Essence™Series Windows

3-Part Specification

General Notes to Specifier:

This Specification Section has been prepared to assist design professionals in the preparation of Project or Office Master Specifications. It follows guidelines established by the Construction Specifications Institute, and therefore may be used with most Master Specification systems with minor editing.

Edit carefully to suit Project requirements. Modify as necessary and delete items that are not applicable. Verifythat referenced section numbers and titles are correct. Numbers and titles referenced are based on MasterFormat, 2004 edition.

This Section assumes the Project Manual will contain complete Division 1 documents, including Sections 01 25 13 Product Substitution Procedures, 01 33 00 – Submittal Procedures, 01 62 00 – Product Options, 01 66 00 – Product Storage and Handling Requirements, 01 7400 – Cleaning and Waste Management, 01 77 00 - Closeout Procedures, and 01 78 00 – Closeout Submittals. Close coordination with Division 1 Sections is required. If the Project Manual does not contain these Sections, additional information should be included under the appropriate articles.

This is an open proprietary specification allowing users the option of approving other manufacturers that comply with the criteria specified herein.

Notes to the specifier are contained in boxes and should be deleted from final copy.

Optional items requiring selection by the specifier are enclosed within brackets, e.g. [35] [40] [45]. Make appropriate selections and delete unused options.

Items requiring additional information are underlined blank spaces, e.g. ______.

Optional paragraphs requiring selection of one of the options are separated by “OR” within a box, e.g.

OR

Bold face type identifies optional paragraphs and features that may be included or deleted depending on Project requirements. Convert the bold face type to regular type when including these paragraphs or features.

Revise footer to suit Project/Office requirements.

Electronic versions of this specification utilize automatic paragraph numbering. When editing is complete, delete all text on this page, then remove the section break at the top of the next page to remove this page from the document.

SECTION 08 54 13

MASTER FORMAT™ 2004 EDITION

FIBERGLASS WINDOWS

PART 1 – GENERAL

Specifier note: information & data contained in this Guide is accurate as of July 2015. Due to ongoing product updates, data may change over time. Please contact your local Milgard Representative for complete product details. Please visit milgard.comfor the latest updates.

1.1 SUMMARY

  1. Section Includes:
  2. Awning windows
  3. Casement windows
  4. Double Hung windows
  5. Gliding windows
  6. Picture windows
  7. Radius windows
  8. Glazing
  9. Accessories
  1. Related Sections:

Specifier Note: Insert appropriate Section Numbers and Titles below for window flashing and installation sealant.

  1. 08 16 13- Fiberglass Doors.
  2. 08 16 73-Composite Sliding Doors.
  3. ______- ______.
  4. ______- ______.
  5. ______- ______.

Specifier Note: Include appropriate language below if products specified in this Section are to be bid as alternates,otherwise delete following paragraph.

  1. Alternates
  2. Reference Section 01 23 00 - Alternates
  3. SUBMITTALS
  1. Reference Section 01 33 00 - Submittal Procedure; submit following items:
  1. Product Data: Submit Milgard product data.
  2. Shop Drawings: Include window schedule, elevations, sections, details, & multiple-window assembly details. Include head, sill & jamb conditions; operable parts & direction/handing; and special mullion reinforcement details.
  3. Samples: Submit selection samples for verification, include the following:
  4. Exterior Color: Minimum 1x4 color chips on fiberglass substrate: (Specify)
  5. Wood Sample: Minimum 1x4 species sample: (Specify)
  6. Glass, showing specified tint color. (Specify)
  7. Hardware: Sample of style and typical finish: (Specify)
  1. Quality Assurance/Control Submittals:
  2. Qualifications: Proof of Manufacturer’s qualifications.
  3. U-Factor and Structural Rating charts required for NFRC and AAMA labeling requirements.
  4. Installation Instructions: AAMA 2400, (“Mounting Flange Installation”) or AAMA 2410 (“Flush Fin Installation”).
  5. Closeout Submittals: Reference Section 01 78 00 – Submit following items:
  6. Temporary window labels to identify windows that labels were applied to.
  7. Owner’s Manual/Maintenance Instructions.
  8. Special Warranties.
  9. QUALITY ASSURANCE
  1. Overall Standards: Comply with ANSI/AAMA/101/I.S.2, except where noted herein.
  2. Manufacturer Qualifications:
  1. Minimum 10 years experience in producing vinyl windows.
  2. Member AAMA & NFRC.
  1. Regulatory Requirements and Approvals:

