Food Service Equipment Contractor to Move Four (4) Existing

Food Service equipment Contractor to move four (4) existing

appliances to the left 10” on the existing a la carte cooking line (in plan view) and provide new 48” Dormont double swivel quick disconnects for these items.

ITEM NO 3 PLATFORM SCALE

Quantity Req'd.: 1

Status: Existing/Relocate

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by Product Supplier/ Vendor. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 4 - SPARE NUMBER -

ITEM NO 5 - SPARE NUMBER -

ITEM NO 6 - SPARE NUMBER -

ITEM NO 7 ICE MAKER W/ BIN

Quantity Req'd.: 1

Manufacturer: Hoshizaki

Model No.: 1300

Status: Existing/Relocate

Connect to item 9, water filter.

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 8 ICE MAKER WITH BIN

Quantity Req'd.: 1

Manufacturer: Hoshizaki

Model No.: HOSHI

Status: Existing/Relocate

Connect to item 9, water filter.

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 9 WATER FILTER

Quantity Req'd.: 1

Manufacturer: Everpure, Inc

Model No.: EV9347-20

Status: In Contract

Provide with:

Replacement cartridge EV9613-10

EC210 prefilter cartridge.

SS-IMF Cartridge EV9799-32

Connect to items 7 and 8.

ITEM NO 10 FLOOR TROUGH

Quantity Req'd.: 1

Manufacturer: IMC/Teddy

Model No.: SFT

Status: In Contract

Unit of size and shape as shown on plan. This item to be set and installed by General Contractor. Quarry tile floor finish to be etched, if required, prior to setting food service equipment in place. Provide grating sections of equal size not to exceed 20" long. Provide shop drawings of size and scale outlined in specific conditions.

Grating to be anti-slip, stainless steel.
Shallow floor trough, 2" deep
Standard troughs up to 96" long have one waste at center. Over 96", troughs have two wastes equidistant.
Seepage flange and "weep" holes (for above grade application only).

ITEM NO 11 - SPARE NUMBER -

ITEM NO 12 - SPARE NUMBER -

ITEM NO 13 - SPARE NUMBER -

ITEM NO 14 HAND SINK

Quantity Req'd.: 4

Manufacturer: IMC/Teddy

Model No.: CSW

Status: In Contract

IMC/Teddy Model No. CSW, Hand Sink.

Heavy duty gooseneck faucet w/wrist handles.
Provide hose bibs under 2 units.

ITEM NO 15 SHELVING

Quantity Req'd.: LOT

Manufacturer: Metro Equip

Model No.: Super Erecta

Status: In Contract

Metro Equip Model No. SUPER ERECTA, Of size and shape as shown on plan x 4 tiers high. 74" high posts to match shelf type.

ITEM NO 16 - SPARE NUMBER -

ITEM NO 17 DUNNAGE RACK

Quantity Req'd.: 1

Manufacturer: Metro Equip

Model No.: MHP55K3

Status: In Contract

Dunnage Rack.

Furnish per manufacturer's standard specifications.

ITEM NO 18 RACK, UTILITY - UNIVERSAL ANGLE

Quantity Req'd.: 2

Status: Existing/Relocate

ITEM NO 19 - SPARE NUMBER -

ITEM NO 20 - SPARE NUMBER -

ITEM NO 21 FISH AND POULTRY STORAGE RACK

Quantity Req'd.: 1

Manufacturer: Refrigerator Manufacturers Inc.

Model No.: CXA-619

Status: In Contract

Provide with 3 McClintock lugs 11” H x 19” W X 25” D

ITEM NO 22 SHELVING

Quantity Req'd.: LOT

Manufacturer: Metro Equip

Model No.: METROSEAL 3

Status: In Contract

Of size and shape as shown on plan x 4. 74" high posts to match shelf type. 5" diameter polyurethane swivel casters, two (2) with brakes.

