GUIDE SPECIFICATION FOR ULTRITE® DEGREASER: HEAVY DUTY CONCRETE DEGREASER AND STRIPPER

SECTION 03 01 30.51

CLEANING OF CAST-IN-PLACE CONCRETE

Specifier Notes: This guide specification is written according to the Construction Specifications Institute (CSI) format. The section must be carefully reviewed and edited by the architect or engineer to meet the requirements of the project. Coordinate this section with other specification sections and the drawings.
Specifier Notes: ULTRITE DEGREASER is a heavy-duty concrete degreaser and stripper, which will biodegrade. It naturally and safely replaces mineral spirits and chlorinated solvent-based heavy-duty concrete degreaser products.
ULTRITE DEGREASER penetrates concrete surfaces on contact to soften, lift, and remove a wide range of oils, polymers, fats, and greases. Use ULTRITE DEGREASER to remove dirt, tire marks, oil spills, grease, and other contaminants. It will also remove most curing compounds and cure/seals from concrete floors. Periodic stripping of concrete floors is in keeping with good concrete maintenance practices. It is ideal for use in warehouses, industrial plants, food processing plants, schools, automotive plants, parking garages, plazas, and service stations - anywhere cleaning and stripping of concrete surfaces is required.

PART 1 GENERAL

1.01SECTION INCLUDES

A.Application of a heavy duty concrete degreaser and stripper on masonry or concrete surfaces.

1.02RELATED SECTIONS

Specifier Notes: Edit the list of related sections as required for the project. List other sections dealing with work directly related to this section.

A.Section 0330 00 - Cast-in-Place Concrete.

1.03REFERENCES

A.ACI 515.1R - Guide to the Use of Waterproofing, Dampproofing, Protective, and Decorative Barrier Systems for Concrete.

1.04SUBMITTALS

A.Comply with Section 0133 00 - Submittal Procedures.

B.Submit manufacturer's product data and application instructions.

1.05DELIVERY, STORAGE, AND HANDLING

A.Deliver materials to site in manufacturer's original, unopened containers and packaging, with labels clearly identifying product name and manufacturer.

B.Store materials in a clean, dry area in accordance with manufacturer's instructions.

C.Keep product from freezing.

D.Avoid direct contact with this product as it may cause mild-to-moderate irritation of the eyes and/or skin.

E.Protect materials during handling and application to prevent damage or contamination.

F.Use product full strength from the container.

G.Dispose of material according to all local, state and federal regulations.

1.06ENVIRONMENTAL REQUIREMENTS

A.Do not apply if the temperature of the concrete is less than 35°F (2°C) or above 130°F (57°C).

PART 2 PRODUCTS

2.01MANUFACTURER

A.W.R. MEADOWS®, INC., PO Box 338, Hampshire, Illinois60140-0338. (800) 342-5976. (847) 683-4500. Fax (847) 683-4544. Website

2.02MATERIALS

A.ULTRITE DEGREASER heavy duty, biodegradable concrete degreaser and stripper by W.R. MEADOWS.

PART 3 EXECUTION

3.01EXAMINATION

A.Examine surfaces to receive concrete degreaser. Notify architect if surfaces are not acceptable. Donot begin application until unacceptable conditions have been corrected.

3.02SURFACE PREPARATION

A.Protect adjacent surfaces not designated to receive concrete degreaser.

B. Follow ACI Guide 515.1R (Section 3.4.2) for severe oil and grease stains.

3.03APPLICATION

A.Apply concrete degreaser according to manufacturer’s instructions ensuring that all coverage rates are followed.

B.Apply concrete degreaser full strength from the container to the entire surface to be cleaned.

C.Allow concrete degreaser to soak in and soften the coating or stain.

D.Apply additional concrete degreaser to prevent the surface from drying.

E.Thoroughly scrub the treated area with a stiff bristle broom or mechanical scrubber.

F.Rinse the area with large amounts of clean water.

G.Continue to rinse with water until there is no visible trace of the product on the concrete.

H.Test patch the dry concrete prior to painting or applying a subsequent surface treatment.

I.Clean the concrete with additional degreaser if stain or coating has not been completely removed.

3.04CLEANUP

A.Dispose of material according to local, state, and federal regulations.

B.Clean all tools and equipment with water.

END OF SECTION

Project Name9/21/201803 01 30.51-1Cleaning of Cast-In-Place Concrete