Lot # 1 - Used 30” Stanford 142 Salvage Rewinder / Doctor Machine
Used 30” Stanford Salvage Rewinder Model 142 equipped with 48" maximum diameter shafted unwind with disc brake, edge guide, skewing, dancer roll tension control, adjustable bow bar, air operated rider roll, one (1) shear knife holder, 24" maximum diameter cantilevered rewind with 3" diameter air shaft, 5 HP drive, overhead hoist at unwind with structure.Mfr date: 1974. Serial Number: 11743866 (Located in Scotia, NY) (Rig/Load Fee $800)
Lot # 2 – Used 20” Rotoflex SW-2000 Slitter Rewinder
Used 20” Rotoflex Slitter Rewinder Model SW-2000 equipped with a 45" maximum diameter roll lift shafted unwind (Montalvo brake, dancer tension control), E+L offset pivot edge guide and controls, splice boards before slitting station and at rewind, Rotary shear slitting section (no male knives), score slitting section (no male knives) web inspection area above rewind, and 45" maximum diameter roll lowering shafted rewind, 2-motor drive, 5 HP drive motor with Montalvo clutch. Mfr. Date: 1990, Serial Number: SW-266-850919 (Located in Scotia, NY) (Rig/Load Fee $350)
Lot # 3 – Used 48” Dusenbery 820 BJ Simplex Slitter
Used Dusenbery 820 BJ simplex slitter equipped with 40" maximum diameter unwind with 8" Wichita Magnum disc brake, two (2) 3" air shafts, one (1) 2" solid shaft,Fife edge guide with Fife P25 power unit, bowed roll, driven pull roll section, razor edge trimming, center surface rewind with hydraulic center assist, 5 HP hydraulic power unit, 5 HP DC main drive. (Located in Scotia, NY) (Rig/Load Fee $400)
Lot # 4 – Used 54” Kidder CW Simplex Slitter
Used 54” Kidder Simplex Slitter Model CW, equipped 50" maximum diameter shafted unwind with roll lift, water-cooled brake, mechanical edge guide, shear slitting (17 female knives, 1 male knife), 40" maximum diameter rewind with roll lowering, trim chopper, trim blower, GE 20 HP motor with MG set. (Located in Scotia, NY) (Rig/Load Fee $250)
Lot #5 – Used 24” Dusenbery 618 AJ Duplex Center Slitter
Used 24” Dusenbery duplex center slitter Model 618 AJ equipped with 30" maximum diameter unwind with 3" air shaft and 4" disc brake, manual edge guide, 20 pneumatic score knives, dual manifold for 0.5" slit widths, knurled rolls for PS materials, 8” diameter rewinds with 3" leaf-type air shafts at rewind, 3 HP Drive. Serial Number: 48877 (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 6 – Used 62” Dusenbery 635 Duplex Center Slitter
Used 62” Dusenbery duplex center slitter Model 635 equipped with a Model 824 40" maximum diameter single position unwind with 9" Montalvo disc brake, edge guide, rotary shear slitting with pneumatic female knife shaft, 24" maximum diameter duplex differential center wind with Montalvo clutches at each rewind position, 3" diameter lug-type air shafts, Veeder Root Multi-Shift counter, 7-1/2 HP DC drive. Serial Number: 51557 (Located in Scotia, NY) (Rig/Load Fee $150)
Lot # 7 –Used 1300mm Titan SR5 Duplex Center Slitter
Used 1300mm(51”)Titan duplex center slitter Model SR5 equipped with 1000mm(40”) maximum diameter shafted integral unwind with roll lift, auto tension control, edge guide, shear and razor slitting, 610mm(24”) maximum diameter cantilevered rewinds with 3” Quicklocks, 3-motor DC drive.Mfr date: 1989. (Located in Scotia, NY) (Rig/Load Fee $250)
Lot # 8 – Used 36” Dusenbery 809 Duplex Turret Center Slitter