Specifier Note: Insert local regulatory requirements

  1. Certifications for Insulated Glass Units:
  1. Insulated glass units are certified to ASTM E2188/E2190 per the Associated Laboratories Incorporated (ALI) guidelines.
  1. AAMA: Windows shall be Silver Label certified with label attached to frame per AAMA requirements.
  2. NFRC: Windows shall be NFRC certified with temporary U-factor label applied to glass and an NFRC tab added to permanent AAMA frame label.
  3. DELIVERY, STORAGE and HANDLING
  1. General: Reference Section 01 66 00 – Product Storage and Handling Requirements.
  2. Comply with Manufacturer’s/Dealer’s ordering instructions and lead time requirements to avoid construction delays.
  3. Delivery: Deliver materials in Manufacturer’s standard packaging for protection of product.
  4. Storage & Protection: Store products away from exposure to environmental conditions that may be harmful to materials.
  5. Store materials off ground in an upright position. Provide cover from weather and construction activity.
  6. Follow Manufacturer’s instructions on label applied to units.

1.5WARRANTY

Specifier Note: Select pertinent “Residential” warranty below for owner occupied single family residential and multi-family residential projects; select “Commercial” warranty for non-owner occupied condominiums, multi-family and commercial projects.

  1. Residential Special Warranty: (Owner Occupied Single Family Residential)
  2. Full Lifetime Warranty (including Glass Breakage) to original homeowner.
  3. Transferability:
  1. Permit unlimited transfer of ownership in first 10 years.
  2. Upon first transfer of ownership, warranty period shall become ten years from date of original purchase.
  3. Guarantee windows against defects in materials and workmanship including costs for replacement parts and labor.
  4. Submit, for Owner’s acceptance, Manufacturer’s Full Lifetime Warranty document.

OR

  1. Residential Special Warranty: (Owner Occupied Multi-Family Residential)
  2. 10 Year Multi-Family Limited Warranty.

OR

  1. Commercial Warranty:
  2. 10 Year Warranty.
  3. Guarantee windows against defects in materials and workmanship including costs for replacement parts and labor.

Part2 - PRODUCTS

2

2.1MANUFACTURER

  1. Products supplied by the following manufacturer:

Milgard Manufacturing, Inc.

1010 54th Avenue East

Tacoma, WA 98424

(800)-Milgard (645-4273)

milgard.com

Manufacturer’s Representative:

Specifier Note: Insert name, address and phone numbers of Manufacturer’s Representative below

Name: ______

Telephone: ______

Fax: ______

E-mail: ______

  1. Window Series: Milgard Essence™ Series
  2. Substitutions: Reference Section 01 25 13- Product Substitution Procedures
  3. MANUFACTURED UNITS
  1. Proprietary Products:
  2. Essence™ Series Windows
  3. Glazing
  4. Accessories
  5. Substitutions: No substitutions permitted.
  6. MATERIALS
  1. Frame and Sash
  2. Multi-chambered fiberglass pultrusion exterior
  3. 15 powder coat colors
  4. Wood Interior
  5. Unfinished Pine, Primed Pine, or Unfinished Douglas Fir
  6. Weatherstripping:
  7. Double Hung/Horizontal Slider: Foam filled seal
  8. Casement/Awning: Vinyl compression bulb seal

Specifier Note: Verify that window flashing material and installation sealant isspecified in appropriate sections.

2.4SYSTEM DESCRIPTION

  1. General Performance Requirements: Products and systems provided must be manufactured, fabricated, and installed to the following performance criteria:
  2. Comply with ANSI/AAMA/NWWDA 101/I.S.2, except as noted herein
  3. Performance Class: (Specify)
  4. Performance Grade: (Specify)
  5. U-Factor (NFRC 100): (Specify)
  6. SHGC – Solar Heat Gain Coefficient (NFRC 200): (Specify)
  7. OITC – Outdoor-Indoor Transmission Class (ASTM E90): (Specify)
  8. STC – Sound Transmission Class (ASTM E90): (Specify)
  1. Structural Requirements: Products and systems provided must be capable of withstanding wind loads based on testing units representative of those indicated for Project that pass AAMA/NWWDA 101/I.S.2/NAFS, Uniform Structural Load Test:
  1. Design Wind Loads: Determine design wind loads, according to ASCE, Section 6, applicable to Product from basic wind speeds (MPH) at 33 feet above grade, based upon mean roof heights indicated on Elevations/Drawings
  1. Basic Wind Speed: (Specify)
  2. Importance Factor: (Specify)
  3. Exposure Category: (Specify)
  4. Wind Load Requirement: (Specify)
  5. WINDOW TYPES