ITEM NO 23 CABINET, UTILITY

Quantity Req'd.: 3

Status: Existing/Relocate

ITEM NO 24 WALK-IN COOLER

Quantity Req'd.: 1

Manufacturer: Kolpak Ind Inc

Model No.: Custom

Status: In Contract

Kolpak Ind Inc COOLER/ FREEZER Unit to be a Refrigerator +35° F. and Freezer -10° F. of size and shape as shown on plan 8'-6" high. Wall and ceiling panels shall be 4" urethane, U.L.Flame Spread 25 insulation. Panels are without wooden structural members. Hinged entrance door(s) to be flush type, hinged as shown on plan. Thru ceiling door electrical assembly as shown on detail E-1-4. Provide one (1) lot removable closure panels with channels, the same finish as exterior panels to ceiling. (F.S.E. Contractor to verify ceiling height). One (1) lot of trim strip, where required to close in wall gaps, of same finish as exterior panels to finished ceiling. (F.S.E. Contractor to verify height).

Combination cooler/ freezer. Cooler with 2” factory floor in cooler and 4” factory floor in freezer with internal ramp.

Protect-all vinyl finish flooring coved 6” to all interior walls to be provided and installed by FSEC.
Embossed aluminum white interior and exposed exterior. Unexposed exterior finish to be galvalume.
Hinged doors to be 36" wide x 78" high with third hinge.
Dead bolt lock per Specific Conditions (on exterior doors only)
Anti-condensate heaters in full perimeter of door and frame (freezer only)
Aluminum diamond tread kick plate, 3'-0" high on exterior and interior of door and jamb
14" x 14" vision panel and automatic door closer, Kason K-1094.
Factory cut door for tile floor conditions.
Lithonia florescent light fixtures and switches, installed and wired by the Electrical Division per detail E-1-4. (See electrical plan for quantity and location of lights and switches).]
Modularm 75B, recessed with thru ceiling door electrical as shown on detail E-1-4.
FSE Contractor to provide complete and operable refrigeration system.

ITEM NO 25 TABLE, ISLAND TYPE

Quantity Req'd.: 1

Manufacturer: Custom Fabricated Assembly,

Status: In Contract

Unit to be of size and shape as shown on plan x 36” high per detail C-7-1C. Type “A” edge per detail C-1-1A. Provide with the following:

One -20" x 20" x 5" deep utility drawer per detail C-1-3A,C-1-3B, C-1-3C and C-1-3D. Lock hasp.

Mount on set of 5" diameter polyurethane swivel casters, two (2) diagonal with brakes.

ITEM NO 26 COUNTERW/2-SINKS

Quantity Req'd.: 1

Status: Existing/Relocate

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 27 RACK, WORKING HEIGHT

Quantity Req'd.: 2

Manufacturer: Eagle

Model No.: OUR-1807-3-SR

Status: In Contract

Panco aluminum pan stop

Casters with locking brakes, set of 2

ITEM NO 28 BUTCHER BLOCK

Quantity Req'd.: 1

Status: Existing/Relocate

ITEM NO 29 SAW, MEAT 16" CUT CLEARANCE

Quantity Req'd.: 1

Status: Existing/Relocate

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 30 - SPARE NUMBER -

ITEM NO 31 - SPARE NUMBER -

ITEM NO 32 SPREADER CABINET

Quantity Req'd.: 1

Manufacturer: Garland Ind

Model No.: M12ES

Status: In Contract

Spreader Plate, approximately 12" wide top, cabinet base with one door, stainless steel top, left side and front, for 38" deep range units.

ITEM NO 33 EXHAUST HOOD, WALL MOUNTED

Quantity Req'd.: 1

Manufacturer: Gaylord, Inc.

Model No.: Island GX2-BDL

Status: In Contract

Unit to be U.L. listed grease extractor, high velocity wall mounted canopy of size and shape as shown on plan 9’-6"x 68” deep x 30" high, built in 1 section(s) and mounted 6'-8" AFF. One (1) lot stainless steel enclosure paneling, at all open sides, to finished ceiling (F.S.E. Contractor to verify height). Paneling must be supplied by Exhaust Hood Manufacturer and installed by F.S.E. Contractor. Adhere to Specific Conditions for installation of fabricated equipment." Ventilator to be U.L. and NSF listed and be in full accordance with NFPA 96 and all state/local codes/ordinances applicable. F.S.E. Contractor to supply the necessary mounting rods for hanging ventilator. Supply and/ or exhaust air requirements as shown on plans.

