Siemens Energy & Automation, Inc.

Process Instrumentation Business Unit

CoC Ultrasonic Flow

155 Plant Avenue ▪ Hauppauge ▪ New York 11788 ▪ USA ▪

Phone: (631)231-3600 ▪ 1-800-275-8479 ▪ Fax: (631)231-3334

email: ▪

SITRANS GAS Flow Meter

Application Information Form

Spool-Based Meter

Siemens Energy & Automation manufactures a complete line of Flow Meters. Completing this form will permit Siemens Energy & Automation Application Specialists to recommend the most suitable system for your applications.

(Refer to applicable product data sheet)

▪ Company Name:
▪ Street:
▪ City:
▪ State/Province:
▪ Postal code/Zip:
▪ Country: / ▪ First Name:
▪ Last Name:
▪ Phone:
▪ Email:
▪ Date: (mm/dd/yyyy)
▪ Technical Contact:

FOR MULTIPLE SITES, PLEASE FILL OUT ADDITIONAL FORMS IF DIFFERENT THAN ALREADY STATED.

Site name / Tag #

1)Application Information:

  1. Existing pipe size: O.D. in.mm Wall Thickness: in. mm
  2. FlowRange: Min Normal Max Units:
  3. Operating Pressure:Min Normal Max Units:
  4. Design Pressure:Max Units:
  5. Operating Temperature: Min Normal Max ºF ºC
  6. Design Temperature: (If different from operating)
  7. Straight run in pipe diameters: Up stream: Down Stream:
  8. Gas Condition: Wet-Gas%Moisture
  9. Flow condition Pulsating FlowSurge control Steady flow

Enter Gas Composition or attach analysis sheet

Mole Fraction List: / Methane / % / Carbon Dioxide / %
Ethane / % / Nitrogen / %
Propane / % / Hydrogen / %
Isobutane / % / Water / %
n-Butane / % / Oxygen / %
Isopentane / % / Hydrogen Sulfide / %
n-Pentane / % / Carbon Monoxide / %
n-Hexane / % / Other / %
  1. Is pipe pigged? NoYes
  2. If application and performance can be met, will user accept field clamp-on as alternative?

Yes No

2)Meter Body (Spool) Construction:

  1. Outside Diameter: in. mm
  2. Wall Thickness: in. mm
  3. Inside Diameter: in. mm
  4. Material: Carbon Steel (standard)Other

NACE MRO175/ISO15156 Other

  1. Pipe Code B31.8Location 3 (standard)Other
  2. Internal Surface Finish 125 micro inch (standard) Other
  3. ID Matching RequiredNo

Yes (upstream tube required) I.D.

  1. Flange Rating ANSI: Code B16.5 (standard) Other:

CL300 CL600 Other

Flange Type:Weld Neck (standard)Other:

Flange Facing:Raised Face (standard) Other:

  1. Upstream Tube requested: Yes No (If yes, specify length in pipe diameters)
  2. Flow conditioner (upstream tube required)

No CPA Specify other:

  1. Down stream tube requested:YesNo (If yes, specify length in pipe diameters)
  2. Additional Instrument ports¼” NPT pressure in meter body (standard)

Other specify size/type/qty (show using sketch below)

  1. Corrosive / offshore Environment:YesNo
  2. Safety approval Spool Body: Factory Mutual/CSA Class I, II Div 2 Class I, II Div 1

ATEX Zone 2 Zone 1 Zone 0

PED (pressure equipment directive)

  1. Paint Finish: 3 part epoxy/urethane (standard)Other: Specify
  2. Is there a Project specification? No Attached

3)Meter Electronics:

  1. Enclosure type: Nema 4X (IP 65)

Flame/explosion proof with display window

Flame/explosion proof without display window

(If none selected, quote will be made based on application and performance)

  1. Input Power:90-240 VAC 50/60hz

9-36 VDC Negative ground Positive ground

  1. Cable Length between Meter Electronics and Spool Body Feet Meters
  2. Request armored cable:No Yes
  3. Request Submersible cable: No Yes
  4. Communication: RS232 (standard)ModBus
  5. Analog outputs required:Specify Qty and type required:
  6. Meter Output (Pick One): Actual flow (uncorrected) OR

Standard volume or Mass (corrected)

Compensation type (only if corrected)AGA 8 Detailed, Other

  1. Mounting 2” stand pipe Wall Mount
  2. Operational Environment: IndoorsOutdoors

Corrosive EnvironmentOffshore

  1. Safety approval Electronics:Factory Mutual/CSA Class I, II Div 2 Class I, II Div 1

ATEX Zone 2 Zone 1

4)Performance Requirements:

  1. Required Accuracy: % of rate, Repeatability: %
  2. Flow Direction: Uni-directionalBi-Directional
  3. Performance Compliance: AGA-9 Other:
  1. Require an actual Gas Calibration Test and Report? NoYes

If Yes: Specify flow points Six point Seven pointother

Repeat points none one point two points,other

Calibration Pressure units

Specify Calibration flow range: min max units

Describe and/or Insert a photo or a sketch of the application and Up/Downstream piping conditions. (Remember to include control valves, elbows, other flowmeters, etc.): Simply copy and paste into this table. Bitmaps should be no larger than 640 X 480 Pixels.

Signature______Date______

CC544 Rev 3.0 Page 1 of 3