EC declaration of conformity of an EATMN Constituent

EC Regulation No 552/2004, the interoperability Regulation, Article 5 and Annex III (3) as amended by EC Regulation No 1070/2009

Page 1

EC declaration of conformity of the EATMN constituent

(Name of Constituent[1])

I –Manufacturer of the EATMN constituent
The name and address of the manufacturer or its authorised representative established within the Community (give trade name and full address and, in the case of the authorised representative, also give the trade name of the manufacturer)
II –Description of the EATMN constituent
Brief description and identification of the EATMN constituentincluding its interfaces covered by the declaration.
When the manufacturer has developed an EATMN representation[2] as described in section 3 of the EUROCONTROL Guidelines on conformity assessment for the interoperability Regulation of the single European sky(Edition 3.0 dated 20/02/2012), it can be used for the purpose of this description.
III – Conditions of Use
  • Description of the air traffic environment of the constituent
  • Key performance indicators of the EATMN constituent (static and/or dynamic configuration parameters such as limits, message throughput, number of users, number of aircraft supported, etc.)

IV - Regulation references
List of essential requirements of the interoperability Regulation and relevant regulatory provisions of implementing rules on interoperability met by the EATMN constituent.
This corresponds to the regulatory baseline of section 4.2 of the EUROCONTROL Guidelines on conformity assessment for the interoperability Regulation of the single European sky (Edition 3.0 dated 20/02/2012).
V – Means of Compliance
Community specifications
This corresponds to the MoC baseline of section 4.3 of the EUROCONTROL Guidelines on conformity assessment for the interoperability Regulation of the single European sky (Edition 3.0 dated 20/02/2012).
Identifythe Community specifications to which the EATMN constituent complies:
  • Community specifications listed in the Official Journal of European Union which are either:
  • European Norms (EN) giving a presumption of conformity with the corresponding regulations identified in IV and implemented by the EATMN constituent.
  • EUROCONTROL Specifications giving a presumption of conformity with the corresponding regulations identified in IV and implemented by the EATMN constituent.

VI – Accompanying documents
List of documents delivered with the EC declaration of conformity:
  • Manual for the installation, configuration, operation of the EATMN constituent etc.
Each document must be dated and signed.
VII–Description of the procedure
  • Description of the procedure followed in order to declare conformity (Article 5 of the interoperability Regulation):
  • Role(s) of the manufacturer in the procedure
  • When used, the module(s) of Decision No 768/2008/EC that were applied during the procedure
  • If applicable
  • The name, address and identification number of the notified body that was involved in the procedure
  • Role(s) of the notified body in the procedure
  • When used, the module(s) of Decision No 768/2008/EC applied during the procedure
  • The date of examination certificate together, where appropriate, with the duration and conditions of validity of the certificate

EC declaration of conformity of the EATMN constituent

(Name of constituent)

  1. The object of this declaration is the EATMN constituent as described in II.
  1. The conditions of use of this EATMN constituent are defined in III.
  1. The documents accompanying this declaration are listed in VI.
  1. The verification of compliance of this EATMN constituent with regulations identified in IVhas been carried out in accordance with procedures defined in VII.

This declaration is issued under the sole responsibility of the manufacturer. Ideclare on behalf of(name of the manufacturer)that the EATMN constituent described in II has been assessed to

  • meet the essential requirements and regulatory provisions identified in IV, and
  • considered in isolation, conform with the Community specification(s) identified in V.

Name, Position and Signature:

(Name, position/function and signature of the person empowered to enter into commitments on behalf of the manufacturer)

Date and Place of Issue:

This Declaration is valid[3] until:

Page 1

[1]The explanatory blue text is to assist the completion of the declaration and is to be replaced by the appropriate content.

[2] The EATMN representation may have been developed to describe large and/or complex products.

[3]Certificate(s) issued by notified bodies may have a validity period thereby impacting the validity period of this declaration. If applicable, enter the validity date for the declaration or remove this clause from the declaration.