items.
3.2 OVERAGE/UNDERAGE
Please also refer to Annexure 3, Page 11 for tables.
The principle of delivering the proceeds of full slab coils is applicable in all cases.
3.2.1 OVERAGE:
a) Ordered mass plus 10%, applicable for cases where less than 10 full slab-coils is ordered per item. This will be adjusted if a customer elects to have the underage adjusted as described in 3.2.2 c (for standard items and other items)
b) Ordered mass plus one full slab coil, for cases where 10 or more full slab-coils per standard item are ordered. For non-standard items an Overage of +10% will be allowed.
3.2.2 UNDERAGE:
Standard items:
a) For cases where only one full slab-coil is ordered, the Underage allowed is ordered mass minus 25%.
b) For cases where more than one full slab-coil is ordered, the Underage allowed is ordered mass minus one maximum full slab-coil (nominal mass plus 10%).
c) However, in the case of standard items 2 to 4 slab-coil orders, customers may elect to have the Underage adjusted to 50% of a full-slab-coil below the ordered mass. In such a case the Overage will be adjusted to 60% of a full-slab-coil above the ordered mass. In this case the item extra for the whole order will be based on the increased order quantity, should the delivered mass exceed the originally ordered mass by more than a ½-slab coil.
Other items, not listed as standard items:
a) The Underage allowed is ordered mass minus one maximum full slab-coil (nominal coil mass plus 10%) when less than 10 full slab coils are ordered.
b) If 10 or more full slab coils are ordered, the Underage allowed will be minus 10%.
c) However, in the case of other available (non-standard) items 2 to 4 slab-coil orders, customers may elect to have the Underage adjusted to 60% of a full-slab-coil below the ordered mass. In such a case the Overage will be adjusted to 110% of a full-slab-coil above the ordered mass. In this case the item extra for the whole order will be based on the increased order quantity, should the delivered mass exceed the originally ordered mass by more than a ½-slab coil.
d) In cases where the underage applied results in less coils delivered than the original order, no penalty due to the reduced order quantity will be applied.
e) A replacement order for the proceeds of two slab-coils may be placed at an item extra equal to the original order, should the underage applied result in less material delivered than originally ordered.
3.3 MASS OF COILS
3.3.1 Mass of individual coils:
Orders for coils with a specified exact mass will not be accepted. Coils may be ordered to the nominal full coil mass as per ruling mass tables, or smaller split coils (half size).
Customers must indicate the maximum coil mass that can be handled to ensure the correct selection of available options.
3.3.1.1 Full mass coils:
Defined as coils with a mass of at least 75% and a maximum of 110% of the specified nominal mass as per ruling coil mass tables.
3.3.1.2 Light mass coils:
Defined as coils with a mass less than full mass coils, but at least 70% of the nominal mass per ruling coil mass tables.
3.3.2 Mass of all coils for the ordered item:
Despatch will take place as follows:
a) At least 90% of the ordered mass in full mass coils
b) Not more than 10% of the ordered mass in light mass coils
3.4 OIL
ArcelorMittal South Africa will supply material with approved protective oil when specified, but cannot guarantee the thickness of the coating.
3.5 TELESCOPING
A degree of telescoping may occur on coils, but in this case the telescoping shall not exceed 30mm on a coil.
3.6 MARKING
The quality, width and thickness are marked on every coil. When a test and/or analysis certificate is required, the cast number will be shown on the coil.
4. BASE PRICE R/ton (VAT exclusive)
HOT ROLLED P & O: ³2,0mm thick R 8290
AUTOMOTIVE INDUSTRY ONLY
FOR GENERAL INDUSTRY REFER TO PRICE LIST 121 FOR BASE PRICE
5. QUALITY EXTRAS
Specification / QualityCode / Available Slab widths / Thickness Range a)
(mm) / R/ t
(VAT excl)
Note:
a) Thickness range available is dependant on type of steel and width-thickness ratio (refer Data Sheet A1.1) only the minimum thickness available in the narrowest available slab, and the maximum thickness is shown in the price list.
5.1 STRUCTURAL STEEL WITH IMPROVED FORMABILITY
SUPRAFORM HR 190 / 585 000 / 960; 1000; 1100; 1200; 1300; 1400; 1500; / 2.0 – 4.8 / 320SUPRAFORM HR 250 / 577 000 / 960; 1000; 1100; 1200; 1300; 1400; 1500; / 2.0 – 4.6 / 232
SUPRAFORM HR 290 (S0,010%) / 582 005 / 960; 1100; 1200;1300;1400;
1500; / 2.0 – 4.6 / 442
SUPRAFORM S315MC /
EN10149-2 S315MC / 556 000 / 1100; 1300 / 2.0 – 4.0 / 508
SUPRAFORM S355MC /
EN10149-2 S355MC / 557 000 / 960; 1100; 1300 / 2.0 – 4.0 / 574
SUPRAFORM S420MC /
EN10149-2 S420MC / 559 001 / 960; 1100; 1300 / 2.0– 4.0 / 828
JIS G3113 SAPH 400 (S,010 Low C) / 105 003 / 1300 / 2.0 – 4.0 / 420
JIS G3134 SPFH 590 (S,010) / 474 001 / 1100; 1300 / 2.3 – 4.0 / 908
Notes:
a) Other qualities in Pickled and Oiled Condition are available from Extra List 121 – General Industries
b) Use in conjunction with Data sheet A1.1 (Available width/thickness combinations).
c) Supraform TM range is being phased out and the TM specifications are on Enquiry only – Refer to Annexure 4 for equivalent specifications in Supraform MC range.
d) Minimum order quantity for all Supraform MC ranges will be 2 Full slab coils.
