Section 124813 - Entrance Floor Mats and Frames

Copyright 2015 AIA MasterSpec Premium 06/15

PRODUCT MASTERSPEC LICENSED BY ARCOM TO NYSTROM, INC.

Copyright 2015 by The American Institute of Architects (AIA)

Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA

This Product MasterSpec Section is licensed by ARCOM to Nystrom, Inc. ("Licensee").

This Product MasterSpec Section modifies the original MasterSpec text and does not include the full content of the original MasterSpec Section.

Revisions made to the original MasterSpec text are made solely by the Licensee and are not endorsed by, or representative of the opinions of, ARCOM or The American Institute of Architects (AIA). Neither AIA nor ARCOM are liable in any way for such revisions or for the use of this Product MasterSpec Section by any end user. A qualified design professional should review and edit the document to suit project requirements.

For more information, contact Nystrom, Inc., 9300 73rd Avenue North, Minneapolis, MN 55428; Phone: (800) 547-2635; Website: www.Nystrom.com.

For information about MasterSpec, contact ARCOM at (800) 424-5080 or visit www.MasterSpec.com.

SECTION 124813 - ENTRANCE FLOOR MATS AND FRAMES

TIPS:

To view non-printing Editor's Notes that provide guidance for editing, click on MasterWorks/Single-File Formatting/Toggle/Editor's Notes.

To read detailed research, technical information about products and materials, and coordination checklists, click on MasterWorks/Supporting Information.

Revise this Section by deleting and inserting text to meet Project-specific requirements.

This Section uses the term "Architect." Change this term to match that used to identify the design professional as defined in the General and Supplementary Conditions.

Verify that Section titles referenced in this Section are correct for this Project's Specifications; Section titles may have changed.

PART 1 - GENERAL

1.1  RELATED DOCUMENTS

Retain or delete this article in all Sections of Project Manual.

  1. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division01 Specification Sections, apply to this Section.

1.2  SUMMARY

  1. Section Includes:
  2. Entrance floor mat and frame assemblies.
  3. Related Requirements:

Retain subparagraph below to cross-reference requirements Contractor might expect to find in this Section but are specified in other Sections.

  1. Section124816 "Entrance Floor Grilles" for rigid floor grilles and frames.

1.3  COORDINATION

  1. Coordinate size and location of recesses in concrete to receive floor mats and frames.

1.4  ACTION SUBMITTALS

  1. Product Data: For each type of product.
  2. Include construction details, material descriptions, dimensions of individual components and profiles, and finishes for floor mats and frames.
  3. Shop Drawings:

Revise four subparagraphs below to suit Project.

  1. Items penetrating floor mats and frames, including door control devices.
  2. Divisions between mat sections.
  3. Perimeter floor [moldings] [frames].
  4. Custom Graphics: Scale drawing indicating colors.

Retain "Samples" Paragraph below for single-stage Samples, with a subordinate list if applicable.

  1. Samples: For the following products, in manufacturer's standard sizes:
  2. Entrance Floor Mat: Assembled sections of floor mat.
  3. Tread Insert: Sample of each type and color.
  4. Frame Members: Sample of each type and color.

1.5  CLOSEOUT SUBMITTALS

  1. Maintenance Data: For floor mats and frames to include in maintenance manuals.

1.6  MAINTENANCE MATERIAL SUBMITTALS

  1. Furnish extra materials that match products installed and that are packaged with protective covering for storage and identified with labels describing contents.

PART 2 - PRODUCTS

Manufacturers and products listed in SpecAgent and MasterWorks Paragraph Builder are neither recommended nor endorsed by the AIA or ARCOM. Before inserting names, verify that manufacturers and products listed there comply with requirements retained or revised in descriptions and are both available and suitable for the intended applications. For definitions of terms and requirements for Contractor's product selection, see Section016000 "Product Requirements."

2.1  ENTRANCE FLOOR MATS AND FRAMES, GENERAL

  1. Accessibility Standard: Comply with applicable provisions in the DOJ's "2010 ADA Standards for Accessible Design" and ICCA117.1.

2.2  ROLL-UP RAIL MATS

Retain one or more of four "Roll-up Mat" Paragraphs below to meet Project requirements.

