Vicenza, Italy, 14-17 September 2016
three blank lines
TITLE (CAPITAL LETTERS, TIMES NEW ROMAN 14 PT BOLD, SINGLE-LINE SPACING, CENTERED-TEXT ALIGNMENT)
two blank lines
A. Author1*, B. C. Author2, C. Author1 (Times New Roman 12 pt, centered-text alignment)
one blank line
1Institute, Department, University/Company, Address (Times New Roman 11 pt, Italic, left-aligned)
2Institute, Department, University/Company, Address (Times New Roman 11 pt, Italic, left-aligned)
*e-mail address of the corresponding author (Times New Roman 11 pt, Italic, left-aligned)
one blank line
Keywords: a maximum of 4 keywords (Times New Roman 12 pt, single-line spacing, left-aligned text).
two blank lines
Abstract (Times New Roman 12 pt, bold, single-line spacing, left-aligned text)
Short abstract of approximately 5-10 lines identifying methods of analysis and significant results. Times New Roman, 12 pt, italic, single-line spacing, fully-justified text alignment.
two blank lines
1 Introduction (Times New Roman 12 pt, bold, single-line spacing left-aligned text)
1.1 Title of subsection (Times New Roman, 12 pt, italic, single-line spacing, left-aligned text)
The paper must be written in English using Times New Roman and 12 pt font size, with single line spacing and fully-justified text alignment, in a A4 paper with 2.5 cm margins. Pages must be numbered. The paper should be from 4 to 10 pages long.
Please leave two blank lines between paragraphs. Do not use indents.
The main text should include a proper introduction, description of the analysis, results and conclusions. Headings and subheadings for different sections must be clearly identified, according to the following scheme: 1, 1.1, 1.1.1, etc.
one blank line
Figure 1. Results of tensile tests on neat and nanomodified epoxy resin. (Times New Roman 10 pt, centered text alignment. Leave 6 pt space before the caption and a blank single line after it)
one blank line
All Figures and tables must be inserted in the text with centered alignment. They should also be properly quoted in the text. All data should be given in SI units.
one blank line
2 Materials and testing methods (Times New Roman 12 pt, bold, single-line spacing left-aligned text)
The caption of each table/figure must be below the respective table/figure. Leave a blank single line between the tables/figures and the text. The font within the tables should be Times New Roman, 11 pt. The labeling of figures should be in Times New Roman and legible (approximately 11 pt).
one blank line
Test n° / Stress [MPa] / N1 / 100 / 2000000
2 / 150 / 1000000
Table 1. Example of a caption (Times New Roman 10 pt, centered-text alignment. Leave 6 pt space before the caption and a blank single line after it).
one blank line
Equations should be numbered and properly referred to in the text. A blank single line should be left before and after each equation:
one blank line
(1)
one blank line
where E1 is the …
one blank line
References
The accuracy the references in the paper is under the full responsibility of the Author/Authors of the paper. All publications quoted in the text should be referred to by a number in square brackets, [1].
Full reference should be given in a list at the end of the paper according to the following format:
[1] Red A., Blue B.M. Title of the paper. Name of the Journal, Volume number, pp. xx-yy (year).
[2] Big M., Small M. Title of the Book. Publisher, City (year).
[3] Smart M.Z. Title of the Chapter in “Title of the Book”, edited by Big M.Q. and Small M.S. Publisher, City, Volume number, pp. xx-yy (year).
[4] Bad P.A., Good A. Title of the paper in “Proceeding of Name of the Conference or Symposium, Place of the conference, Country, (year).
[5] ASTM D 5528. Title of the standard (year).
2