Specifier Note: Select from the following window types based on project requirements. Please note related Nail Fin and Insert window styles. Delete window types not used.

  1. Awning (New Construction)–9400 Series (crank-out, short bottom rail); 9420 Series (crank-out, tall bottom rail); [1-3/8” nail fin setback] [1” nail fin setback] [Z-bar flush fin]
  2. Frame: 3-1/4” minimum depth at sill, 2-7/8” at jamb and head. Multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: 2-1/2” minimumdepth. Multi-chambered fiberglass pultrusion with integral wood liner.
  4. Structural Class:AP-LC60
  5. Hardware:
  6. Scissor-arm, stainless steel rotary operator with nested, fold-down handle.
  7. Dual-lever, single-point locking mechanism (standard)
  8. Dual-lever, multi-point, around-the-corner locking mechanism (optional)
  9. Removable lock/operator handle and escutcheon covers.
  10. Two-bar, stainless steel, friction style hinge system.
  11. Weatherstripping: Vinyl compression bulb seal.
  12. Fixed Sash Picture Window (9340 Series, short bottom rail) (9350 Series, tall bottom rail)
  13. Structural Class:FW-LC60
  14. Sightlines: Equal to operating units.
  1. Awning (Insert Frame) – [94000 Series, crank-out, short bottom rail] [94200 Series, crank-out, tall bottom rail]
  2. Frame: 3-1/4” minimum depth at sill, 2-7/8” at jamb and head. Multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: 2-1/2” minimumdepth. Multi-chambered fiberglass pultrusion with integral wood liner.
  4. Structural Class: AP-LC40
  5. Hardware:
  6. Scissor-arm, stainless steel rotary operator with nested, fold-down handle.
  7. Dual-lever, single-point locking mechanism (standard).
  8. Dual-lever, multi-point, around-the-corner locking mechanism (optional).
  9. Removable lock/operator handles and escutcheon covers.
  10. Two-bar, stainless steel, friction style hinge system.
  11. Weatherstripping: Vinyl compression bulb seal.
  12. Fixed Sash Picture Window (93400 Series, short bottom rail) (93500 Series, tall bottom rail)
  13. Structural Class: FW-LC60
  14. Sightlines: Equal to operating units.
  1. Casement (New Construction) – 9500 Series (crank-out, short bottom rail); 9520 Series (crank-out, tall bottom rail); [1-3/8” nail fin setback] [1” nail fin setback] [Z-bar flush fin]
  2. Frame: 3-1/4” minimum depth at sill, 2-7/8” at jamb and head. Multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: 2-1/2” minimumdepth. Multi-chambered fiberglass pultrusion with integral wood liner.
  4. Structural Class: C-LC60
  5. Hardware:
  6. Dual-arm, stainless steel rotary operator with nested, fold-down handle (standard).
  7. Dyad-style, stainless steel rotary operator with nested, fold-down handle (optional).
  8. Multi-point, stainless steel lock bar system with single-point lock bar operator.
  9. Removable lock/operator handles and escutcheon covers.
  10. Two-bar, stainless steel, standard duty hinge (standard).
  11. Two-bar, stainless steel, standard duty egress hinge (optional).
  12. Two-bar, stainless steel, heavy duty hinge (optional).
  13. Weatherstripping: Vinyl compression bulb seal.
  14. Fixed Sash Picture Window (9340 Series, short bottom rail) (9350 Series, tall bottom rail)
  15. Structural Class: FW-LC60
  16. Sightlines: Equal to operating units.
  1. Casement (Insert Frame) – [95000 Series, crank-out, short bottom rail] [95200 Series, crank-out, tall bottom rail]
  2. Frame: 3-1/4” minimum depth at sill, 2-7/8” at jamb and head. Multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: 2-1/2” minimumdepth. Multi-chambered fiberglass pultrusion with integral wood liner.
  4. Structural Class: C-LC60
  5. Hardware:
  6. Dual-arm, stainless steel rotary operator with nested, fold-down handle (standard).
  7. Dyad-style, stainless steel rotary operator with nested, fold-down handle (optional).
  8. Multi-point, stainless steel lock bar system with single-point lock bar operator.
  9. Removable lock/operator handles and escutcheon covers.
  10. Two-bar, stainless steel, standard duty hinge (standard).
  11. Two-bar, stainless steel, standard duty egress hinge (optional).
  12. Two-bar, stainless steel, heavy duty hinge (optional).
  13. Weatherstripping: Vinyl compression bulb seal.
  14. Fixed Sash Picture Window (9340 Series, short bottom rail) (9350 Series, tall bottom rail)
  15. Structural Class: FW-LC60
  16. Sightlines: Equal to operating units.
  1. Double Hung Tilt (New Construction) – 9200 Series [1-3/8” nail fin setback] [1” nail fin setback]
