GPS Procedures.doc Updated: 3 Feb 04

Pacific GPS-based Monitoring System (GMS) Monitoring Procedures

Monitoring is required for all operators of aircraft that have received RVSM operational approval. Current monitoring goals should be reviewed for actual requirements; generally 2 or 3 aircraft of each type must be monitored. Monitoring requirements as well as other RVSM information can be found at the following web sites:

FAA RVSM

·  http://www.faa.gov/ats/ato/rvsm1.htm

Pacific Approvals Registry and Monitoring Organization (PARMO)

·  http://www.tc.faa.gov/acb300/parmo

Airworthiness Approval

In-production or new production aircraft attain airworthiness approval through verification of RVSM eligibility in the Airplane Flight Manual or Type Certificate Data Sheet. In-service aircraft attain airworthiness approval through the application of the type-specific RVSM Service Bulletin. The aircraft engineering requirements vary for individual types or groups of aircraft. These requirements may include upgrades to the air data computers, pitot-static modifications, skin waviness testing, and visual or paint inspections. After airworthiness approval is obtained, the operational approval process is completed by incorporation of RVSM policy and procedures into the training program, manuals, and maintenance program. Monitoring may be conducted after airworthiness approval information has been sent to the PARMO. Only airworthiness approved aircraft will be monitored.

PARMO

The PARMO is responsible for all monitoring activity and the operation of the GMS. CSSI Inc., the GMS support contractor, will assist the PARMO with the monitoring program.

GMS Description

The GMS is comprised of the equipment and procedures to collect and process three required data elements: GPS data, pressure altitude or Mode C data, and meteorological data. The GPS-based Monitoring Unit (GMU) is used to collect the GPS data during the monitoring flight. The PARMO, through the use of the attached Flight Information Form (FIF), will coordinate with the operator the collection of pressure altitude or Mode C data from ATC facilities. The operator will provide pressure altitude data from the digital flight data recorder (DFDR) of the aircraft being monitored. Late transmittal of the FIF and illegible or blank entries will delay processing and the dissemination of results. Meteorological data will be obtained by the PARMO without operator involvement.

Monitoring Flights

Monitoring flights do not need to be conducted in Pacific Airspace. Monitoring can be conducted on scheduled flights, ferry flights, or monitoring-specific flights. To ensure collection of sufficient position data, the flight must be straight and level at any altitude from FL290 to FL410, and should be at least thirty minutes in duration. Monitoring should also be conducted in areas where Mode-C radar data can be retrieved in a timely manner. In addition to Mode-C collected by the PARMO, the operator should provide pressure altitude data from the Digital Flight Data Recorder (DFDR) to the PARMO for Altimetry System Error (ASE) calculation.

GMU Description

The GMU is a portable unit comprised of a Global Positioning System (GPS) receiver, two GPS antennas, temporarily mounted on interior windows, and a laptop computer. The unit requires plug in power from the aircraft (draws 2.0 to 4.0 amperes maximum) and accepts multiple types of power standard to aircraft. The GMU can be installed in the aircraft cockpit or cabin, depending upon aircraft type. Installation time is approximately 15 minutes. For most transport aircraft, the GMU is best installed using the aft cockpit windows. The GMS Monitoring Specialist typically occupies a jump seat to monitor GMU performance. GMU installation is transparent crew operations.

Monitoring Process

Upon receiving airworthiness approval, the operator should contact the PARMO GMS Operations Coordinator to discuss monitoring options. To start the monitoring process the operator should submit the attached Monitoring Application to the PARMO. The Monitoring Application should include all aircraft that will be operated in the Pacific Region. The collection of GPS data with the GMU can be accomplished by a GMS Monitoring Specialist or by an operator representative that has received GMU training. The operator and the PARMO GMS Operations Coordinator will develop a mutually agreed upon plan for monitoring.

The operator will take the necessary steps to retrieve pressure altitude data from the digital flight data recorder (DFDR). The DFDR data should be sent to the PARMO as an electronic file. The specific format of the electronic file and the PARMO DFDR point of contact is contained in the following section.

To conduct the monitoring flight, the Monitoring Specialist or operator representative that has received GMS training, will perform the following tasks:

·  Submit preflight FIF to PARMO and GMS Support Contractor

·  Operate GMU

·  Submit post-flight FIF to PARMO and GMS Support Contractor

·  Submit GPS data files to GMS Support Contractor


The Monitoring process from the operator’s perspective is illustrated in Figure 1. The operator will be notified by a facsimile memo as the FIF, GPS data file, and pressure altitude data file move through the post-flight processing steps at the PARMO.

