Technical Data
(150) 300 750 1500 3000 6000
Max load150 kg 300kg750kg1500kg3000kg6000kg
- Arm length500 mm 650 mm1000 mm1400 mm1400 mm2200mm
- Stand width600 mm712 mm855 mm 960 mm 1660 mm1512mm
- Stand depth500 mm860 mm1005 mm1200 mm1380 mm1700mm
- Body width458 mm560 mm 700 mm 770 mm 907 mm1294mm
- Body depth660 mm570 mm720 mm840 mm1090 mm1082mm
- Total depth1450 mm1950 mm2580 mm3320 mm3420 mm4715mm
- Body height1950 mm1880 mm2410 mm2410 mm2605 mm3191mm
R. Rear cabinet 440 mm 560 mm 700 mm 795 mm 795 mm 1240mm
X- vertical 435-1215 mm 540-1320 mm 720-1740 mm 675-1695 mm 835-1855 mm 940-2105mm
Y- rotation unlimited unlimited unlimited unlimited unlimited unlimited
Z- rotation unlimited unlimited unlimited unlimited unlimited unlimited
Max lift speed 4,8 m/min 4,5 m/min 3,5 m/min 7 m/min 3,5 m/min 1,0 m/min
Max rotation speed –Y 5 rpm 6,5 rpm 3,5 rpm 2,7 rpm 2,7 rpm 1,6 rpm
Max rotation speed –Z 5 rpm 6,5 rpm 3,5 rpm 2,7 rpm 2,7 rpm 2,7 rpm
Motor effect tot. kW/A 0,7/10 2,25/16 4,5/25 7,4/25 8,2/25 10,7/25
Connecting power. V 230 400 400 400 400 400
Size 150 is no longer manufactured
Fixture Plate
150 300750 1500 3000 6000
S 330 mm 360 mm 500 mm 520 mm 520 mm 800mm
C – C 294 mm 320 mm 440 mm 440 mm 440 mm 720mm 18 mm 18 mm 25 mm 25 mm 25 mm 30mm
R R ¼ R ½ R ½ R ½ R ½ R ½
Volume – Work Piece (standard arm length )
150 300 750 1500 3000 6000
D 1000 mm 1300 mm 2000 mm 2800 mm 2800 mm 4400 mm
h 1140 mm 1290 mm 1690 mm 1260 mm 1260 mm 1180 mm
H 1350 mm 1465 mm 2000 mm 2000 mm 2000 mm 2400 mm
Accessories
External speed regulation of rotating axis.
Adjustable speed of rotating axis (Y or Z).
Also allows to change the rotation in already programmed positions.
Connect to the side of the machine.
The speed control can be activated in both programmable and manual driving.
Speed regulation is ideal If a rotating axis is used for welding of circular constructions.
Of course foot pedal or hand control can be used instead of micro switches.
Micro Switches (2 pcs) with 5 m cable (instead of foot pedal).
In some situations it can be useful to have the driving button nearby.
The micro switches can be mounted on the operation handle of the welding machine.
Set a low speed with the speed regulation and hold the micro switches
while welding.
This will speed up the welding process and also produce a better welding quality.
Program Selectors, 0-9 or 0-99.
By using the control panel you can find your stored programs by searching in the block numbers. The program starts on a certain block number.
This is a good solution with just a few programs.
When there are several programs stored there sometimes can be a bit difficult to find the right program. The program selectors helps you to faster find the right program just by using the switches. Turn the switches and start the program.
Pneumatic supply.
Fixture locking is sometimes controlled by pneumatic.
By using swivels in both cabinet and arm air is available in the fixture plate.
Just plug air into the side of the machine.
Max air pressure 10 bar.
ErgoCom
This program allow you to save your programs on computer.
Just connect to a computer via a RS232-cable and start the program.
The program works both ways, load or store.
The main purpose is to store programs as a back up in case the system fails or someone accidentally change the program.
This is very useful when many programs are used.
You need to have Windows 95/NT as your operation system.