  2. Frame: [2-13/16”] [5-1/16”] minimum depth, multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: [2”] [1-3/4”] minimum depth, multi-chambered fiberglass putrusion with integral wood liner. Tilt-in upper and lower sash.
  4. Structural Class:
  5. Up to 3050: DH-LC50
  6. Up to 4080: DH-LC30
  7. Hardware:
  8. Concealed block and tackle balance system (<=45 lbs. per sash)
  9. Concealed spiral balance system (>45 lbs. per sash)
  10. Lower sash lift handle (optional)
  11. Upper sash finger pull (optional)
  12. Flush mounted SmartTouch® lock (standard)
  13. Top mounted spoon-style cam lock (optional)
  14. Anti-slam/anti-mar, push-button style tilt latch system (standard)
  15. Weatherstripping: Foam filled seal.
  16. Fixed Sash Picture Window (9310 Series)
  17. Structural Class
  18. Up to 3050: FW-LC40
  19. Up to 8060: FW-LC30
  20. Sightlines: Equal to operating units
  1. Double Hung Tilt (Insert Frame) – [92008 Series, 8 degree sill] [92014 Series, 14 degree sill]
  2. Frame: [2-13/16”] [5-1/16”] minimum depth, multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: [2”] [1-3/4”] minimum depth, multi-chambered fiberglass putrusion with integral wood liner. Tilt-in upper and lower sash.
  4. Structural Class:
  5. Up to 3050: DH-LC45
  6. Up to 4080: DH-LC30
  7. Hardware:
  8. Concealed block and tackle balance system (<=45 lbs. per sash)
  9. Concealed spiral balance system (>45 lbs. per sash)
  10. Lower sash lift handle (optional)
  11. Upper sash finger pull (optional)
  12. Flush mounted SmartTouch® lock (standard)
  13. Top mounted spoon-style cam lock (optional)
  14. Anti-slam/anti-mar push-button style tilt latch system (standard)
  15. Weatherstripping: Foam filled seal.
  16. Fixed Sash Picture Window [93108 Series, 8 degree sill] [93114 Series, 14 degree sill]
  17. Structural Class
  18. Up to 3050: FW-LC40
  19. Up to 8060: FW-LC30
  20. Sightlines: Equal to operating units
  1. Glider/Horizontal Slider – 9100 Series [1-3/8” nail fin setback] [1” nail fin setback]
  2. Frame: [2-13/16”] [5-1/16”] minimum depth, multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: [2”] [1-3/4”] minimum depth, multi-chambered fiberglass putrusion with integral wood liner. Tilt-in sash.
  4. Structural Class:
  5. Up to 6050: HS-LC40
  6. Hardware:
  7. Adjustable, concave acetyl rollers with stainless steel axle and needle-bearing hub.
  8. Extruded aluminum, color-matched, monorail roller track.
  9. Flush mounted SmartTouch® lock (standard)
  10. Top mounted spoon-style cam lock (optional)
  11. Operable sash finger pull (optional)
  12. Anti-slam/anti-mar push-button style tilt latch sash removal/retention system (standard)
  13. Weatherstripping: Foam filled seal.
  14. Fixed Sash Picture Window (9310 Series)
  15. Structural Class
  16. Up to 8060: FW-LC30
  17. Sightlines: Equal to operating units
  1. Glider/Horizontal Slider (Insert Frame) – [91008 Series, 8 degree sill] [91014 Series, 14 degree sill]
  2. Frame: [2-13/16”] [5-1/16”] minimum depth, multi-chambered fiberglass pultrusion with integral wood liner.
  3. Sash: [2”] [1-3/4”] minimum depth, multi-chambered fiberglass putrusion with integral wood liner. Tilt-in sash.
  4. Structural Class:
  5. Up to 6050: HS-LC40
  6. Hardware:
  7. Adjustable, concave acetyl rollers with stainless steel axle and needle-bearing hub.
  8. Extruded aluminum, color-matched, monorail roller track.
  9. Flush mounted SmartTouch® lock (standard)
  10. Top mounted spoon-style cam lock (optional)
  11. Operable sash finger pull (optional)
  12. Anti-slam/anti-mar push-button style tilt latch sash removal/retention system (standard)
  13. Weatherstripping: Foam filled seal.
  14. Fixed Sash Picture Window 93100Series [8 degree sill] [14 degree sill]
  15. Structural Class
  16. Up to 8060: FW-LC30
  17. Sightlines: Equal to operating units
  1. Picture Window – Direct Set (non-bent) – [9300 Series, New Construction frame] [93000 Series, Insert frame]
  2. Frame: [3-11/16”] [5-1/16”] minimum depth, multi-chambered fiberglass pultrusion with integral wood liner.
  3. Structural Class:
  4. Up to 6060: FW-LC50
  1. Picture Window – Radius – 9700 Series [1-3/8” nail fin setback]
  2. Standard Frame (radius of ≥ 3 feet)
  3. [3-11/16”] [5-1/16”] minimum depth, ABS profile with integral wood liner.
  4. Narrow Frame (must be used with radius of < 3 feet; can be used with radius > 3 feet)
  5. Structural Class:
  6. Up to 6060: PG50
  7. Up to 8060: PG45