Digital Flight Data Recorder Data

Digital Flight Data Recorder (DFDR) data should contain altitude (ALT) expressed in feet with corresponding time (UTC) expressed in hours, minutes, and seconds HH/MM/SS to two decimal places and the aircraft transponder code (TXP). Altitude data submitted to the PARMO should have reports with 12-second or better intervals.

Providing aircraft position data for each level of flight further aids the PARMO in ASE calculation. Position data can be provided in latitude/longitude or range/azimuth (x/y) formats. A reference point is helpful when providing position data in the range/azimuth (x/y) format. Please provide the units of measurement for each piece of position data submitted to the PARMO.

DFDR Data Samples:

Range/Azimuth (X/Y) Data

TXP X Y ALT HH/MM/SS

5113 -284.969 197.938 36900 13/23/21.00

Latitude/Longitude Data

TXP LAT LON ALT HH/MM/SS

2241 54.833 4.494E 28000 17/57/42.00

2241 54.826 4.489E 28000 17/57/47.00

Sending DFDR data to the PARMO as an ASCII or text file via e-mail is recommended.

PARMO DFDR Point of Contact:

Phone: 1+609-485-5102

Fax: 1+609-485-5117

E-mail:

If e-mail is not available, the operator should send DFDR files on PC-formatted 3.5” diskettes to:

Anthony Strazzeri

FAA William J. Hughes Technical Center

ACB-310

Atlantic City Airport, NJ 08405

Monitoring Post-Flight Information

After completion of the monitoring flight, the GPS data will be processed by the GMS Contractor and forwarded to the PARMO. The operator will be advised by fax of the processing status of the data file. For the computation of the ASE, Meteorological data and Mode C data will be collected and merged with the GPS data at the PARMO. Final ASE results should be available from the PARMO within three weeks of the flight. The results will be sent to the State CAA and posted on the PARMO web site.

PARMO GMS Contacts:

PARMO Activities Coordinator

Phone: 1+609-485-5678

Fax: 1+609-485-5078

Email:

CSSI Inc., PARMO GMS Operations Coordinator:

Phone: 1+202-863-7426

Fax: 1+202-863-2398

Email:

1

GPS Procedures.doc Updated: 3 Feb 04

REDUCED VERTICAL SEPARATION MINIMUM (RVSM)

MONITORING APPLICATION

(Return completed form by fax to 1+609-485-5078 and 1+202-863-2398)

Operator Name:______

Address:______

______

Operator Primary Point of Contact

Name:______Title:______

Telephone Number:______Fax Number: ______Email Address:______

Secondary Point of Contact

Name:______Title:______

Telephone Number:______Fax Number: ______Email Address:______

Civil Aviation Authority Contact

Name:______Title:______

Telephone Number:______Fax Number: ______Email Address:______

______

AIRCRAFT INFORMATION

(Please be sure to include data for the ENTIRE fleet)

Aircraft Model / Registration Number / Serial Number

Flight Information Form (FIF)

Please Fax to the PARMO at 1+609 485 5078 and 1+202-863-2398,

24 hours prior to flight and within 6 hours of landing.

INFORMATION TO BE RECORDED PRIOR TO FLIGHT
Airline/Operator: / GMU Container Number:
Point of Contact for Operator:
Name: Phone: Fax:
Aircraft Type/Series: / Aircraft Registration Number:
Call Sign: / Airframe Serial Number:
Planned: Origin: Departure Date (UTC): Departure Time (UTC):
Planned: Destination: Arrival Date (UTC): Arrival Time (UTC):
Installer (Name/Org.): / Retriever (Name/Org.):
Mode S Equipped (Yes/No): Separation Between Mounted Antennas (ft.):
Installer/Operator Comments:
INFORMATION TO BE RECORDED BY FLIGHT CREW/GMU OPERATOR
Data Collection: / Start Date (UTC): / Start Time (UTC):
GMU File Name:
Departure Time (UTC): / Origin (ICAO ID):
Please record the requested information as soon as practical when:
1.  Aircraft is first established in level flight at or above FL 290, or
2.  The ATC assigned transponder code is changed at or above FL 290, or
3.  There is a flight level change and aircraft remains at or above FL 290, or
4.  An autopilot change is initiated at or above FL 290, or
5.  The ARTCC or FIR changes.
Time / Assigned / Mach/Air / Xpndr / Altimeter Reading / Autopilot (L, R, C) / FMS/PMS / ARTCC/FIR
(UTC) / FL / Speed / Code/Source / Pilot / Co-pilot / Pilot / Co-pilot / (Y/N) / (ICAO ID)
Data Collection: / End Date (UTC): / End Time (UTC):
Arrival Time (UTC): / Destination ICAO (ID):
Comments on flight conditions affecting height keeping performance, i.e. turb, and location

1