6. ITEM EXTRA TABLE
Item 1)(Number of full slab coils) / Standard items 2) / Other items 3)
R/t (VAT exclusive) / R/t (VAT exclusive)
1 / 228 / Not Available
2 / 0 / 482
Notes:
1) Please refer to Annexure 2 (Page 10) for applicable full slab coil mass according to width.
2) All Standard Items. For listing please refer to Annexure 1 (Page 8 to 9).
3) All other items not listed in Annexure 1.
7. WIDTH / THICKNESS EXTRAS
Thickness(Available increments – 0,1mm) / Width (Mill Edge)
(Available increments 5mm)
R/t (VAT exclusive)
800 – 980mm / 985 – 1180mm / 1185 – 1590mm / 1595 – 1830mm
2,0 / 478 / 390 / 289 / Not Available
2,2 / 456 / 368 / 267 / 328
2,3 / 447 / 359 / 258 / 320
2,4 / 442 / 355 / 254 / 315
2,5 / 438 / 350 / 250 / 311
2,8 / 429 / 342 / 241 / 302
2,9 / 425 / 337 / 236 / 298
3,0 / 421 / 333 / 232 / 293
3,2 / 416 / 328 / 228 / 289
3,5 / 412 / 324 / 223 / 285
3,8 / 407 / 320 / 219 / 280
4,0 / 403 / 315 / 214 / 276
4,5 & 4,8 / 390 / 302 / 201 / 263
Notes:
1) Pickled Steel is available ex Vanderbijlpark Steel only.
2) For gauges (thickness) not tabulated, but within the range 2,0 to 4,8mm, the larger thickness extra above or below that thickness will apply.
3) Availability of Product Widths and Thickness is subject to:
- Slab width availability and width-thickness ratio per type of steel
- Maximum pickled thickness for Group1 (soft) steels is 4,8mm
- Drawing and Forming qualities are not available in thickness less than 2,0mm
- Please check availability in data sheet or enquire.
8.1 PICKLING AND OILING EXTRAS
Thickness(mm) / All Available Widths
R/t (VAT exclusive)
2,0 £ 4,8 / 381
8.2 SUPPLEMENTARY PICKLING EXTRAS R/t (VAT exclusive)
To be added to above (5.1) extra where applicable.
8.2.1 TENSILE STRENGTH 400 Mpa but < 700Mpa
For Thickness 4,0mm 65
For Thickness > 4,0mm POA
Applicable to quality codes:
527 000 Supraform TM500
556 000 Supraform S315MC / EN 10149-2 S315MC
557 000 Supraform S355MC / EN 10149-2 S355MC
559 001 Supraform S420MC / EN 10149-2 S420MC
474 001 JIS G3134 SPFH 590 (S,010)
8.2.2 HIGH CARBON / ALLOYED STEELS (Carbon Equivalent CE > 0,35) 105
No quality codes currently applicable.
9. PROCESSING EXTRAS R/ton (VAT exclusive)
9.1 TEMPER ROLLING
4,8mm Maximum Thickness 100
9.2 RESTRICTED THICKNESS TOLERANCE
For closer tolerance, but not less than 75% of specification on price list 135
9.3 SIDE TRIM EXTRA 236
9.4 CUT BACK TO THICKNESS 87
9.5 MARKING
According to SANS 0202 (1361) 26
9.6 TEST PIECE CONDITION
Normalised 35
9.7 WITNESSING OF MECHANICAL TESTS AND SURFACE INSPECTION
Witnessing mechanical test (0345) 61
Surface inspection (0577) 39
Surface inspection and marking out of test pieces (6029) 122
Inspect packaging (0466) 30
Inspect packaging, weight & dimensions (0484) 39
10. PACKAGING EXTRAS
Coil Size / * Packaging CodeNon Protective
Code 70 / Advanced Protective
Code 73
R/t (VAT exclusive)
1/3 Slab Coil / On application only
½ Slab Coil / 0 / 57
Full slab Coil / -171 / -114
Note: * Please refer to Packaging Specification for code descriptions.
STANDARD ITEMS / ANNEXURE 1Thickness
(mm) / Product Width
(mm) / Applicable Slab Width / Product condition
1. SUPRAFORM HR 190 (code 585 000)
2,0 / 1225 / 1300 slab / Pickled, mill edge coils2,3 / * / 1050 / 1100 slab / Pickled, mill edge coils
2,3 / 1225 / 1300 slab / Pickled, mill edge coils
2,5 / 1225 / 1300 slab / Pickled, mill edge coils
2,6 / * / 1040 / 1100 slab / Pickled, mill edge coils
2,6 / 1225 / 1300 slab / Pickled, mill edge coils
2,6 / 1350 / 1400 slab / Pickled, mill edge coils
2,7 / 1225 / 1300 slab / Pickled, mill edge coils
2,9 / 1225 / 1300 slab / Pickled, mill edge coils
2,9 / 1350 / 1400 slab / Pickled, mill edge coils
3,0 / 1225 / 1300 slab / Pickled, mill edge coils
3,2 / 1225 / 1300 slab / Pickled, mill edge coils
3,5 / 1225 / 1300 slab / Pickled, mill edge coils
3,6 / 1225 / 1300 slab / Pickled, mill edge coils
3,8 / 1225 / 1300 slab / Pickled, mill edge coils
4,0 / 1225 / 1300 slab / Pickled, mill edge coils
4,5 / * / 1225 / 1300 slab / Pickled, mill edge coils
* Refer to Annexure 5 for item changes