  1. Roll-up, LDPE-Hinged Mats: Extruded-aluminum tread rails 2 inches (50 mm) on-center by 3/8-inch (9.5-mm) thick, sitting on continuous vinyl cushions.
  2. Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; QuietFLEX® or a comparable product by one of the following:
  3. Babcock-Davis.
  4. C/S Group.
  5. Insert manufacturer's name>.

Retain seven subparagraphs below if required. Revise those retained to suit Project.

  1. Tread Inserts:

Retain one or more of the following nine subparagraphs if retaining "Tread Inserts" Subparagraph above. Multiple inserts may be selected for alternating treads. Two treads may be selected; for example, Premium Carpet for absorbing and Vinyl for scraping.

  1. Premium Carpet with 3700 denier, solution-dyed, woven nylon fibers; and shall include a minimum of 100, 10 mil monofilament fibers per square inch. Each carpet fiber and monofilament shall be fusion-bonded to a rigid, two-ply backing to prevent fraying and supplied in continuous, spliced-free lengths. Fibers shall be treated with anti-stain and anti-static additives.
  2. Rugged Scrub crimped, solution-dyed, 600 denier polypropylene fibers tufted into a woven double backing and mechanically secured to tread rails.
  3. Brush: Brush made with rigid nylon bristles, 9 tufts per inch, each tuft containing 80 bristles.
  4. Vinyl: Ribbed-design-surface, resilient vinyl.
  5. Serrated Aluminum: Plain serrated aluminum treads.
  6. Recycled Rubber: SC of 90 manufactured with recycled rubber and EPDM backing.

1)  Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; Ecotread.

  1. Ribbed Rubber: TPV, dual-durameter rubber insert with convex and continuous serrations.
  2. Abrasive Insert: Mineral abrasive particles bonded to vinyl.
  3. Poured Abrasive: Serrated aluminum surface covered with aluminum-oxide or silicon-carbide grit in epoxy matrix.
  4. Colors, Textures, and Patterns of Inserts: [As indicated by manufacturer's designations] [Match Architect's sample] [As selected by Architect from full range of industry colors].
  5. Rail Color: [Mill finish] [Clear] [Light bronze] [Medium bronze] [Dark bronze] [Black].
  6. Hinges: LDPE.
  7. Structural Performance: Wheel load of 300 lb (136 kg) per wheel.
  8. Mat Size: [As indicated] <Insert size>.
  9. Frame:

Retain "Recessed Frames" or "Surface-Mounted Frames" Subparagraphs below.

  1. Recessed Frames:

Retain "LBM" or "LBC" Subparagraphs below.

1)  LBM: Level-bed, mechanically fastened 6063-T5 aluminum frame.

2)  LBC: Level-bed, cast-in-place 6063-T5 aluminum frame.

3)  Color: [Mill finish] [Clear] [Light bronze] [Medium bronze] [Dark bronze] [Black] [Match Architect's sample] [As selected by Architect from full range of industry colors and color densities].

  1. Surface-Mounted Frames:

Retain one of two "Tapered Ramp Frames" subparagraphs below.

1)  Tapered Ramp Frames: SAM; Mechanically fastened, tapered 6063-T5 aluminum frame with mitered corners.

2)  Tapered Ramp Frames: SV; Tapered vinyl frame.

  1. Roll-up, Aluminum Hinged Mats: Extruded-aluminum tread rails 2 inches (50 mm) on-center by 3/8-inch (9.5-mm) thick, sitting on continuous vinyl cushions.
  2. Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; MATdesign® or a comparable product by one of the following:
  3. Babcock-Davis.
  4. C/S Group.
  5. Insert manufacturer's name>.

Retain seven subparagraphs below if required. Revise those retained to suit Project.

  1. Tread Inserts:

Retain one or more of the following seven subparagraphs if retaining "Tread Inserts" Subparagraph above. Multiple inserts may be selected for alternating treads. Two treads may be selected; for example, Premium Carpet for absorbing and Vinyl for scraping.

  1. Premium Carpet with 3700 denier, solution-dyed, woven nylon fibers; and shall include a minimum of 100, 10 mil monofilament fibers per square inch. Each carpet fiber and monofilament shall be fusion-bonded to a rigid, two-ply backing to prevent fraying and supplied in continuous, spliced-free lengths. Fibers shall be treated with anti-stain and anti-static additives.
  2. Rugged Scrub crimped, solution-dyed, 600 denier polypropylene fibers tufted into a woven double backing and mechanically secured to tread rails.
  3. Brush: Brush made with rigid nylon bristles, 9 tufts per inch, each tuft containing 80 bristles.
  4. Vinyl: Ribbed-design-surface, resilient vinyl.
  5. Recycled Rubber: SC of 90 manufactured with recycled rubber and EPDM backing.

