This specification describes a high performance, articulated side walk tractor that shall support a variety of attachments. The versatility is required to allow operation in all four seasons of the year. Basic functions shall include snow removal from sidewalks, sanding/salting, sweeping, roadside mowing, and turf maintenance as described below.

Multi-Service VehicleGeneral Specifications / YES / NO / OTHER
Vehicle design to incorporate a high quality heavy duty-boxedfabricated .25” steel frame for longevity in high stress applications.
Frame must allow a minimum of 45 degrees articulation left or right. Front and rear frames must allow oscillation relative to each other up to +/- 15 degrees to provide improved traction and superior control of vehicle mounted implements/attachments.
Articulated steering to use twin, dual acting 2-inch steering rams with sensors for steering calibration.
Vehicle to provide all wheel drive via four hydrostatically driven wheel motors each with intelligent anti spin control, on four equally sized tires.
Standard equipment to include nitrogen charged accumulator as part of the front hitch hydraulic system to cushion load on hitch arms and provide improved comfort and handling during transport mode.
Vehicle and winter attachments shall all be made in the U.S.A
A 30,000 BTU heater and a 19,000 BTU air conditioning, R-134a. For clearance in urban areas, the air conditioner shall be integral to the cab, not roof mounted. Air conditioning shall NOT affect overall height of the vehicle.
Multi-Service Vehicle Engine Specifications / YES / NO / OTHER
Minimum Cummins QSB4.5, Four Cylinder, Tier 3, Turbo Charged and Charge Air Cooled.
110HP @ 2500 RPM, 115HP @ 2300 RPM
Bore/Stroke: 4.21/4.88 in. (107mm/124mm)
Displacement: 275 cu-in (4.5L)
Engine to come standard with factory installed grid heater cold starting aid.
Compression Ratio: 17.2 to 1
Peak Torque: 360 lb-ft @ 1500 RPM (488 N-m)
Fuel Consumption at max torque: .385 lbs/hp-hr
Engine shall be approved for operation on B20 biodiesel that conforms to American Society of Testing Materials standard ASTM D7467
Air cleaner maintenance and engine coolant level sensors to be networked to the vehicle control via a serial controller area network (CANBUS). Controller to provide an audible alarm and messages on operator’s console when filter maintenance is required.
Cummins engine ECM shall be networked to vehicle control network. All diagnostic and maintenance messages generated by engine to be read and displayed on the operator’s console.
Multi Service Vehicle Ground Drive Specifications / YES / NO / OTHER
Standard vehicle configuration to feature four (4) 10-ply “winter lugged” 10.5 x 80 – 18 tires mounted on heavy duty 10 bolt steel wheels.
Wheel motor based ground drive to incorporate four (4) Poclaintwo-speed hydrostatic wheel motors providing both transport mode and work mode. When operated in work mode the speed is to be 0 to 10 mph. Transport mode to allow vehicle speeds from 0 to 22mph with winter tires installed.
Eighteen gallon hydraulic reservoir to be shared by both the attachment hydraulic and hydrostatic ground drive systems.
Ability to customize hydrostatic deceleration on ground drive
Hydraulic system cooling to be provided by an engine mounted 20 inch suction fan to force air through rear mounted hydraulic cooler.
Sauer Danfoss piston type, electronic control, variable displacement pump capable of operating at 5800 psi to supply the wheel motors.
Dry type power take off clutch, electronic-over-hydraulic engagement, multi-plate design, 6-spline, 1 3/8” diameter. Standard front PTO to operate at 540 RPM @ 2160 engine RPM.
Steering system to be an articulated, two cylinder, load sense design. Articulated joints to feature greasable, spherical bearings with hardened bushings.
Vehicle to feature three braking systems:
Primary – Hydrostatic braking using all four wheel motors and hydrostatic ground drive.
Secondary – Dual caliper, automotive style disc brakes on front wheels.
Parking - Spring applied, hydraulically released mechanical parking brakes sealed in front wheel motors.
Parking brake to be automatically engaged/disengaged through the use of the foot pedal. Parking break status must be displayed on operator’s console.