2.6GLAZING

  1. Insulated Glass Units: ASTM E 774, Class A
  2. Glazing Type: Dual or Triple Glaze (Specify)
  3. SunCoat® Low-E/Clear
  4. SunCoatMAX® Low-E/Clear
  5. SunCoat® Low-E/Clear/ SunCoat® Low-E
  6. SunCoatMAX® Low-E/Clear/ SunCoatMAX® Low-E
  7. [Tinted] [Obscure-several types] [Specialty] – Per Approval

Specifier Note:Most common types of insulated units are included above, but several other types, including tinted, reflective, tempered, obscure, wire, and laminated, are available for special applications. Select desired types from Milgard website and specify in lieu of, or in addition to,the above with all necessary criteria such as tint colors and obscure patterns. If more than one type of glazing is required for the Project, be certain that type for each window is clearly noted on drawings or in window schedule.

  1. Overall IG Unit Thickness:
  2. 1”.

Specifier Note: Warm edge spacers are not available on some units, including certain oversize units, radius units, and gable units.

  1. Spacer Type: EdgeGardMAX™
  2. Gas Filled: (Specify)
  3. Argon
  4. None
  5. Glass Thickness: (Specify)
  6. Per Manufacturer’s Specifications
  7. Special: Per Manufacturer’s Approval
  8. 3/32”, 1/8”, 3/16”, 1/4", 7/32” Laminate, Other
  1. GRIDS/GRILLES/MUNTINS:

Specifier Note: Select desired muntin type, if any, from the following list and delete those not used. Standard horizontal/vertical grid pattern will be provided unless other grid patterns are shown on the drawings. Certain grid patterns may not be available with one or the other bar types in the following paragraphs -consultMilgard for design other than standard patterns.

  1. Internal Grid (Grids Between Glass / GBG):
  2. Width: (Specify)
  3. 5/8” wide rectangular/flat aluminum bar internal muntin
  4. 1-1/16” wide sculptured aluminum bar internal muntin
  1. Simulated Divided Lite (SDL): (Specify)

Specifier Note: Exterior applied grids match exterior color of window and interior applied grids match specified wood for interior of window.