Options:

Recessed incandescent light fixtures as indicated on electrical plan.
Exhaust collar(s) with thermostatically activated fire damper,
Pre-piping of the Item No 165, Fire protection system is to be provided by the Exhaust Hood manufacturer at the time of hood fabrication.
Pre-piping to include fusible-link detector bracket assemblies and cable runs, and wet-chemical manifold piping, duct collar and plenum protection piping with termination nozzles, and cooking appliance nozzle drops with termination nozzles.
Location of cooking appliance nozzle drops are to be fully dimensioned on hood submission drawings.
Fusible link detector and wet chemical piping terminations to be coordinated with the FSE Contractor and clearly indicated on hood submission drawings.
Access to the fusible links for inspection and change-outs to be provided. The hood manufacturer and FSE Contractor to coordinate their efforts to assure the necessary access.

FSE Contractor is responsible for fit of equipment. Prior to releasing hoods for fabrication, FSE Contractor needs to verify field conditions (existing &/or proposed) and to determine clearances to all structural items, obstructions, etc. The FSE Contractor will coordinate with other trades to confirm that the hood can be mounted as proposed and that the ductwork and final connection can be accommodated without conflict. Failure to perform this step may result in modifications to the exhaust hood at the FSE Contractor's expense.

ITEM NO 34 WALL FLASHING, STAINLESS STEEL

Quantity Req'd.: 1

Manufacturer: Custom Fabricated Assembly,

Status: In Contract

Provide 22 ga. stainless steel wall flashing, approximately ' per detail C-2-11. Stainless steel flashing to extend from floor or top of wall tile base to top of 48” high wall with s.s. wall cap per detail ED-106

ITEM NO 35 OVEN, CONVECTION, GAS

Quantity Req'd.: 1

Manufacturer: Blodgett Co.

Model No.: DFG100 DOUBLE X-CEL

Status: In Contract

Oven, Convection, Natural gas

Solid State digital control with LED display, cook & hold, and Pulse Plus and humidaire control.
4.25" low profile casters (double only)
Flexible gas hose w/quick disconnect & restraining device.
Interior liner stainless steel.
Solid back and right side panel stainless steel
Gas manifold (double section).

ITEM NO 36 RANGE, HEAVY DUTY GAS

Quantity Req'd.: 1

Manufacturer: Garland

Model No.: M43R

Status: In Contract

Range, Heavy-Duty, Gas-Fired

Provide with the following:

¾” rear gas connection.
Right and left end caps.
Provide with flexible gas disconnects.
10” flue riser.
4 swivel casters, two locking.
Provide with shield 12” tall on right side

ITEM NO 37 KETTLE & POT FILLER

Quantity Req'd.: 1

Manufacturer: T & S, Inc.

Model No.: B-0610

Status: In Contract

Faucet, Service Sink. Mount on wall behind item 32, spreader.

ITEM NO 38 FRYER, DEEP FAT, GAS-FIRED

Quantity Req'd.: 1

Manufacturer: Vulcan-Hart

Status: Existing/Relocate from main cooking line.

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 39 UTILITY CHASE

Quantity Req'd.: 1

Manufacturer: Custom Fabricated Assembly,

Status: In Contract

Unit to be a divided chase of size and shape as shown on plan per detail C-2-12. F.S.E. Contractor to verify ceiling height. Unit to be built as a part of item 42, table with sink.

Extend chase to finished ceiling.