An emergency brake release shall be plumbed into the hydraulic parking brake release circuit. This shall allow emergency release of the front axle parking brakes for towing or pushing at low speeds for short distances in the event of engine or other failure prohibiting the tractor from running. A manual pump with suitable check valves shall be provided to use hydraulic fluid from the vehicles main hydraulic system for brake release
Multi Service Vehicle Hydraulic System
and 3 Point Capacities / YES / NO / OTHER
Eaton radial piston-type, load sensing, flow compensated, hydraulic pump direct driven by the engine must supply up to 31gpm to auxiliary attachment drive circuit. Max operating pressure 3000 psi (206.8 bar).
Gear type or other fixed displacement pumps are not acceptable.
Any pump driven off of the vehicle’s front PTO is not acceptable, must be gear driven at the engine. Belt drive pumps not acceptable
Auxiliary hydraulic flow to be adjustable via the operator’s control console to allow hydraulic flow to match attachment requirements.
Front three point hitch configuration with two double acting lift cylinders and two quick coupling spring loaded hitch hooks. Front quick attach hitch linkage to accommodate category 1 and category 2 attachments.
All front attachment control hydraulics to be controlled by operator’s joystick. Six hydraulic quick couplers plus attachment hydraulic case drain to provide hydraulic connection for front mounted attachments shall be provided.
Hydraulic reservoir to supply both hydraulic ground drive and vehicle auxiliary hydraulics. Ground drive and auxiliary circuits to be supplied by three separate hydraulic system filters.
PTO access door required for access to PTO shaft hook up. Safety interlock must be provided to prevent engagement of ground drive, PTO and aux hydraulics if access door is open.
Shall be equipped with a weight transfer system to allow for the weight of the front attachment to be transferred to the front wheels to increase traction. Hitch weights are not allowed.
Multi Service Vehicle Operator’s Cab / YES / NO / OTHER
One man cab certified to comply with SAE Specification J1040C and ISO 3471. Three point seat belt system to comply with Seat Belt Anchorage Test SAE J2292.
Safety interlocks must be present on the seat, seat belt, and PTO access door. Ground drive, PTO, auxiliary hydraulic drive cannot be engaged if interlocks are lost. If safety interlocks are lost during operation, the vehicle must automatically and safely be brought to a halt and parking brake applied. Message center on vehicle control monitor shall indicate the nature of the fault.
Wide opening door shall be provided on left side for operator entry and exit. Both right and left side windows shall slide open and latch closed. Standard roof hatch to provide ventilation and to be used as an emergency exit.
Door shall be removable and replaceable without tools. Door must be equipped with a pressurized gas cylinder capable of holding the door in the full open position. It shall include greaseable hinge pins.
Cab to be carpeted or padded to provide sound and temperature insulation. Interior of cab to be carpeted with foam sound absorbing lining installed. Standard thermoformed headliner and trim panels also required to provide sound and temperature insulation. Sound level to be average of 73 dBA on “A” scale in cab at operating speeds between 2100-2320 engine RPM.
AM/FM Radio with weather band and two stereo speakers required. Additional terminal strip to connect external communication radios must be standard.
Steering column to telescope and tilt to accommodate multiple operating positions.
Steering column to have automotive style controls – directional light indication, hazard lights, two speed wipers with intermittent function, headlight and clearance light switch with high/low beams, three speed heater/air conditioner fan switch.
Operator’s seat to be air ride with adjustable head and arm rests. Switch in seat bottom must be activated to indicate operator presence before allowing engagement of ground drive, auxiliary hydraulic and PTO functions.
Heater to provide 30,000 BTU of heat transfer capacity with 662 cubic meter/hour of air circulation.
Cab to be pressurized and have replaceable fresh air filter with three speed ventilation fan.
Vehicle cab headliner to have six adjustable air ducts with louvered vents to allow air flow to be directed at operator for cooling or at window for defrost.
Air conditioning to be integrated, not roof mounted. It shall provide 19,000 BTU of cooling capacity minimum with 662 cubic meter/hour of air circulation capacity.
Vehicle to have two front headlights, two front clearance/directional lights, two red LED tail/signal/clearance lights, two clear LED back up lights, and SAE rated audible back up alarm.
Front windshield wiper to be pantograph design. Wiper and washer controls to be steering column mounted.
Washer fluid reservoir to be accessible and filled from operator’s cab.
Left and right side exterior breakaway rear view mirrors to be adjustable from inside cab through slide windows. Interior rear view mirror to be mounted in front upper right corner of cab and to be easily adjustable by operator.
Multi Service Vehicle Control/Electrical System / YES / NO / OTHER
Three phase 95 amp, 12 volt alternator with 1125 CCA battery minimum with external battery terminals for ease of access. Standard battery disconnect.