Used 36” Dusenbery duplex turret center slitter Model 809 equipped with 30" maximum diameter turret unwind, vacuum splice board, web cleaning section, shear slitting knife box, vacuum pull roll, individual air operated rider roll assemblies for 1" slits, 12" maximum diameter dual turret rewinds, DC drive system with Hitachi PLC. Designed for precision slitting of magnetic tape. (Located in Scotia, NY) (Rig/Load Fee $875)
Lot # 9 – Used 36” Dusenbery 809 Duplex Turret Center Slitter
Used 36” Dusenbery duplex turret center slitter Model 809 equipped with 30" maximum diameter turret unwind, vacuum splice board, web cleaning section, shear slitting knife box, vacuum pull roll, individual air operated rider roll assemblies for 1" slits, 12" maximum diameter dual turret rewinds, DC drive system with Hitachi PLC. Designed for precision slitting of magnetic tape. (Located in Scotia, NY) (Rig/Load Fee $875)
Lot # 10 – Used 39” Dusenbery 636 TTR Duplex Turret Center Slitter
Used 39” Dusenbery duplex turret center slitter model 636 TTR equipped with 30" maximum diameter unwind with cantilevered 6" diameter lug type air shaft & disc brake; leader table with pneumatic clamping, transducer tension roll; 6" maximum diameter duplex turret center rewind with 1/2" & 1" diameter rewind shafts; adjustable bowed roll; razor in grooved roll slitting with five (5) grooved rolls; driven pull roll with nip roll; Lenze 2 motor DC drive system; Mitsubushi PLC MELSEC FX-48MR-ES. Serial Number: 81527 (Located in Scotia, NY) (Rig/Load Fee $675)
Lot # 11 – Used 42” Cameron 608 Duplex Center Surface Slitter
Used 42” Cameron duplex center surface slitter Model 608 equipped with 36" maximum diameter single position unwind, edge guiding with Fife P25 power unit, razor slitting with shear in storage, 24" maximum diameter duplex center surface wind for differential winding with four (4) 3" differential shafts, clutches at each rewind position. Rebuilt in 1997 with timing belt drives. (Located in Scotia, NY) (Rig/Load Fee $450)
Lot # 12 – Used 62” Elite Cameron CS550 Duplex Center Surface Slitter
Used 62” Elite Cameron CS550 Duplex Center Surface Slitter equipped with a 40" maximum diameter shaftless floor pickup unwind (3" & 6" core chucks, Montalvo brakes, diameter sensor, Fife edge guide, skewing roll, peel off roll, dancer roll, sound-deadening enclosure, closed-loop automatic tension control system, anti-static control, splicing roll), scrap rewind, slat spreader roll, slotted and knurled driven pull roll, razor-in-air and score slitting (0.5" minimum slit width, 20 score knives), 20" maximum diameter duplex center surface rewind (minimum gap capable, cantilevered, 3" leaf type air shafts, automatic tension control, anti-static control), tabbing unit, Allen-Bradley Panel View 1000 touch screen, Allen-Bradley PLC, Eurotherm 690+ AC drives, four (4) Marathon Black Max AC motors.Mfr Date: 2002. Serial Number: 51283-18-1-1-1-12-01 (This item is uninstalled and currently stored in a climate controlled warehouse.) (Located in Scotia, NY) (Rig/Load Fee $1,500)
Lot # 13 – Used 51” Alan Duffy Inspection Rewinder
Used 51” Alan Duffy Inspection Rewinder equipped with 32" maximum diameter integral unwind with disc brake and safety chucks; edge guide; vacuum splice board with pneumatic clamping; inspection area with light; S-wrap pull roll; 20" maximum diameter single position rewind with air operated rider roll & taper tension; 3" diameter lug-type rewind shaft; three (3) 1" steel rewind shafts, 2-motor DC drive system. Serial Number: 931556 (Located in Scotia, NY) (Rig/Load Fee $325)