1)  Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; Ecotread.

  1. Ribbed Rubber: TPV, dual-durameter rubber insert with convex and continuous serrations.
  2. Abrasive Insert: Mineral abrasive particles bonded to vinyl.
  3. Colors, Textures, and Patterns of Inserts: [As indicated by manufacturer's designations] [Match Architect's sample] [As selected by Architect from full range of industry colors].
  4. Rail Color: [Mill finish] [Clear] [Light bronze] [Medium bronze] [Dark bronze] [Black].
  5. Hinges: Aluminum.
  6. Structural Performance: Wheel load of 350 lb (159 kg) per wheel.
  7. Mat Size: [As indicated] <Insert size>.
  8. Frame:

Retain "Recessed Frames" or "Surface-Mounted Frames" Subparagraphs below.

  1. Recessed Frames:

Retain "LBM" or "LBC" Subparagraphs below.

1)  LBM: Level-bed, mechanically fastened 6063-T5 aluminum frame.

2)  LBC: Level-bed, cast-in-place 6063-T5 aluminum frame.

3)  Color: [Mill finish] [Clear] [Light bronze] [Medium bronze] [Dark bronze] [Black] [Match Architect's sample] [As selected by Architect from full range of industry colors and color densities].

  1. Surface-Mounted Frames:

1)  Tapered Ramp Frames: SAM; Mechanically fastened, tapered 6063-T5 aluminum frame with mitered corners.

  1. Roll-up, LDPE-Hinged Mats: Vinyl-acrylic tread rails 1-7/8 inches (48 mm) on-center by 3/8-inch (9.5-mm) thick, with slotted or perforated hinges.
  2. Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; MATrac or a comparable product by one of the following:
  3. Babcock-Davis.
  4. C/S Group.
  5. Insert manufacturer's name>.

Retain seven subparagraphs below if required. Revise those retained to suit Project.

  1. Tread Inserts:

Retain one or more of the following seven subparagraphs if retaining "Tread Inserts" Subparagraph above. Multiple inserts may be selected for alternating treads. Two treads may be selected; for example, Premium Carpet for absorbing and Vinyl for scraping.

  1. Premium Carpet with 3700 denier, solution-dyed, woven nylon fibers; and shall include a minimum of 100, 10 mil monofilament fibers per square inch. Each carpet fiber and monofilament shall be fusion-bonded to a rigid, two-ply backing to prevent fraying and supplied in continuous, spliced-free lengths. Fibers shall be treated with anti-stain and anti-static additives.
  2. Rugged scrub crimped, solution-dyed, 600 denier polypropylene fibers tufted into a woven double backing and mechanically secured to tread rails.
  3. Brush: Brush made with rigid nylon bristles, 9 tufts per inch, each tuft containing 80 bristles.
  4. Vinyl: Ribbed-design-surface, resilient vinyl.
  5. Recycled Rubber: SC of 90 manufactured with recycled rubber and EPDM backing.

1)  Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; Ecotread.

  1. Ribbed Rubber: TPV, dual-durameter rubber insert with convex and continuous serrations.
  2. Abrasive Insert: Mineral abrasive particles bonded to vinyl.
  3. Colors, Textures, and Patterns of Inserts: [As indicated by manufacturer's designations] [Match Architect's sample] [As selected by Architect from full range of industry colors].
  4. Rail Color: Black.
  5. Hinges: LDPE.
  6. Structural Performance: Wheel load of 350 lb (159 kg) per wheel.
  7. Mat Size: [As indicated] <Insert size>.
  8. Frame:

Retain "Recessed Frames" or "Surface-Mounted Frames" Subparagraphs below.

  1. Recessed Frames:

Retain "LBM" or "LBC" Subparagraphs below.

1)  LBM: Level-bed, mechanically fastened 6063-T5 aluminum frame.

2)  LBC: Level-bed, cast-in-place 6063-T5 aluminum frame.