ITEM NO 40 CABINET, WALL-MOUNTED

Quantity Req'd.: 1

Status: Specified By Architect/Interior Designer

ITEM NO 41 OFFICE CHAIR

Quantity Req'd.: 1

Status: Specified By Architect/Interior Designer

ITEM NO 42 TABLE W/SINK, TABLE MOUNTED OVERSHELF

Quantity Req'd.: 1

Manufacturer: Custom Fabricated Assembly,

Status: In Contract

CUSTOM FABRICATE, Unit to be of size and shape as shown on plan x 36” high per detail C-7-1B and C-8-5 with Type “V” edge per detail C-1-1A, one 20” x 20” x14” deep drawn sink, closed backsplash per detail C-1-1B.

Flanged feet.
Provide with type 3 faucet w/ 12” swing spout.

One -20" x 20" x 5" deep utility drawer per detail C-1-3A,C-1-3B, C-1-3C and C-1-3D. Lock hasp.
Provide with table mounted overshelf and utensil rack per details C-1-6 and C-7-5

ITEM NO 43 FREEZER, 1-SECTION

Quantity Req'd.: 1

Manufacturer: HOSHIZAKI

Status: Existing/Relocate

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 44 TABLE W/ TABLE MOUNTED SHELF

Quantity Req'd.: 1

Manufacturer: Custom Fabricated Assembly,

Status: In Contract

CUSTOM FABRICATE, Unit to be of size and shape as shown on plan x 36” high per detail C-7-1C and C-8-5 with continuous seamless flush front Type “V” edge per detail C-1-1A, closed backsplash per detail C-1-1B.

Provide with table mounted overshelf per details C-1-6.
Mount on set of 5" diameter polyurethane swivel casters, two (2) diagonal

with brakes.

ITEM NO 45 VACUUM PACKAGING UNIT

Quantity Req'd.: 1

Manufacturer: Vacmaster

Model No.: SVP-20

Status: Existing/Relocate

This item is not in contract. The specification is for reference only. The item is shown on the drawing for informational purposes and generally represents the size/ capacity of unit to be provided by the owner. Any utility connections indicated on drawings are representative and intended to assist the Engineer in planning base building utility systems. Utility requirements for existing equipment or equipment provided by a product supplier will be confirmed by the FSE Contractor and represented on the dimensioned rough-in plans for use by the construction trades.

ITEM NO 46 FISH PREP STATION

Quantity Req'd.: 1

Manufacturer: Custom fabricated

Status: In Contract

Custom fabricated, Sink Work Table, One Compartment, stainless steel top, w/raised-inverted “V” non-spill edges, 10" w/rear, left & right-hand splash, stainless steel open frame base, with stainless steel tubular undershelves per detail C-8-5-C and C-7-1. Size and shape as shown on plan. Sink to be 5” deep. Provide with:

Fisher 2210-WB pre-rinse with 2901 Add on faucet
48" x 14" x 3/4" thick richlite cutting board inset in top.
Removable s.s. perforated false bottom w/1" finger hole.
Tool drawer w/padlock hasp per details C-1-3-A,B,C,D.
Integral hand sink below top per detailC-2-1-D

ITEM NO 47 - SPARE NUMBER -

ITEM NO 48 - SPARE NUMBER -

ITEM NO 49 - SPARE NUMBER -

ITEM NO 50 - SPARE NUMBER -

ITEM NO 51 REFRIGERATOR, 1-SECTION

Quantity Req'd.: 1

Manufacturer: Beverage Air

Model No.: MT 12 Marketeer

Status: In Contract

Refrigerator, 1-Section

Provide with glass door hinged per plan drawing.
Furnish w/ cord & plug
Unit to be on swivel casters, 2 locking.
Door w/ cylinder lock.
Provide five (5) year compressor warranty and one (1) year refrigeration service contract.
Provide condensate evaporator.

ITEM NO 52 FIRE SUPPRESSION SYSTEM

Quantity Req'd.: 1

Manufacturer: Kidde

Model No.: WHDR

Status: Existing/Relocate/Modify or replace

The cooking line has been expanded by 69” to provide items 117, 118, 119, and 120. As this now becomes all in the same hazard zone, the existing system must be moved to a new location and modified or replaced with a new system. FSEC to confirm with fire suppression sub-contractor what will be required prior to bid submission. No allowance will be made later for additional cost not anticipated at the time of bid.