All vehicle controls to be electric over hydraulic type. Vehicle and engine ECM to be networked and controlled by CAN (Controller Area Network) serial bus technology.
Main operator’s console in cab to incorporate the Plus+1® 9 inch liquid crystal, 14 button, color display screen.
Vehicle system (troubleshooting) and engine diagnostics to be displayed on the Plus+1® screen.
Plus+1® screen displays to be easily viewed in direct sunlight and backlit for night viewing. Screen brightness must be adjustable by the user.
Operator display to include 14 mechanically sealed pushbuttons to allow access to the vehicle menus.
Main operator console shall include joystick diagnostics to verify operation or fault in joystick.
An 18 function joystick must be programmable by the user.
Vehicle shall be equipped with standard cruise control.
Wire harness shall have plug and play types with labeled ends
Multi Service Vehicle Dimensions and Capacities / YES / NO / OTHER
Fuel tank capacity to be 21 gallons (79.49 liters) with remote fill. Fitted with 25 micron fuel filter.
Overall vehicle length to be 157 inches (3988 mm).
Maximum overall vehicle cab width to be 49.5 inches (1258 mm) with 10.5 x 80 – 18 winter tires.
Maximum overall width at the tires to be 49.5 inches (1258 mm) with 10.5 x 80 - 18 winter tires.
Cab height to be 82.6 inches max (2098 mm) with winter tires, exclusive of removable beacons.
Ground clearance to be 13.4.25 inches (340 mm) with winter tires.
Inside turning radius to be 80 inches (2032 mm) at angle of 45 degrees
Outside turning radius to be 129.5 inches (3289 mm) at angle of 45 degrees
Wheel base to be 83 inches (2108 mm).
Curb weight to be 6620 lbs. (3002 kg).
12,000 lbs gross vehicle weight rating at the hubs (5436 kg)
Maximum allowable individual front axle load or rear axle load shall be8,000 lbs (3625 kg), at the ground.
Multi Service Vehicle Warranty / YES / NO / OTHER
Base tractor shall be covered by a one year warranty. Bidder shall provide a warranty statement with bid.
Engine shall be covered by a two-year warranty. Bidder shall provide a warranty statement with bid.
Hydrostatic ground drive wheel motors to be covered by a two-year warranty. Bidder shall provide a warranty statement with bid.

OPTIONS AVAILABLE ON MSV

OPTIONS AVAILABLE ON MSV
One spare 10-ply “winter lugged” 10.5 x 80 – 18 tire, mounted on heavy duty 10 bolt steel wheel to match winter tires installed on vehicle, shipped loose, not to be carried on the vehicle.
Vehicle to be configured with feature four (4) 10-ply “winter lugged” 10.5 x 80 – 18 tires mounted on heavy duty 10 bolt steel wheels.
Vehicle shall be equipped with four (4) 10-plyradial winter tires Load Range E, Avalanche Extreme, 275/70R18 non directional tires.
One spare 10-plyradial winter tire load range E, Avalanche Extreme, 275/70R18 non directional tire shall be provided mounted on wheel for a spare, not to be carried on the vehicle.
A hydraulic control circuit shall be provided from the auxiliary hydraulic pump to a location at the rear of the vehicle. Flow shall be controlled by means of the operator’s joystick control in the cab to provide for the function of drop spreader, dump box lift/lower, or other rear mount attachment. Control of the hydraulics to be by means of cab mounted joystick.
In addition to the standard winter tires mounted on the vehicle, a complete set of Four (4) Summer 10-ply turf tires 33/16LL500, mounted on rims, shall be provided for best performance of the unit in summer mowing operations.
One spare summer 10-ply turf tire 33/16LL500, mounted on rim, shall be provided loose, not to be carried on the vehicle.
A 110 volt engine block heater shall be provided to assist in cold start situations. Kit shall be complete with electrical cord routed for convenient shop access.
A 110 volt winter start package is required, providing overnight heat of battery, hydraulic tank and fuel system. Kit shall be complete with electrical cord routed for convenient shop access.
A filter kit, including one filter element for each on board filter. This will allow purchaser to refresh all vehicle filters after initial vehicle break-in.
An 5lb fire extinguisher shall be included
Rear work lights shall be installed to optimize viewing of rear attachments

Page 1