Lot # 14 – Used 63” Hsia Yan FD Single Knife Cutter (Baloney Slicer)
Hsia Yan Single Knife Cutter (Baloney Slicer), automatic, and equipped with 3" dual mandrels for 6" maximum diameter rolls, 10" knife, and a 2 HP motor. 220/380VAC/3Ph/50/60Hz.Mfr Date: 1990. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 15 – Used 4” Leesona 955 Traverse Winder
Used 4” Leesona traverse winder, model 955, two position winder equipped with 1.5 HP motor. 127/220V, 60Hz, 3 Phase. Serial Number: 4920-21 (Located in Scotia, NY) (Rig/Load Fee $150)
Lot # 16 – Used 4” Leesona 955 Traverse Winder
Used 4” Leesona traverse winder, model 955, two position winder equipped with 1.5 HP motor. 127/220V, 60Hz, 3 Phase. Serial Number: 4916-17 (Located in Scotia, NY) (Rig/Load Fee $150)
Lot # 17 – Used 4” Leesona 955 Traverse Winder
Used 4” Leesona traverse winder, model 955, two position winder equipped with 1.5 HP motor. 127/220V, 60Hz, 3 Phase. Serial Number: 4918-19 (Located in Scotia, NY) (Rig/Load Fee $150)
Lot # 18 – Used 82” Valmet Two Drum Winder
Used 82” Valmet Two Drum Winder, equipped with 60" maximum diameter shaftless unwind with roll lift, 12" Wichita Magnum disc brakes, Wichita Micro Controller tension control, shear slitting, driven rider roll, 50" maximum diameter rewind, 55 HP AC motor, AC drive, and J table. Maximum Mechanical Speed Rated For 3000 FPM. (Located in Scotia, NY) (Rig/Load Fee $900)
Lot # 19 – Used Custom Multi-Head Tape Winder
Used Custom Multi-Head Tape Winder, equipped with twenty (20) winding heads good for up to 0.75" wide material, winding on 3" cores, operator control panel. (Located in Scotia, NY) (Rig/Load Fee $100)
Lot # 20 – Used 62” Custom Single Position Unwind
Used Custom Single Position Unwind good for 40" maximum diameter rolls and equipped with lead out idler roll, 2" diameter solid shaft. No brake. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 21 – Used 30” Elsner Single Position Unwind
Used 30” Elsner single position unwind with 40" maximum roll diameter, equipped with two (2) 3" air shafts, 6" disc brake, roll follower, side lay base for edge guiding. (Located in Scotia, NY) (Rig/Load Fee $250)
Lot # 22 – Used 36” Custom Single Position Unwind
Used 36” Custom Single Position Unwind with 70” maximum roll diameter,and equipped with side lay base for edge guiding with hydraulic cylinder (no pump), 16" Warner electric brake, no unwind shaft. (Located in Scotia, NY) (Rig/Load Fee $100)
Lot # 23 – Used 28” Elsner Single Position Unwind
Used 28” Elsner single position unwind with 40" maximum roll diameter, and equipped with 10" disc brake, follower arm for tension control, 3" air shaft, sidelay base for edge guiding, and roll lift cradle. (Located in Scotia, NY) (Rig/Load Fee $250)
Lot # 24 – Used 17” Hamilton Single Position Unwind
Used 17” Hamilton single position unwind with 50" maximum roll diameter and equipped with 5" diameter air shaft, splice board, dancer, and floor pick up. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 25 – Used 17” Hamilton Single Position Unwind
Used 17” Hamilton single position unwind with50" maximum roll diameter and equipped with 5" diameter air shaft, splice board, dancer, and floor pick up. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 26 – Used 62” Arrow Single Position Unwind
Used 62” Arrow Single Position Unwind with 40" maximum roll diameter and equipped with a 12" Montalvo disc brake, lead in idler rolls, sidelay base for edge guiding, skewing, shafted for 6" diameter cores. (Located in Scotia, NY) (Rig/Load Fee $100)