3)  Color: [Mill finish] [Clear] [Light bronze] [Medium bronze] [Dark bronze] [Black] [Match Architect's sample] [As selected by Architect from full range of industry colors and color densities].

  1. Surface-Mounted Frames:

Retain one of two "Tapered Ramp Frames" subparagraphs below.

1)  Tapered Ramp Frames: SAM; Mechanically fastened, tapered 6063-T5 aluminum frame with mitered corners.

2)  Tapered Ramp Frames: SV; Tapered vinyl frame.

D.  Roll-up, Vinyl Mat: Flexible, open weave, vinyl mat with carpet inlays. Sections are 0.25-inch- (6.4-mm-) square ribs with 0.230 by 0.312 inch (5.8 by 7.9 mm) openings over 0.25 inch (6.4 mm) half-rounds, 1.25 inch (31.8 mm) apart. Carpet inserts are 1.157 inch (29.4 mm) wide. The mat is secured with a patented retainer system.

  1. Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; MAXTread™ or a comparable product by one of the following:
  2. Babcock-Davis.
  3. C/S Group.
  4. Insert manufacturer's name>.

Retain seven subparagraphs below if required. Revise those retained to suit Project.

  1. Tread Inserts:
  2. Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc. TuffScrub.
  3. Carpet Tread: Crimped, solution-dyed, 2750 denier polypropylene fibers tufted into a woven double backing and glued tread rails. Carpet weight shall be 26 oz./sq.yd. (881 g/sq.m).
  4. Color: [Charcoal] [Walnut].
  5. Construction: Injection-molded PVC
  6. Rail Color: [Black] [Brown] [Gray].
  7. Structural Performance: Wheel load of 1200 lb (544 kg) per wheel.
  8. Mat Size: [As indicated] <Insert size>.
  9. Frames:
  10. Aluminum Frame: Extruded 6063-T5 aluminum alloy.
  11. Frame Finish: [Clear] [Color anodized].
  12. Construction: Frames shall be shipped in 72-inch (1829-mm) sections to each jobsite.
  13. Mounting:

1)  LTR: Aluminum mechanically attached, Level Bed Transition frame, 0.4 to 0.6 inches (10.6 to 15.2 mm) transition profile; 1 inch (25.4 mm) overall depth.

2)  LTO: Aluminum mechanically attached, Level Bed Transition frame with overhang, 0.4 to 0.6 inches (10.6 to 15.2 mm) transition profile; 1 inch (25.4 mm) overall depth.

3)  LCH: Aluminum mechanically attached, Level Bed Channel frame, 1/2-inch (12.7-mm) channel profile; 3/4-inch (19-mm) overall depth.

4)  SAM: Surface mounted, mechanically attached frame. 2.3 inches (59 mm) profile; 0.625 inch (15.9 mm) overall depth; mill finish.

5)  SV: Surface mounted, vinyl attached frame, shall have an overall depth of 1/2-inch- (12.7-mm-) deep with a 3-inch (76.2-mm) profile; mill finish.

E.  Roll-up, Vinyl Mat: Flexible, open weave, vinyl mat. Sections are a nominal 0.25-inch- (6.4-mm-) square ribs with nominal 0.230 by 0.312 inch (5.8 by 7.9 mm) openings over 0.25 inch (6.4 mm) half rounds 1.25 inch (31.8 mm) apart. Secure mat with manufacturer patented retainer system.

  1. Basis-of-Design Product: Subject to compliance with requirements, provide Nystrom, Inc.; MAXgrid or a comparable product by one of the following:
  2. Babcock-Davis.
  3. C/S Group.
  4. Insert manufacturer's name>.
  5. Construction: Injection molded PVC.
  6. Rail Color: [Black] [Gray] [Brown].
  7. Structural Performance: Wheel load of 1200 lb (544 kg) per wheel.
  8. Mat Size: [As indicated] <Insert size>.
  9. Frames:
  10. Aluminum Frame: Extruded 6063-T5 aluminum alloy
  11. Frame Finish: [Clear] [Color anodized].
  12. Construction: Frames shall be shipped in 72-inch (1829-mm) sections to each jobsite.
  13. Mounting:

1)  LTR: Aluminum mechanically attached, Level Bed Transition frame, 0.4 to 0.6 inch (10.6 to 15.2 mm) transition profile; 1-inch (25.4-mm) overall depth.

Top View