Lot # 27 – Used 64” Black Clawson 30 Turret Unwind
Used 64” Black Clawson turret unwind with 50" maximum roll diameter on 3" and 6" cores, and equipped with 2-direction automatic splicer, adjustable arms for varying width cores, dual speeder belt (parent roll speed up for over & under unwinding), 14" Montalvo disc brakes, nine (9) 3" air shafts, two (2) 6" air shafts, eleven (11) 5" air shafts, four (4) 8"air shafts, load cell tension control, sidelay base for edge guiding.Mfr Date: 1983. Serial Number: 3172-83 (Located in Scotia, NY) (Rig/Load Fee $1,100)
Lot # 28 – Used 52” Hirano Tecseed Turret Unwind
Used 52” Hirano Tecseed Turret Unwind with 40" roll diameter,2-position turret equipped with automatic splicer, automatic tension control, 6" chucks.Mfr Date: 1991. (Located in Scotia, NY) (Rig/Load Fee $600)
Lot # 29 – Used 42” Custom Single Position Rewind
Used 42” Custom single position rewind with 40” maximum roll diameter and equipped with Reliance 2HP motor with 10:1 gear box, 3" diameter air shaft, safety chucks, 4.25" bowed roll, air operated rider roll, sidelay base for edge guiding. (Located in Scotia, NY) (Rig/Load Fee $100)
Lot # 30 – Used 30” Lembo Single Position Rewind
Used 30” Lembo Single Position Rewind equipped with 36" maximum diameter primary rewind and 24" maximum diameter auxiliary winder (no shaft), air-operated rubber-covered rider roll on primary rewind, dancer roll assembly, air operated chucks on each rewind, 7-1/2 HP Allen-Bradley motor on primary rewind, sidelay base, 3 HP Allen-Bradley motor on auxiliary rewinder, and explosion-proof controls. Serial Number: A-34026 (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 31 –Used 54” Custom Single Position Rewind
Used 54” Custom Single Position Rewind equipped with a 40" maximum diameter primary rewind, 40" maximum diameter stripper/peeloff rewind; Superchuck safety chucks, steel shafts, and 6" diameter pneumatic chucks at main and stripper rewind positions; lead-in idler roll, E-stops, 1/4 HP DC motor (120 VDC). (Located in Scotia, NY) (Rig/Load Fee $100)
Lot # 32 – Used 82” Black Clawson Model 40 Turret Rewind
Used 82” Black Clawson Turret Rewind, Model 40 designed for 50" maximum diameter rolls, and equipped with 6" diameter lug-type air shafts, Comptrol load cell, roll unloading table on tracks with shaft puller, roll changer for automatic operation, operator console. DC motors but no drive included. Serial Number: M-1963-83, 303E277319 (This item is uninstalled and currently stored in a climate controlled warehouse.) (Located in Scotia, NY) (Rig/Load Fee $1,500)
Lot # 33 – Used 52” Sherman Dual Position Rewind
Used 52” Sherman dual position rewind with 24" diameterrolls and equipped with two (2) 3" button-type air shafts, 0.75 HP Synchrogear motor with clutches. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 34 – Used 60” Contech Surface Unwind
Used 60”Contech Surface Unwind with 40" maximum roll diameter for running light-weight roll goods, Horton disc brake. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 35 – Used 16” Comco Commander 4-Color Flexographic PressWith Coater Laminator
Used 16” Comco Commander Flexographic Press equipped with a 40" maximum diameter single position floor pickup primary unwind, four (4) flexo stations with dryer at each station and turn bar between flexo station 1 and 2, gravure coating station with 12' gas-fired vertical "U" oven with driven idler rolls, Crosfield registration control, automatic tension control, 20" single position auxillary unwind, laminating station, die cutting station, 40" maximum diameter single position rewind, Sterlco model M2B temperature controller, Magnetek DC drive. Machine was completely rebuilt in 1999. Press was running 12 pt. board then laminating 1.2 mil film to it. (Located in Scotia, NY) (Rig/Load Fee $1,150)
Lot # 36 – Used 52” Egan Bone Craven Gravure Coating Head
Used 52” Egan Bone Craven coating head, a 2-roll direct gravure coating station equipped with infeed idler roll, 10" diameter gravure roll, 9" rubber-covered roll, enclosed doctor blade, spare gravure roll. (Located in Scotia, NY) (Rig/Load Fee $150)
Lot # 37 – Used 90” Dahlgren LAS 90 LSP Moisturizer
Used 90” Dahlgren coating head, Model LAS 90 LSP moisturizer, equipped with 10" diameter x 94" face rubber-covered metering roll, 14" diameter x 94" face chrome-plated hydrophilic roll, 8" diameter x 94" face diameter lift rolls, Reeves drive on metering roll, 15 HP motor on transfer roll(no controller), spare transfer roll and spare metering roll.Mfr Date: 1983. Serial Number: 300 83 (Located in Scotia, NY) (Rig/Load Fee $250)
Lot # 38 – Used 42” Liberty Mayer Rod Coating Head
Used 42” Liberty coating head equipped for Mayer rod coating with 8" diameter applicator roll, single rod position, coating pan, 5.25" bowed roll, lead in and lead out lift rolls, smoothing roll, vacuum pull roll section, explosion proof motors. (Located in Scotia, NY) (Rig/Load Fee $100)
Lot # 39 – Used 82” Zink Offset Gravure Coating Head
Used 82” Zink Offset Gravure Coating Head equipped with 3-roll vertical stack with 16" diameter gravure roll, 13" diameter rubber-covered roll, 16" diameter steel roll, Harris & Bruno chambered doctor blade (new), operator control panel, and mechanical drive with DC motors. Includes spare rolls, spare doctor blade assembly, and spare coating tray.Mfr Date: 1992. (Located in Scotia, NY) (Rig/Load Fee $850)
Lot # 40 – Used 67” Custom 3-Roll Coating Head
Used 67” Custom Coating Head, a 3-roll coater equipped with two (2) 10" diameter chrome-plated rolls, one (1) 10" diameter rubber-covered applicator roll, and three (3) DC motors (7.5 HP, 7.5 HP, 7.5 HP). (Located in Scotia, NY) (Rig/Load Fee $200)
Lot # 41 – Used 68” Black Clawson 4-Roll Contra Coating Head
Used Black Clawson Coating Head, a 4-roll Contra Coater equipped with heavy duty structural frame, 10" diameter gravure roll, 10" diameter rubber-covered applicator roll, 10" diameter chrome-plated back-up roll, doctor blade, coating pan, and motor stand with four (4) DC motors (5 HP, 5 HP, 5 HP, 7.5 HP). (Located in Scotia, NY) (Rig/Load Fee $200)
Lot # 42 – Used 84” Jagenberg Convo 23 Folio Sheeter
Used 84” Jagenberg Folio Sheeter, model Convo 23, having a 24" - 80" cutoff range, two (2) 60" maximum diameter 4-roll unwind stands, decurling station, 72" piler, pile sheet stacker with dual shuttle tables, variable speed controls, and counter. Maximum design speed: 850 FPM. Maximum cut speed: 400 cuts per minute.Mfr Date: 1973. Serial Number: 30.61926 (Located in Memphis, TN) (BUYER responsible for rigging & removal)
Lot # 43 – Used 44” Custom Decurler
Used 44” Custom decurler equipped with 1" diameter decurler bar backed by multiply bearing supports, motorized control, lead in and lead out idler rolls, mounted on fabricated steel frame. (Located in Scotia, NY) (Rig/Load Fee $75)
Lot # 44 – Used 40” Contech Portable Knife Sheeter